2010 FORD KUGA ignition

Horn.
E
Wiper lever. See Wipers and washers (page 41).
F
Card holder.
G
Air vents. See Air vents(page 80).
H
Hazard warning flasher switch. See Hazard warning flashers(page 48).
I
Airbag deactivation indicator. See Disabling the passenger airbag (page
25). Parking aid switch. See Using the parking aid(page 115).
J
Start button. See Keyless starting (page 101).
J
Heated windscreen switch. See Heated windows and mirrors (page
86).
K
Heated rear window switch. See Heated windows and mirrors (page
86).
L
Climate controls. See Climate control(page 80).
M
Audio or navigation unit. See separate handbook.
N
Heated front seat switch. See Heated seats(page 94).
O
Ignition switch.
P
Steering wheel adjustment. See Adjusting the steering wheel (page 39).
Q
Cruise control switches. See Using cruise control(page 120).
R
Audio controls. See Audio control(page 39).
S
Instrument lighting dimmer. See Instrument lighting dimmer(page 96).
T
10Quick start

Disabling the passenger airbag
Disabled
A
Enabled
B
Turn the switch to position A.
When you switch the ignition on, check
that the passenger airbag deactivation
warning lamp illuminates.
Enabling the passenger airbag WARNING
Make sure that the passenger
airbag is enabled when you are
not
using a child restraint on the front
passenger seat. Turn the switch to position
B.
26
Occupant protectionABE71312

Unlocking the vehicle
Note:If the vehicle remains locked for
longer than three days, the key free system will enter an energy-saving mode.This is to reduce the discharge of thevehicle battery. When the vehicle isunlocked while in this mode, the reactiontime of the system may be a little longerthan normal. Unlocking the vehicle oncewill deactivate the energy-saving mode. Pull one of the door handles or the
luggage compartment lid handle.
Note:
A valid passive key must be
located within the detection range of that door.
One long flash of the direction indicators
confirms that all the doors, the luggage
compartment lid and the fuel filler flap
have been unlocked and that the alarm
has been disarmed.
Unlocking only the driver's door
If the unlocking function is reprogrammed
so that only the driver’s door is unlocked
( See Programming the remote
control (page 27). ), note the following: If the driver’s door is the first door which
is opened, the other doors and the
luggage compartment lid will remain
locked. All the other doors can be
unlocked from inside the vehicle by using
the unlock button next to the driver’s door
handle. Doors can be unlocked individually
by pulling the interior door handles on
those doors.
If the front passenger door or one of the
rear doors is the first door which is
opened,
allthe doors and the luggage
compartment lid will be unlocked.
Disabled keys
Any keys left inside the vehicle interior
when it is locked will be disabled.
A disabled key cannot be used to turn the
ignition on or start the engine.
In order to use these passive keys again,
they have to be enabled.
To enable all your passive keys, unlock
the vehicle using a passive key or the
remote control unlocking function.
All passive keys will then be enabled if the
ignition is turned on or the vehicle is
started using a valid key.
33
LocksE78278

Locking and unlocking the
doors with the key blade
1. Slide the release slider in the direction
of the arrow and pull out the key blade
with your thumb.
2. Remove the key blade and insert it into the lock.
GLOBAL OPENING AND
CLOSING
You can also operate the electric
windows with the ignition off via the global
opening and global closing function.
Note:Global closing will only operate if
you have set the memory correctly for
each window. See Electric windows
(page 60).
Global opening To open all the windows, press and hold
the
unlock button for at least three
seconds. Press either the lockor the
unlock button again to stop the opening
function.
Global closing WARNING
Take care when using global
closing. In an emergency, press the
button on the driver’s door handle
to stop. Note:
Global closing can be activated
using the button on the driver’s door handle. Global opening and closing canalso be activated using the buttons on thepassive key.
34
Locks12E78284 E71955

