2010 FORD FOCUS spare tire

Tire change procedure
WARNING:When one of the front wheels is off the ground, the
transmission alone will not prevent the vehicle from moving or
slipping off the jack, even if the vehicle is in P (Park) (automatic
transmission) or R (Reverse) (manual transmission).
WARNING:To help prevent the vehicle from moving when you
change a tire, be sure the parking brake is set, then block (in
both directions) the wheel that is diagonally opposite (other side and
end of the vehicle) to the tire being changed.
WARNING:If the vehicle slips off the jack, you or someone else
could be seriously injured.
WARNING:Do not attempt to change a tire on the side of the
vehicle close to moving traffic. Pull far enough off the road to
avoid the danger of being hit when operating the jack or changing the
wheel.
Note:Passengers should not remain in the vehicle when the vehicle is
being jacked.
1. Remove the spare tire and jack by
turning their tie-down bolts
counterclockwise. The lug wrench is
located in a bag next to, or on top
of, the spare tire.
2. Block the diagonally opposite
wheel.
Roadside Emergencies
202
2010 Focus(foc)
Owners Guide, 1st Printing
USA(fus)

WARNING:To lessen the risk of personal injury, do not put any
part of your body under the vehicle while changing a tire. Do not
start the engine when your vehicle is on the jack. The jack is only
meant for changing the tire.
6. Remove the lug nuts with the lug wrench.
7. Replace the flat tire with the spare tire, making sure the valve stem is
facing outward. Reinstall the lug nuts until the wheel is snug against the
hub. Do not fully tighten the lug nuts until the wheel has been lowered.
8. Lower the wheel by turning the jack handle counterclockwise.
9. Remove the jack and fully tighten
the lug nuts in the order shown.
Refer toWheel lug nut torque
specificationslater in this chapter
for the proper lug nut torque
specification.
10. Put the flat tire, jack and lug
wrench away. Make sure the jack is
fastened so it does not rattle when
you drive. Unblock the wheels.
WHEEL LUG NUT TORQUE SPECIFICATIONS
Retighten the lug nuts to the specified torque at 500 miles (800 km)
after any wheel disturbance (tire rotation, changing a flat tire, wheel
removal, etc.).
Bolt size Wheel lug nut torque*
lb. ft. N•m
M12 x 1.5 100 135
* Torque specifications are for nut and bolt threads free of dirt and
rust. Use only Ford recommended replacement fasteners.
1
4 3
2
Roadside Emergencies
204
2010 Focus(foc)
Owners Guide, 1st Printing
USA(fus)

snow tires and chains ............163
spare tire .................................199
terminology .............................145
tire grades ...............................145
treadwear ........................144, 149
Towing .......................................169
recreational towing .................169
trailer towing ..........................169
wrecker ....................................211
Transmission
automatic operation ...............184
brake-shift interlock (BSI) ....183
fluid, checking and adding
(automatic) .............................253
fluid, checking and adding
(manual) .................................256
fluid, refill capacities ..............258
lubricant specifications ..........258
manual operation ....................187
Trunk ...........................................72
remote release ....................67, 75
Turn signal ..................................48
U
USB port ......................................35V
Vehicle Identification Number
(VIN)
..........................................263
Vehicle loading
..........................163
Ventilating your vehicle
...........174
W
Warning lights (see Lights)
.......12
Washer fluid
..............................231
Water, Driving through
.............189
Windows
power
.........................................59
Windshield washer fluid and
wipers
..........................................55
checking and adding fluid
.....231
replacing wiper blades
...........231
Wrecker towing
.........................211
Index
275
2010 Focus(foc)
Owners Guide, 1st Printing
USA(fus)