2010 HONDA INSIGHT lock

The childproof door locks are
designed to prevent children seated
in the rear f rom accidentally opening
the rear doors. Each rear door has a
lock lever near the edge. With the
lever in the LOCK position (lever is
down), the door cannot be opened
f rom the inside regardless of the
position of the lock tab. To open the
door, push the lock tab f orward and
use the outside door handle.
To lock any passenger’s door when
getting out of the vehicle, pull the
lock tab rearward and close the door.
To lock the driver’s door, remove the
key f rom the ignition switch, pull the
locktabrearwardorpushthefront
of the master switch, then close the
door.
When the vehicle speed reaches
about 10 mph (U.S.)/15 km/h
(Canada) or more, all the doors and
the hatch lock automatically.
When you shif t to P af ter driving, the
driver’s door unlocks.
If you f orget and leave the key in the
ignition switch, lockout prevention
will not allow you to lock the driver’s
door. With any door or the hatch
open and the key in the ignition
switch, locking with master door
lock switch is disabled. If the driver’s
door is closed, the lock tab on the
driver’s door is not disabled. Pulling
the driver’s lock tab rearward will
lock all doors or the hatch. If you try
to lock an open driver’s door by
pulling the lock tab rearward, the
driver’s door lock tab pops out and
unlocks the driver’s door.
Def ault setting
L ockout Prevent ion
Childproof Door L ocks
Door L ocks
Inst rument s and Cont rols
131
Unlock
Lock
LEVER
—
—y

y
)"y
y
2010 Insight

µµ
Press this button once to
lock all doors and the hatch. Some
exterior lights will f lash once. When
you push LOCK twice within 5
seconds, the horn will sounds to
verify that the doors are locked and
the security system has set. You
cannot lock the doors if any door or
the hatch is not f ully closed or if the
key is in the ignition switch. Press this button once
to unlock the driver’s door (or all the
doors and the hatch depending on
the door lock setting). Push it twice
to unlock the remaining doors and
the hatch. Some exterior lights will
flash twice when you push the
button the first time.
If you do not open any door or the
hatch within 30 seconds, the doors
automatically relock and the security
system sets. The ceiling light and the door
activated spotlights come on when
you press the UNLOCK button if the
lights are in the door activated
position. If you do not open any door
or the hatch within 30 seconds (or
whatever setting of the interior light
dimming time is set to), the light(s)
will f ade out. If you relock the doors
and the hatch with the remote
transmitter before 30 seconds have
elapsed, the light(s) will go of f
immediately.
To change the lock/unlock setting
and the relock timer setting, refer to
the customized settings on page . The keyless lock acknowledgment
beep and f lashing of the lights can
be deactivated (see page ).
106
112
LOCK UNL OCK
Remote Transmitter
132
LED
LOCK BUTTON
UNLOCK
BUTTON PANIC
BUTTON
—
—y

y
)"y
y
2010 Insight

µAvoid dropping or throwing the
transmitter.
Protect the transmitter from
extreme temperature.
Do not immerse the transmitter in
any liquid.
If you lose a transmitter, the
replacement needs to be
reprogrammed by your dealer. If it takes several pushes on the
button to lock or unlock the doors,
replace the battery as soon as
possible.
Battery type: CR1616
To replace the battery:
Press and hold this
button for about 1 second to attract
attention; the horn will sound, and
the exterior lights will f lash f or about
30 seconds. To cancel panic mode,
press any other button on the remote
transmitter, or turn the ignition
switch to the ON (II) position. Panic
mode does not work when the key is
in the ignition switch.
CONT INUED
Remote Transmitter CareReplacing the Transmitter
Battery
PA NIC
Remote Transmitter
Inst rument s and Cont rols
133
—
—y

