2010 DODGE JOURNEY wheel

TOWING A DISABLED VEHICLE
Without The Ignition Key
Front Wheel Drive (FWD)
Special care must be taken when the vehicle is towed
with the ignition in the LOCK position. Flatbed towing is
the preferred towing method. However, if a flatbed
towing vehicle is not available, a wheel lift towing
vehicle may be used. Furthermore, rear towing is not
recommended with the front wheels on the ground, as
transaxle damage can result. If rear towing is the only
alternative, a front end dolly must be used. Proper
towing equipment is necessary to prevent damage to the
vehicle.
All Wheel Drive (AWD)
The manufacturer requires towing your vehicle with all
four wheelsOFFthe ground using a flatbed.
CAUTION!
Towing this vehicle using any other method could
result in extensive damage to the transfer case and/or
transmission. Such damage is not covered by the
New Vehicle Limited Warranty.
Towing This Vehicle Behind Another Vehicle (Flat
Towing With The Key In The Ignition And All Four
Wheels On The Ground)
CAUTION!
•If the vehicle being towed requires steering, the
ignition switch must be in the ON position, not in
the LOCK or ACC position.
(Continued)
398 WHAT TO DO IN EMERGENCIES

CAUTION! (Continued)
•Do not attempt to tow this vehicle from the front
with sling-type towing equipment. Damage to the
front fascia will result.
•Do not push or tow this vehicle with another
vehicle as damage to the bumper fascia and trans-
axle may result.
If you must use the accessories (wipers, defrosters, etc.)
while being towed, the key must be in the ON position,
not the ACC position. Make certain the transaxle remains
in NEUTRAL.
Front Wheel Drive (FWD)
Your vehicle may be towed under the following condi-
tions:
•The shift lever must be in NEUTRAL.
•The distance to be traveled must not exceed 15 miles
(25 km).
•The towing speed must not exceed 25 mph (40 km/h).
CAUTION!
Exceeding these towing limits may cause a transaxle
failure. Such damage is not covered by the New
Vehicle Limited Warranty. If the transaxle is not
operative, or if the vehicle is to be towed more than
15 miles (25 km), the vehicle must be transported
either with a flatbed truck or with the front wheels
off the ground.
All Wheel Drive (AWD)
Your vehicle may be towed under the following condi-
tions:
•The shift lever must be in NEUTRAL.
6
WHAT TO DO IN EMERGENCIES 399

•The distance to be traveled must not exceed 15 miles
(25 km).
•The towing speed must not exceed 25 mph (40 km/h),
and both front and rear wheels must be on the ground.
CAUTION!
Exceeding these towing limits may cause a transaxle
failure. Such damage is not covered by the New
Vehicle Limited Warranty. If the transaxle is not
operative, or if the vehicle is to be towed more than
15 miles (25 km), the vehicle must be transported on
a flatbed truck.
Towing This Vehicle Behind Another Vehicle With
A Tow Dolly
Front Wheel Drive (FWD)
Rear towing is not recommendedwith the front wheels
on the ground, as transaxle damage can result. If rear towing is the only alternative,
a front end dolly must be
used. Proper towing equipment is necessary to prevent
damage to the vehicle.
All Wheel Drive (AWD)
The manufacturer requires towing your vehicle with all
four wheels OFFthe ground using a flatbed.
CAUTION!
Towing this vehicle using any other method could
result in extensive damage to the transfer case and/or
transmission. Such damage is not covered by the
New Vehicle Limited Warranty.
400 WHAT TO DO IN EMERGENCIES

used to assure most efficient service. MOPARengine air
cleaner filters are a high quality filter and are
recommended.
Maintenance-Free Battery
Your vehicle is equipped with a maintenance-free battery.
You will never have to add water, nor is periodic main-
tenance required.
NOTE: The battery is stored in a compartment that is
located behind the left front fender and is accessible
through the wheel well. The wheel and tire assemble do
not need to be removed to access the compartment.
Remote battery terminals are located in the engine com-
partment for jump-starting. Refer to “Jump-Starting Pro-
cedures” in “What To Do In Emergencies” for further
information.
To access the battery, turn the steering wheel fully to the
right and remove the access panel from the inner fender
shield.
WARNING!
•Battery fluid is a corrosive acid solution and can
burn or even blind you. Do not allow battery fluid
to contact your eyes, skin, or clothing. Do not lean
over a battery when attaching clamps. If acid
splashes in eyes or on skin, flush the area imme-
diately with large amounts of water.
•Battery gas is flammable and explosive. Keep
flame or sparks away from the battery. Do not use
a booster battery or any other booster source with
an output greater than 12 Volts. Do not allow cable
clamps to touch each other.
•Battery posts, terminals, and related accessories
contain lead and lead compounds. Wash hands
after handling.7
MAINTAINING YOUR VEHICLE 413

