Page 89 of 450

On vehicle with paddle shif tersOn vehicle without paddle shif ters
The IMA battery is charged at a
higher rate when the transmission is
in L (Low) mode (see page ).
The battery level gauge does not
read the battery level directly. It
calculates the level by continuously
measuring the current f low, voltage,
and temperature. If the battery is mostly discharged,
the Auto Idle Stop f unction is
disabled (see page ). The IMA battery is charged at a
higher rate when the transmission is
in LOW (L) range (see page ). Since the level is not read directly,
small sensing errors can, over time,
cause the gauge to read higher than
the actual battery level. The system
will then perf orm a correction, and
the battery level gauge reading will
drop suddenly. When this happens,
IMA assist and Auto Idle Stop are
disabled until the IMA battery is
suf f iciently recharged by normal
driving.This correction of the battery level
gauge is normal and does not
indicate a problem. If the IMA
battery develops a problem or
becomes deteriorated, the IMA
system indicator will come on. If this
happens, have the vehicle checked
by your dealer as soon as possible.
320
314
322
Multi-Inf ormation Display
86
—
—y
y
)"y
y
2010 Insight
Page 94 of 450
ÛÝ
You can customize some vehicle
control settings. To enter the
customizing mode, press and hold
either INFO button ( / ) for more
than 3 seconds. To change the
settings, the ignition switch must be
in the ON (II) position, and the
vehicle must be stopped with the
transmission in Park. If you turn the ignition switch to the
ACCESSORY (I) or the LOCK (0)
position, or move the shif t lever out
of Park, the display will change to
the normal screen.
If you try to enter the customizing
mode while the vehicle is moving,
you will see a ‘‘MUST STOP AND
SHIFTTOPARKTOCHANGE
SETTINGS’’ message and you
cannot change the settings.
If you want to change any vehicle
control settings, select CHG
SETTING, then press the SEL/
RESET button.
Ref er to the table on the f ollowing
pages about the settings you want to
customize.
CONT INUED
Customized Settings
Multi-Inf ormation Display
Inst rument s and Cont rols
91
—
—y
y
)"yy
2010 Insight
Page 96 of 450
Î
Î
Î
Î
Î
Î
Î
Menu Item Description Setting Option
Group Setup Page
AUTO DOOR LOCK
AUTO DOOR UNLOCK
DOOR LOCK MODE
KEYLESS LOCK
ACKNOWLEDGMENT
SECURITY RELOCK
TIMERChanges when the doors automatically lock.
Changes when the doors automatically unlock.
Changes which doors unlock with the remote
transmitter in a first push.
The exterior lights flash each time you press the
LOCK or UNLOCK button. A beeper will also
sound when you press the LOCK button twice.
Changes how long it takes (in seconds) for the
doors to relock and the security system to set after
you unlock but do not open the door.
Set/Cancel all the customized settings as default. SHIFT FROM P
WITH VEH SPD
OFF
IGN OFF
OFF
DRIVER DOOR
ALL DOORS
ON
OFF
90 sec
60 sec
30 sec
SET
CANCEL
DOOR SETUP
(P.106)
DEFAULT ALL
(P.115)
107
108
110
112
113
115
Default setting
:
SHIFT TO P DRIVER DOOR /
AL L DOORS
Multi-Inf ormation Display
Inst rument s and Cont rols
93
—
—y
y
)"yy
2010 Insight
Page 115 of 450
ÛÝ
ÛÝ Press the SEL/RESET button to
enter the selecting mode.
Select ON or OFF by pressing the
INFO ( / ) button, then enter
your selection by pressing the SEL/
RESET button.
You can choose this item to
customize f rom ‘‘DOOR SETUP’’ by
pressing the INFO ( / ) button
repeatedly.
When you push the LOCK button on
the remote transmitter, some
exterior lights f lash, and a beeper
sounds when you push the LOCK
button again within 5 seconds to
verify that the doors and the trunk
arelockedandthesecuritysystem
has set (see page ). You can
customize the exterior lights not to
f lash and the beeper not to sound.
255
Keyless Lock Acknowledgment
Multi-Inf ormation Display
112
—
—y
y
)"y
y
2010 Insight
Page 118 of 450
ÛÝÛÝ
If you want to set the def ault settings,
press the INFO ( / ) button to
select DEFAULT ALL, then press
the SEL/RESET button.
