2010 HONDA INSIGHT S mode

This shows the average speed you
are traveling in miles per hour (mph)
f or U.S. models or kilometers per
hour (km/h) f or Canadian models.
This shows the accumulated
traveling time since you last reset it.
When you turn the ignition switch to
the ON (II) position, ELAPSED
TIME is reset.
This shows the estimated distance
you can travel on the fuel remaining
in the f uel tank. This distance is
estimated f rom the f uel economy
you received over the last several
miles(U.S.) or kilometers (Canada),
so it will vary with changes in speed,
traf f ic, etc.
If you want to reset the ELAPSED
TIME manually, go to the trip
computer’s ELAPSED TIME display,
andpressandholdtheSEL/RESET
button until the number resets.
You can customize the ELAPSED
TIME reset conditions on the multi-
inf ormation display (see page ).To reset the AVG. SPEED reading,
press and hold the SEL/RESET
button until the number resets.
100
EL A PSED T IME
RANGE A VG. SPEED
Multi-Inf ormation Display
Inst rument s and Cont rols
83
—
—y

y
)"yy
2010 Insight

On vehicle with paddle shif tersOn vehicle without paddle shif ters
The IMA battery is charged at a
higher rate when the transmission is
in L (Low) mode (see page ).
The battery level gauge does not
read the battery level directly. It
calculates the level by continuously
measuring the current f low, voltage,
and temperature. If the battery is mostly discharged,
the Auto Idle Stop f unction is
disabled (see page ). The IMA battery is charged at a
higher rate when the transmission is
in LOW (L) range (see page ). Since the level is not read directly,
small sensing errors can, over time,
cause the gauge to read higher than
the actual battery level. The system
will then perf orm a correction, and
the battery level gauge reading will
drop suddenly. When this happens,
IMA assist and Auto Idle Stop are
disabled until the IMA battery is
suf f iciently recharged by normal
driving.This correction of the battery level
gauge is normal and does not
indicate a problem. If the IMA
battery develops a problem or
becomes deteriorated, the IMA
system indicator will come on. If this
happens, have the vehicle checked
by your dealer as soon as possible.
320
314
322
Multi-Inf ormation Display
86
—
—y

y
)"y
y
2010 Insight

To use the system, your cell phone
and the HFL system must be linked.
Not all cell phones are compatible
with this system. Ref er to pagefor instructions on how to link
your cell phone to HFL and how to
receive or make phone calls, or visit
the handsf reelink.com website. In
Canada, visit , or call 1-
(888) 9-HONDA-9.
You can receive or make phone calls
f rom your cell phone through your
vehicle’s Bluetooth
HandsFreeLink(HFL) system
without touching your cell phone. 259
www.honda.ca
On models with navigation system
BluetoothHandsFreeL ink
Multi-Inf ormation Display
Inst rument s and Cont rols
87
—
—y

y
)"yy
2010 Insight

ÛÝ
You can customize some vehicle
control settings. To enter the
customizing mode, press and hold
either INFO button ( / ) for more
than 3 seconds. To change the
settings, the ignition switch must be
in the ON (II) position, and the
vehicle must be stopped with the
transmission in Park. If you turn the ignition switch to the
ACCESSORY (I) or the LOCK (0)
position, or move the shif t lever out
of Park, the display will change to
the normal screen.
If you try to enter the customizing
mode while the vehicle is moving,
you will see a ‘‘MUST STOP AND
SHIFTTOPARKTOCHANGE
SETTINGS’’ message and you
cannot change the settings.
If you want to change any vehicle
control settings, select CHG
SETTING, then press the SEL/
RESET button.
Ref er to the table on the f ollowing
pages about the settings you want to
customize.
CONT INUED
Customized Settings
Multi-Inf ormation Display
Inst rument s and Cont rols
91
—
—y

y
)"yy
2010 Insight

Î
Î
Î
Î
Î
Î
Î
Menu Item Description Setting Option
Group Setup Page
AUTO DOOR LOCK
AUTO DOOR UNLOCK
DOOR LOCK MODE
KEYLESS LOCK
ACKNOWLEDGMENT
SECURITY RELOCK
TIMERChanges when the doors automatically lock.
Changes when the doors automatically unlock.
Changes which doors unlock with the remote
transmitter in a first push.
The exterior lights flash each time you press the
LOCK or UNLOCK button. A beeper will also
sound when you press the LOCK button twice.
Changes how long it takes (in seconds) for the
doors to relock and the security system to set after
you unlock but do not open the door.
Set/Cancel all the customized settings as default. SHIFT FROM P
WITH VEH SPD
OFF
IGN OFF
OFF
DRIVER DOOR
ALL DOORS
ON
OFF
90 sec
60 sec
30 sec
SET
CANCEL
DOOR SETUP
(P.106)
DEFAULT ALL
(P.115)
107
108
110
112
113
115
Default setting
:
SHIFT TO P DRIVER DOOR /
AL L DOORS
Multi-Inf ormation Display
Inst rument s and Cont rols
93
—
—y

y
)"yy
2010 Insight

Û
Ý
ÛÝ
ÝÛ
LANGUAGE SELECTION
ADJUST OUTSIDE TEMP.
DISPLAY
Here are the f our custom settings
forthemetersetup:
TRIP A RESET with REFUEL
Each time you press the INFO ( / ) button, the screen changes as
shown in the illustration. Press the
INFO ( / ) button until you see
the setting you want to customize,
then press the SEL/RESET button
to enter your selection. While ‘‘METER SETUP’’ is shown,
press the SEL/RESET button to
enter the customize mode. METER COLOR CHANGE DISPLAY KM/MILES
ELAPSED TIME RESET
Meter Setup
Multi-Inf ormation Display
96
: Press the SEL/RESET button.
: Press the INFO button .
: Press the INFO button . See page
103
Seepage101
See page
97See page 98Seepage99 See page
100
—
—y

y
)"y

y
2010 Insight

ÛÝ
ÛÝ
Adjust Outside Temp. Display
If you sometimes f ind that the
temperature reading is a f ew
degrees above or below the actual
temperature, you can adjust it by
f ollowing these instructions: Adjust the outside temperature value
by pressing the INFO ( / ) button
repeatedly. Press the SEL/RESET
button to set the desired value.
When your selection is successf ully
completed, the display changes as
shown above, and then goes back to
the customize item screen.
If the ‘‘SETTING INCOMPLETE’’
message appears, go back to
‘‘ADJUST OUTSIDE TEMP.
DISPLAY’’ and repeat the procedure
again.
You can choose this item to
customize f rom ‘‘METER SETUP’’
by pressing the INFO ( / ) button
repeatedly.
Press the SEL/RESET button to
enter the setting.
Multi-Inf ormation Display
98
Canadian models
Canadian models
U.S. models
U.S. models
—
—y


y
)"y
y
2010 Insight

Û
Ý
ÛÝ
Ý
Û
There is one custom setting f or the
lighting setup:
INTERIOR LIGHT
DIMMING TIME
While ‘‘LIGHTING SETUP’’ is
shown, press the SEL/RESET
button to enter the customize mode.
Each time you press the INFO ( /) button, the screen changes as
shown in the illustration. Press the
INFO ( / ) button until you see
the setting you want to customize,
then press the SEL/RESET button
to enter your selection. Lighting Setup
Multi-Inf ormation Display
104
: Press the SEL/RESET button.
: Press the INFO button .
: Press the INFO button . See page
105
—
—y

y
)"y
y
2010 Insight