•If you carry special cargo such as chemicals, fertilizers,
de-icer salt, etc., be sure that such materials are well
packaged and sealed.
•If a lot of driving is done on gravel roads, consider
mud or stone shields behind each wheel.
•Use MOPARTouch Up Paint or equivalent on
scratches as soon as possible. Your authorized dealer
has touch up paint to match the color of your vehicle.
Wheel and Wheel Trim Care
All wheels and wheel trim, especially aluminum and
chrome-plated wheels should be cleaned regularly with a
mild soap and water to prevent corrosion. To remove
heavy soil and/or excessive brake dust, use MOPAR
Wheel Cleaner or equivalent or select a nonabrasive,
non-acidic cleaner. Do not use scouring pads, steel wool,
a bristle brush, or metal polishes. Only MOPAR or
equivalent is recommended. Do not use oven cleaner. Avoid automatic car washes that use acidic solutions or
harsh brushes that may damage the wheels’ protective
finish.
Stain Repel Fabric Cleaning Procedure – If
Equipped
Stain Repel seats may be cleaned in the following man-
ner:
•Remove as much of the stain as possible by blotting
with a clean, dry towel.
•Blot any remaining stain with a clean, damp towel.
•For tough stains, apply MOPAR
Total Clean or a mild
soap solution to a clean, damp cloth and remove the
stain. Use a fresh, damp towel to remove soap residue.
•For grease stains, apply MOPAR Multi-Purpose
Cleaner or equivalent to a clean, damp cloth and
remove the stain. Use a fresh, damp towel to remove
soap residue.
7
MAINTAINING YOUR VEHICLE 437

CavityCartridge
Fuse Mini-
Fuse Description
M20
—15 Amp
Blue
Electronic Vehicle In-
formation Center
(EVIC) – If Equipped,
Interior Lighting,
Steering Wheel
Switches – If
Equipped, Switch
Bank
M21 —20 Amp
Yellow Auto Shut Down
(ASD) #3
M22 —10 Amp
Red Right Horn
M23 —10 Amp
Red Left Horn
M24 —25 Amp
Natural Rear WiperCavity
Cartridge
Fuse Mini-
Fuse Description
M25 —20 Amp
Yellow Fuel Pump/Diesel
Lift Pump
M26 —10 Amp
Red Power MIRRORS
Switch/Drivers Win-
dow Switch
M27
—10 Amp
Red
Steering Column
Lock, Wireless Igni-
tion Node (WIN)/
PEM
M28
—10 Amp
Red
NGC (Powertrain
Control Module)/
Transmission Feed
(Batt)
M29 —10 Amp
Red Occupant Classifica-
tion Module (OCM)
446 MAINTAINING YOUR VEHICLE

CAUTION!
Do not touch the new bulb with your fingers. Oil
contamination will severely shorten bulb life. If the
bulb comes in contact with any oily surface, clean the
bulb with rubbing alcohol.
4. Install the bulb and connector assembly into the
headlamp housing and rotate it
14turn clockwise to lock
it in place.
Front Fog Lamp
NOTE: Turn the steering wheel to the right if replacing
the left front fog lamp or to the left if replacing the right
front fog lamp to allow for easier access to the front of the
wheel well.
1. Remove the fasteners retaining the front lower wheel
well access panel and remove the access panel. 2. Remove the electrical connector from the fog lamp
housing.
3. Remove the bulb from the connector socket and install
the replacement bulb.
7
MAINTAINING YOUR VEHICLE 451

CAUTION!
Do not touch the new bulb with your fingers. Oil
contamination will severely shorten bulb life. If the
bulb comes in contact with an oily surface, clean the
bulb with rubbing alcohol.
4. Install the bulb and connector assembly into the fog
lamp housing and rotate the connector
14turn clockwise
to lock it in place.
5. Reinstall the front lower wheel well access panel and
fasteners.
Tail/Stop Lamp, Rear Turn Signal Lamp, Tail
Lamp, Backup Lamp
The taillamps are a two-piece design. The tail/stop/rear
turn signal lamps are located in the rear corner body
panels. The tail and backup lamps are located in the
liftgate.
Changing the Tail/Stop/Rear Turn Signal Lamp
1. Open the liftgate.
2. Remove the two fasteners from the inboard side of the
taillamp housing.
3. Carefully insert a trim stick (plastic flat-blade tool)
between the body panel and the outboard side of the
taillamp housing with one hand and grasp the flange on
the inboard side of the taillamp housing with the other
hand. Use the trim stick and hand pressure together to
disengage the taillamp housing from the vehicle.
4. Rotate the applicable bulb’s electrical connector
14
turn counterclockwise and remove it from the taillamp
housing.
5. Remove the bulb from the connector socket and install
the replacement bulb.
452 MAINTAINING YOUR VEHICLE