2010 FORD F250 SUPER DUTY coolant reservoir

Fill your engine coolant reservoir as outlined in Adding engine coolant
in this section.
Severe climates
If you drive in extremely cold climates (less than –34°F [–36°C]):
• It may be necessary to increase the coolant concentration
above 50%.
• NEVER increase the coolant concentration above 60%.
Increased engine coolant concentrations above 60% will
decrease the overheat protection characteristics of the engine
coolant and may cause engine damage.
• Refer to the chart on the coolant container to ensure the
coolant concentration in your vehicle will provide adequate
freeze protection at the temperatures in which you drive in the
winter months.
If you drive in extremely hot climates:
• It is still necessary to maintain the coolant concentration
above 40%.
• NEVER decrease the coolant concentration below 40%.
Decreased engine coolant concentrations below 40% will
decrease the corrosion/freeze protection characteristics of the
engine coolant and may cause engine damage.
• Refer to the chart on the coolant container to ensure the
coolant concentration in your vehicle will provide adequate
protection at the temperatures in which you drive.
Vehicles driven year-round in non-extreme climates should use a 50/50
mixture of engine coolant and distilled water for optimum cooling system
and engine protection.
What you should know about fail-safe cooling (if equipped)
If the engine coolant supply is depleted, this feature allows the vehicle to
be driven temporarily before incremental component damage is incurred.
The “fail-safe” distance depends on ambient temperatures, vehicle load
and terrain. Maintenance and Specifications
369
2010 F-250/350/450/550 (f23)
Owners Guide, 2nd Printing
USA (fus)

How fail-safe cooling works
If the engine begins to overheat:
• The engine coolant temperature gauge will move to the red (hot)
area.
• The message center will indicate the engine is overheating.
• The service engine soon indicator will illuminate.
If the engine reaches a preset over-temperature condition, the engine
will automatically switch to alternating cylinder operation. Each disabled
cylinder acts as an air pump and cools the engine.
When this occurs the vehicle will still operate. However:
• The engine power will be limited.
• The air conditioning system will be disabled.
Continued operation will increase the engine temperature and the engine
will completely shut down, causing steering and braking effort to
increase.
Once the engine temperature cools, the engine can be re-started. Take
your vehicle to a service facility as soon as possible to minimize engine
damage.
When fail-safe mode is activated
You have limited engine power when in the fail-safe mode, so drive the
vehicle with caution. The vehicle will not be able to maintain high-speed
operation and the engine will run rough. Remember that the engine is
capable of completely shutting down automatically to prevent engine
damage; therefore:
1. Pull off the road as soon as safely possible and turn off the engine.
2. Arrange for the vehicle to be taken to a service facility.
3. If this is not possible, wait a short period for the engine to cool.
4. Check the coolant level and replenish if low.
WARNING: Never remove the coolant reservoir cap while the
engine is running or hot.
5. Re-start the engine and take your vehicle to a service facility.
Driving the vehicle without repairing the engine problem
increases the chance of engine damage. Take your vehicle to a
service facility as soon as possible.Maintenance and Specifications
370
2010 F-250/350/450/550 (f23)
Owners Guide, 2nd Printing
USA (fus)

MAINTENANCE PRODUCT SPECIFICATIONS AND CAPACITIES
Item Capacity Ford part name Ford part number /
Ford specification
Front axle 5.8 pints (2.8L) Motorcraft SAE 80W-90
Premium Rear Axle
Lubricant XY-80W-90–QL /
WSP-M2C197–A
Spindle bearing — High Temperature 4X4
Front Axle and Wheel
Bearing Grease XG-11 /
WSS-M1C267-A1
Rear axle - F-250/350
(10.50 inch axle)
16.9 pints (3.3L) Motorcraft SAE 75W-140
Synthetic Rear Axle
Lubricant XY-75W140–QL /
WSL-M2C192-A
Rear axle - F-350
(DANA M80) 8.5 pints (4.0L) Motorcraft SAE 75W-90
Synthetic Rear Axle
Lubricant XY-75W90–QLS /
WSS–M2C918–A
Rear axle - F-450/550
(Dana S110/S130) 14.0 pints (6.6L) Motorcraft SAE 75W-140
Synthetic Rear Axle
Lubricant XY-75W140–QL /
WSL-M2C192-A
Brake fluid (and clutch
fluid, if equipped) Fill to line or step
(for clutch) on
reservoir Motorcraft High
Performance DOT 3
Motor Vehicle Brake
Fluid PM-1–C / WSS-M6C62-A
or WSS-M6C65-A1
Engine coolant
(5.4L V8 engine)
225.7 quarts
(24.3L) Motorcraft Premium
Gold Engine Coolant
(yellow-colored) VC-7-B /
WSS-M97B51-A1Maintenance and Specifications
391
2010 F-250/350/450/550 (f23)
Owners Guide, 2nd Printing
USA (fus)