If the setting is not successfully
completed, ‘‘FAILED’’ is shown f or
several seconds, and then the screen
goes back to the normal message
mode. Repeat the same procedure to
select DEFAULT ALL.
If you want to cancel DEFAULT
ALL, select CANCEL, then press the
SEL/RESET button. The screen
goes back to the previous display. To set the def ault settings, press the
INFO ( / ) button to select SET
then press the SEL/RESET button.
When DEFAULT ALL is set, you will
see the above display for several
seconds, then the screen returns to
the default all setting display.
DEFAUL T AL L
Multi-Inf ormation Display
Inst rument s and Cont rols
115
—
—y
y
)"y
y
2010 Insight
Page 119 of 450

Î
Î Î
Î
Î Î
Î
Î
Î Î Î
Î
Î
Î
Î To use the horn, press the center pad of the steering wheel.
Only on vehicles equipped with navigation system. Ref er to the navigation system manual. If equipped
1:
2:
3:
Controls Near the Steering Wheel
116
HEADLIGHTS/TURN SIGNALS
HORN
INSTRUMENT PANEL
BRIGHTNESS
VEHICLE STABILITY
ASSIST (VSA) OFF
SWITCH STEERING WHEEL
ADJUSTMENTCRUISE CONTROL BUTTONS
MULTI-INFORMATION BUTTONS
AUXILIARY INPUT JACK
MULTI-INFORMATION BUTTONS
ECON BUTTON
WINDSHIELD WIPERS/
WASHERS
REAR WINDOW DEFOGGER/
HEATED MIRRORCLOCK
ACCESSORY POWER SOCKET
REMOTE AUDIO
CONTROL BUTTONS
NAVIGATION SYSTEM
VOICE CONTROL
BUTTONS BLUETOOTH
HANDS-FREE LINKSYSTEM
VOICE CONTROL BUTTONS AUDIO SYSTEM
(P.333)
(P.251)
(P.259) (P.259) (P.252)(P.
254 )
(P.166)
(P.256)
(P.198)
NAVIGATION SYSTEM /
AUDIO SYSTEM
MIRROR CONTROLS
(P.118)
(P.144)
(P.124)
(P.125)(P.153)
(P.123/
145)
(P.121)
EX model with navigation system is shown. (P.117)
(P.
76)
(P.76)
1
2 2
2
2 2
2
2
3 2 3
2
—
—y
y
)"y
y
2010 Insight
Page 127 of 450
Press the ECON button to activate
the ECON mode. ECON ON will be
displayed on the multi-inf ormation
display and the ECON mode
indicator will illuminate in the
instrument panel. Press the ECON
button again to turn it off. ECON
OFF will appear on the multi-
inf ormation display.
The ECON button turns the ECON
mode on and of f . The ECON mode
helps you improve your f uel
economy by modif ying some vehicle
functions. When the ECON mode is
on: In addition, when the ECON mode is
on, you may get more Ecological
Drive Assist points (see page ).The climate control system will
have greater temperature
f luctuations Engine perf ormance will be
dif f erent Whenyouturnoff andthenrestart
the engine, the ECON mode setting
remains the same as previously set.
304
ECON Button
124
MULTI-INFORMATION DISPLAY
ECON BUTTON ECON MODE INDICATOR
—
—y
y
)"y
y
2010 Insight
Page 136 of 450
µAvoid dropping or throwing the
transmitter.
Protect the transmitter from
extreme temperature.
Do not immerse the transmitter in
any liquid.
If you lose a transmitter, the
replacement needs to be
reprogrammed by your dealer. If it takes several pushes on the
button to lock or unlock the doors,
replace the battery as soon as
possible.
Battery type: CR1616
To replace the battery:
Press and hold this
button for about 1 second to attract
attention; the horn will sound, and
the exterior lights will f lash f or about
30 seconds. To cancel panic mode,
press any other button on the remote
transmitter, or turn the ignition
switch to the ON (II) position. Panic
mode does not work when the key is
in the ignition switch.
CONT INUED
Remote Transmitter CareReplacing the Transmitter
Battery
PA NIC
Remote Transmitter
Inst rument s and Cont rols
133
—
—y
y
)"y
y
2010 Insight