PRINCIPLE OF OPERATION
The engine immobiliser is a theft
protection system that prevents someone
from starting the engine with an
incorrectly coded key.
CODED KEYS
Note:Do not shield your keys with metal
objects. This may prevent the receiver from recognising your key as a valid one.
Note:Have all of your remaining keys
erased and recoded if you lose a key. Ask your dealer for further information. Havereplacement keys recoded together withyour existing keys.
If you lose a key, you can obtain a
replacement from your Ford Dealer. If
possible, provide them with the key
number from the tag provided with the
original keys. You can also obtain
additional keys from your Ford Dealer.
ARMING THE ENGINE
IMMOBILISER
The engine immobiliser is armed
automatically a short time after you have
switched the ignition off.
DISARMING THE ENGINE
IMMOBILISER
The engine immobiliser is disarmed
automatically when you switch the ignition
on with a correctly coded key. The indicator in the instrument cluster will
come on for approximately three seconds
and then go out. If the indicator stays on
for one minute or flashes for
approximately one minute and then
repeatedly at irregular intervals, your key
has not been recognised. Remove the
key and try again.
If you are unable to start the engine with
a correctly coded key, this indicates a
malfunction. Have the immobiliser
checked immediately.
36
Engine immobiliser

CHANGING THE WIPER
BLADES
Windscreen wiper blades
CAUTIONS
Set the windscreen wipers in the
service position to change the wiper
blades.
You can use the service position in
winter to provide easier access to
the wiper blades for freeing them
from snow and ice. The windscreen
wipers will return to their normal position
as soon as you switch on the ignition so
make sure that the outside of the
windscreen is free from snow and ice
before you switch on the ignition. Service position 1. Turn on the ignition.
2.
Move the wiper lever to position Aand
turn the ignition off as soon as the
wiper blades have reached the service
position.
Changing the windscreen wiper
blades
Set the windscreen wipers in the service
position and lift the wiper arms. 1. Press the locking button.
2. Remove the wiper blade.
Note:Make sure that the wiper blade
locks into place.
3. Install in the reverse order.
44
Wipers and washersE85833 E99280A E7289912

LIGHTING CONTROL
Lighting control positions
OffA
Side and tail lamps
B
Headlamps
C
Front fog lamps
D
Rear fog lamps
E
Parking lamps
F
Parking lamps CAUTION
Prolonged use of the parking lamps
will discharge the battery.
Switch off the ignition.
Push the lighting control inwards and turn
it to position
F. Main and dipped beam
Pull the lever fully towards the steering
wheel to switch between main and
dipped beam.
Headlamp flasher
Pull the lever slightly towards the steering
wheel.
Home safe lighting
Switch the ignition off and pull the
direction indicator lever towards the
steering wheel to switch the headlamps
on. You will hear a short tone. The
headlamps will go off automatically after
3 minutes with any door open, or 30
seconds after the last door has been
closed.
With all doors closed, but within the 30
second delay, opening any door will result
in the 3 minute timer starting again.
The home safe lights can be cancelled by
either pulling the direction indicator lever
towards the steering wheel again or by
turning the ignition switch ON.
46
LightingE71094DBCAFE E71095

DIRECTION INDICATORS
Note:Tap the lever up or down to make
the direction indicators flash only three times.
INTERIOR LAMPS
Courtesy lamp OffA
Door contact
B
OnC If you set the switch to position
B, the
courtesy lamp will come on when you
unlock or open a door or the luggage
compartment lid. If you leave a door open
with the ignition switch off, the courtesy
lamp will go off automatically after some
time to prevent the vehicle battery from
discharging. To switch it back on, switch
on the ignition for a short time.
The courtesy lamp will also come on when
you switch off the ignition. It will go off
automatically after a short time or when
you start or restart the engine.
If you set the switch to position Cwith the
ignition switch off, the courtesy lamp will
come on. It will go off automatically after
a short time to prevent the vehicle battery
from discharging. To switch it back on,
switch on the ignition for a short time.
Reading lamps If you switch off the ignition, the reading
lamps will go off automatically after some
time to prevent the vehicle battery from
discharging. To switch them back on,
switch on the ignition for a short time.
50
LightingE71098 CBAE71945 E71946