2010 FORD KUGA Page 71

ADJUSTING THE STEERING
WHEEL
WARNING
Never adjust the steering wheel
when the vehicle is moving.
Note:Make sure that you are sitting in
the correct position. See Sitting in the
correct position (page 90). WARNING
Make sure that you fully engage the
locking lever when returning it to its
original position.
AUDIO CONTROL
Select radio, CD or cassette mode on the
audio unit.
The following functions can be operated
with the remote control:
Volume
Volume up: Press the top button on the
back of the remote control.
Volume down: Press the bottom button
on the back of the remote control.
39
Steering wheel122E95178 3E95179 E78046

Seek
Move the lever up or down:
•
In
radio mode, this will locate the
next radio station up or down the
frequency band.
• In
CD mode, it will select the next or
previous track.
Mode Briefly press the button on the side: •
In
radio mode, this will locate the
next pre-set radio station.
• In
CD mode, this will select the next
CD if a CD changer is fitted.
• In
all modes to abort a traffic
message during broadcasting.
Press and hold the button on the side:
• In
radio mode to change the
waveband.
VOICE CONTROL To select or deselect voice control, press
the button on the top.
For further information See
Voice
control (page 182).
40
Steering wheelE78047 E78048 E78049

Rear window washer
WARNING
Do not operate the washer for more
than 10 seconds at a time, and
never when the reservoir is empty.
While the lever is pulled towards the
steering wheel the washer will work in
conjunction with the wipers.
Once the wash and wipe cycle is
completed, the wipers will pause and then
perform one more wipe to clear the
windscreen.
After releasing the lever, the wipers
operate for a short time.
ADJUSTING THE
WINDSCREEN WASHER
JETS
1.
Open the bonnet. See Opening and
closing the bonnet (page 142). 2. Using a suitable implement adjust the
jets.
3. Close the bonnet and check the operation of the jets. See Opening
and closing the bonnet (page 142).
HEADLAMP WASHERS
The headlamp washers will operate with
the windscreen washers when the
headlamps are on.
Note:To stop the washer fluid reservoir
emptying quickly, the headlamp washers will not operate every time that you usethe windscreen washers.
CHECKING THE WIPER
BLADES Run the tip of your fingers over the edge
of the blade to check for roughness.
Clean the wiper blade lips with water
applied with a soft sponge.
43
Wipers and washersE71018 E99777 E66644

You can adjust the level of the headlamp
beams according to the vehicle load.
Recommended headlamp levelling control positions
Control position
Load in luggage
compartment 1
Load
Rear seats
Front seats
0
-
-
1-2
1
-
3
1-2
1.5
Max
3
1-2
3
Max
-
1
1 See Vehicle identification plate (page 170).
HAZARD WARNING
FLASHERS
Note:Depending on applicable laws and
regulations in the country for which your vehicle was originally built, the hazardwarning flashers may flash if you brakeheavily. For item location: See
Quick start(page
8).
48
LightingE71943

ADAPTIVE FRONT LIGHTING SYSTEM (AFS)
without AFS
A
with AFS
B
The AFS adjusts the headlamp dipped
beam depending on vehicle direction and
speed. It improves visibility when you are
driving at night and helps to reduce
headlamp glare for oncoming drivers.
The headlamps will also move when the
vehicle is stationary and the steering
wheel is turned. To prevent headlamp
glare for the oncoming traffic, they will only
move towards the passenger side of the
vehicle.
The system will not operate when you
have switched on the daytime running
lamps or when you have selected reverse
gear. To activate the AFS when the daytime
running lamps are activated, turn the
lighting control to position
C. See
Lighting control (page 46).
A message will appear in the information
display and the headlamp indicator flashes
if the system malfunctions. See
Information messages (page 73).
The headlamps will move to a fixed central
or dipped position. Have the system
checked as soon as possible.
49
LightingE72897ABAB

Vanity mirror lamps
OffA
OnB
If you switch off the ignition, the vanity
mirror lamps will go off automatically after
a short time to prevent the vehicle battery
from discharging. To switch them back
on, switch on the ignition for a short time.
REMOVING A HEADLAMP WARNING
Have Xenon bulbs changed by a
trained technician. There is a risk of
electric shock.
1.
Open the bonnet. See Opening and
closing the bonnet (page 142). 2. Remove the screw.
3. Using a suitable implement, remove
the trim panel. 4. Release the retaining clips.
51
LightingABE72900 23E99388 4E99389

5. Disconnect the electrical connector.
6. Disconnect the headlamp washer
hose.
7. Remove the headlamp.
Note:When fitting the headlamp, make
sure that you fully engage the headlamp in the retaining clips.
CHANGING A BULB WARNINGS
Switch the lights and the ignition off.
Let the bulb cool down before
removing it.
Have Xenon bulbs changed by a
trained technician. There is a risk of
electric shock.
CAUTIONS
Do not touch the glass of the bulb.
Only fit bulbs of the correct
specification. See
Bulb
specification chart (page 58). Headlamp
Direction indicator
1. Remove the headlamp. See
Removing a headlamp (page 51). 2. Turn the bulb holder anti-clockwise
and remove it.
3. Gently press the bulb into the bulb holder, turn it anti-clockwise and
remove it.
Headlamp main and dipped beam
Note:
Remove the covers to gain access
to the bulbs.
1. Remove the headlamp. See
Removing a headlamp (page 51). 52
Lighting567E99390 E9948232 E7226032

2. Turn the bulb holder anti-clockwise
and remove it.
3. Remove the bulb.
Side lamp
1. Remove the headlamp. See Removing a headlamp (page 51).2. Remove the cover.
3. Pull the bulb holder and remove it.
Remove the bulb.
Side repeaters 1. Remove the cover.
2. Release the retaining clip.
3. Remove the bulb and bulb holder.
Remove the bulb.
Approach lamp Note:Position the mirror glass as far
inwards as possible.
1. Insert a screwdriver into the gap between the mirror housing and the
mirror glass and release the metal
retaining clip.
53
LightingE9943723 1E99397 23E99398 E722641