y
)"y
y
2010 Insight

The hatch will lock or unlock when
you lock/unlock the driver’s door
with the key, the remote transmitter,
the master door lock switch, or the
locktabonthedriver’sdoor.
To unlock the hatch, turn the key
clockwise twice, push the rear of the
master door lock switch, or push
UNLOCK twice on the remote
transmitter.To open the hatch, pull and lif t up
the release. To close the hatch, use
thehandletolowerit,thenpress
down on the back edge.Keep the hatch closed at all times
while driving to avoid damaging the
hatch and to prevent exhaust gas
f rom getting into the interior. See
on page
.
56
Carbon Monoxide Hazard
Hatch
136
INNER HANDLE
RELEASE
—
—y


y
)"y

y
2010 Insight

If the power door lock system cannot
unlock the hatch, unlock it manually.
Placeaclothonthetopsideof the
cover, then use a small flat-tipped
screwdriver to remove the cover on
the back of the hatch.Push the release lever to the lower
right as shown, and push the hatch
to open it.
If you need to unlock the hatch
manually, it means there is a
problem with the hatch. Have the
vehicle checked by your dealer.
Unlocking the Hatch
Hatch
Inst rument s and Cont rols
137
Unlock
COVER
RELEASE LEVER
—
—y


y
)"y
y
2010 Insight

µ
The height of your driver’s seat is
adjustable. To raise the seat,
repeatedly pull up the lever on the
outside of the seat cushion. To lower
the seat, push the lever down
repeatedly.
To change the seat-back angle of the
f ront seat, pull up the lever on the
outside of the seat bottom.
Once a seat is adjusted correctly,
rock it back and f orth to make sure it
is locked in position.
To adjust the seat f orward or
backward, pull up on the bar under
the seat cushion’s f ront edge. Move
the seat to the desired position, and
releasethebar.Trytomovetheseat
to make sure it is locked in position. Make all adjustments bef ore you
start driving.
See pages f or important saf ety
inf ormation and warnings about how toproperly position seats and seat-backs. 14 15
Driver’s Seat Height A djustment
FrontSeatAdjustments
Seats
138
—
—y

y
)"y
y
2010 Insight

To remove a head restraint f or
cleaning or repair, pull it up as f ar as
it will go. Push the release button,
then pull the restraint out of the seat-
back.When reinstalling a head restraint,
put the legs back in place. Then
adjust it to the appropriate height
while pressing the release button.
Make sure the head restraint locks
in position when you reinstall it.
When a passenger is seated in the
rear seat, the head restraint should
be adjusted up or down, to match the
passenger’s height.
The Seat-back must be f olded
f orward (see page ) to get ceiling
clearance f or removal of the head
restraints.142
For Rear Seat Head Restraints
Removing t he Head Rest raint
Seats
140
LEGS SEAT-BACK
SEAT-BACK
LEGS RELEASE
BUTTON
Rear Outer Position
CUSHION Rear Center Position
CUSHION
RELEASE
BUTTON
Failure to reinstall the head
restraints can result in severe
injury during a crash.
Always replace the head
restraints before driving.
—
—y

y
)"y
y
2010 Insight

The rear seat-backs can be f olded
down f or more cargo room.
Each side f olds down separately, so
you can still carry one or two
passengers in the rear seat.Lower the rear head restraints to
their lowest positions. If you f old
down the right side seat-back, also
adjust the rear center head
restraint to its lowest position. Unlock the seat-back by pulling up
the release lever on the outer side
of each rear seat-back.
Fold the seat-back forward.
Remove any items from the seat
before folding down the seat-back,
and make sure there are no items on
the f loor bef ore f olding down the
seats. Reverse this procedure to return the
seat-back to the upright position. Pull
on the seat-back to make sure it is
latched. If the seat-back is not
latched f ully, the seat belt will not
work properly and you will see the
redindicatorbehindtherelease
lever as shown.
Do not put any heavy items on the
seat-back when it is folded down.
Make sure the seat-back and seat
cushion are locked securely and all
rear shoulder belts are positioned in
front of the rear seat-backs.
1. 2.
3.
Folding the Rear Seats Down
Seats
142
RED INDICATOR
LEVER
—
—y

y
)"y
y
2010 Insight