2010 HONDA INSIGHT height

See page f or important saf etyinf ormation and a warning aboutimproperly positioning head restraints. 16
Your vehicle is equipped with head
restraints in all seating positions to
help protect you and your
passengers f rom whiplash and other
injuries.
They are most ef f ective when you
adjust them so the center of the back
of the occupant’s head rests against
the center of the restraint.The head restraints adjust f or height.
You need both hands to adjust a
restraint. Do not attempt to adjust it
while driving. To raise it, pull upward.
To lower the restraint, push the
release button sideways, and push
the restraint down.
CONT INUED
Head Restraints
A djust ing t he Head Rest raint
Seats
Inst rument s and Cont rols
139
LEGS
SEAT-BACK RELEASE
BUTTON
Front Position
CUSHION
—
—y

y
)"y
y
2010 Insight

To remove a head restraint f or
cleaning or repair, pull it up as f ar as
it will go. Push the release button,
then pull the restraint out of the seat-
back.When reinstalling a head restraint,
put the legs back in place. Then
adjust it to the appropriate height
while pressing the release button.
Make sure the head restraint locks
in position when you reinstall it.
When a passenger is seated in the
rear seat, the head restraint should
be adjusted up or down, to match the
passenger’s height.
The Seat-back must be f olded
f orward (see page ) to get ceiling
clearance f or removal of the head
restraints.142
For Rear Seat Head Restraints
Removing t he Head Rest raint
Seats
140
LEGS SEAT-BACK
SEAT-BACK
LEGS RELEASE
BUTTON
Rear Outer Position
CUSHION Rear Center Position
CUSHION
RELEASE
BUTTON
Failure to reinstall the head
restraints can result in severe
injury during a crash.
Always replace the head
restraints before driving.
—
—y

y
)"y
y
2010 Insight

Beforeusinganautomaticcarwash,
remove the radio antenna so it does
not get damaged. Remove the
antenna by unscrewing it. When you
reinstall the antenna, tighten it
securely.
Bef ore entering or parking in areas
with low ceiling height, remove the
antenna.The driver’s f loor mat that came
with your vehicle hooks over the
f loor mat anchors. To lock each
anchor, turn the knob clockwise.
This keeps the f loor mat f rom sliding
f orward and possibly interf ering with
the pedals.
If your seat belts get dirty, use a sof t
brush with a mixture of mild soap
and warm water to clean them. Do
not use bleach, dye, or cleaning
solvents. Let the belts air dry bef ore
you use the vehicle.
Dirt build-up in the loops of the seat
belt anchors can cause the belts to
retract slowly. Wipe the insides of
the loops with a clean cloth
dampened in mild soap and warm
water or isopropyl alcohol.
When cleaning or replacing, turn the
knob counterclockwise to unhook
the floor mat.
CONT INUED
On all Canadian models
Roof A ntenna
Floor Mats
Cleaning the Seat Belts
Roof A ntenna, Cleaning the Seat Belts, Floor Mats
Maint enance
369
LOOP
To unlock
Driver’s floor mat is shown.
—
—y

y
)"yy
2010 Insight

Î
Î
Î
Î
Specif ications
418
Dimensions
Weights
Seating CapacitiesCapacities
Engine 172.3 in (4,377 mm)
66.7 in (1,695 mm)
56.2 in (1,427 mm)
100.4 in (2,550 mm)
58.7 in (1,492 mm)
58.1 in (1,475 mm)
Length
Width
Height
Wheelbase
Track
Gross vehicle weight rating See the certification label attached
to the driver’s doorjamb. 3.4 US qt (3.2
)
3.2 US qt (3.0)
4.0 US qt (3.8)
Total
Front
Rear 5
2
3
Excluding the oil remaining in the engine Including the coolant in the reserve tank and that remaining in the
engine
Reserve tank capacity: 0.116 US gal (0.44
)
2.6 US qt (2.5
)
5.12 US qt (4.85)
Fuel tank
Engine
coolant
Engine oil
Automatic
transmission
fluid (CVTF)
Windshield
washer
reservoir
Type
BorexStroke
Displacement
Compression ratio
Spark plugs DILFR6F11G10.8 : 1
82 cu-in (1,339 cm
)
2.87 x 3.15 in (73.0 x 80.0 mm) 3.0 US qt (2.8
)
5.5 US qt (5.2)
10.6 US gal (40
)
1.202 US gal (4.55)
1.332 US gal (5.04)
Water cooled 4-stroke SOHC i-VTEC gasoline engine with Hybrid Electric Motor
Front
Rear
Approx.
1:
2:
(NGK) Change
Total
Change
Including filter
Without filter
Total
Change
Total
U.S. Vehicles
Canada Vehicles
1
2
—
—y

y
)"yy
2010 Insight

µ
µ
µ
µ
µ
µ
µ
µ
µ
µ µ
µ Tire type code.
Date of manufacture.
Whenever tires are replaced, they
should be replaced with tires of the
same size. The f ollowing is an
exampleof tiresizewithan
explanation of what each component
means. Load index (a numerical code
associated with the maximum
load the tire can carry).
Speed symbol (an
alphabetical code indicating
the maximum speed rating).
The tire identif ication number (TIN)
is a group of numbers and letters
that look like the f ollowing example.
TIN is located on the sidewall of the
tire.
This indicates that the tire
meets all requirements of
the U.S. Department of
Transportation. Max Press The maximum air
pressurethetirecan
hold.
Max Load The maximum load the tire can carry at
maximum air pressure.
Year
Week
Tire width in millimeters.
Aspect ratio (the tire’s section
height as a percentage of its
width).
Tire construction code (R
indicates radial).
Rim diameter in inches. Manuf acturer’s
identification mark.
R
DOT2202
S
65
15 175 84
EUYU2KNR
Tire Labeling
Tire Size
T ire Ident if icat ion Number (T IN)Maximum T ire L oad
Maximum T ire Pressure
422
DOT EUYU 2KNR 2202
175/65R15 84S
—
—y

y
)"yy
2010 Insight