2010 Citroen JUMPY DAG audio
[x] Cancel search: audioPage 184 of 225
9.83
T h e t r a f fi c a n n o u n c e m e n t (TA) is displayed. I do n o t r e c e i v e a n y t r a f fi c information.
T u n e t o a r a d i o s t a t i o n w h i c h b r o a d c a s t s t r a f fi c information. T h e r a d i o s t a t i o n i s n o t p a r t o f t h e r e g i o n a l t r a f fi c i n f o r m a t i o n n e t w o r k .
QUESTION SOLUTION RESPONSE
The quality of reception of the radio station listened to gradually deteriorates or the stored stations do not function (no sound, 87.5 Mhz is displayed...).
The vehicle is too far from the transmitter used b y the station listened to or there is no transmitter in the geographical area th rough which the vehicle is travelling.
The environment (hills, buildings, tunnels, baseme nt car parks...) block reception, including in RDS mode.
The aerial is absent or has been damaged (for exam ple when going through a car wash or into an underground car park).
Activate the RDS function to enable the system to check whether there is a more powerful transmitter in the geographical area.
This phenomenon is normal and does not indicate a failure of the audio equipment.
Have the aerial checked by a CITROËN dealer.
Sound cut-outs of 1 to 2 seconds in radio mode.
During this brief sound cut-out, the RDS searches for any frequency permitting better reception of the station. Deactivate the RDS function if the phenomenon is too frequent and always on the same route.
With the engine off, the audio equipment switches off after a few minutes of use.
When the engine is switched off, the audio equipme nt operating time depends on the battery charge. The switch-off is normal: the audio equipment switches to economy mode and switches off to prevent discharging of the vehicle's battery.
Start the vehicle's engine to increase the battery charge.
The stored stations do not function (no sound, 87.5 Mhz is displayed...)
An incorrect waveband is selected. Press the BAND AST button to return to the waveband (AM, FM1, FM2, FMAST) on which the stations are stored.
The message "the audio system is overheated" appears on the display.
Switch the audio system off for a few minutes to allow the system to cool. In order to protect the installation if the surrounding temperature is too high, the audio equipment switches to an automatic therma l protection mode leading to a reduction of the volume or stopping of the playing of the CD.
Page 185 of 225
9.84
QUESTION SOLUTION RESPONSE
The TRAFFIC INFO box is ticked. However, c e r t a i n t r a f fi c j a m s along the route are not indicated in real time.
On starting, it is several minutes before the system begins to receive the t r a f fi c i n f o r m a t i o n . W a i t u n t i l t h e t r a f fi c i n f o r m a t i o n i s b e i n g r e c e i v e d c o r r e c t l y ( d i s p l a y i n g o f t h e t r a f fi c i n f o r m a t i o n symbols on the map).
In certain countries, only major routes (motorways , ...) are listed for the t r a f fi c i n f o r m a t i o n .
The time taken to calculate a route sometimes seems longer than usual.
This phenomenon is normal. The system is d e p e n d e n t o n t h e t r a f fi c i n f o r m a t i o n a v a i l a b l e .
The performance of the system may slow down tempor arily if a CD is being copied onto the Jukebox at the same time as a route is being calculated.
Wait until the CD has been copied or stop the copying before starting the guidance function.
Does the emergency call function on the NaviDrive work without a SIM card?
No, as certain national regulations impose the presence of a SIM card in order to make an emergency call. Insert a valid SIM card in the slot on the NaviDrive.
My SIM card is not recognised. The NaviDrive accepts 3.3 V SIM cards, the old 5 V and 1.8 V SIM cards are not recognised. Contact your telephone operator.
After changing a wheel, the system loses its location.
The NaviDrive uses the wheel rotation information to improve the GPS l o c a t i n g f u n c t i o n . I f a w h e e l i s c h a n g e d o r d e fl a t e s s u d d e n l y , t h e s y s t e m recalculates the location. For approximately ten mi nutes, this recalculation may affect the quality of the locating function.
Wait until the system has completed its recalculation. The location on the map is incorrect or inaccurate.
The altitude is not displayed. On starting, the initialisation of the GPS may take up to 3 minutes to receive more than 4 satellites correctly. Wait until the system has started up completely. Check that there is a GPS coverage of at least 4 satellites (long press on the MENU button, then select AUDIO/TELEPHONE DIAGNOSTICS, then GPS COVERAGE).
Depending on the geographical environment (tunnel, ...) or the weather, the conditions of reception of the GPS signal may vary. This phenomenon is normal. The system is dependent on the conditions of reception of the GPS signal.
Page 187 of 225
9.41
The MyWay is protected in such a way that it will only operate in your vehicle. If it is to be installed in another v e h i c l e , c o n t a c t a C I T R O Ë N d e a l e r f o r c o n fi g u r a t i o n o f operate in your vehicle. If it is to be installed in another le. If it i
the system.
M y W a y
MULTIMEDIA AUDIO EQUIPMENT/BLUETOOTH TELEPHONE GPS EUROPE BY SD CARD
CONTENTS
Page 188 of 225
9.42
1
5
10
01
2
3 4 6
1 3
11
9
1 4 1 5
7 8 1 2
1 6
1 . Engine not running - Short press: on/off. - Long press: CD pause, mute for the radio. Engine running - Short press: CD pause, mute for the radio. - Long press: reinitialisation of the system.
2 . Volume adjustment.
3 . Access to the "Radio" Menu. Display the list of st
ations.
4 . Access to the "Music" Menu. Display the tracks.
6 . Access to the "Phone" Menu. Display the call list.
7 . Access to the "MODE" Menu. Selection of the successive display of: Radio, Map, NAV (if navigation is in progress), Te lephone (if a conversation is in progress). Long press: display of a black screen (DARK).
8 . Access to the "Navigation" Menu. Display the last destinations.
9 . A c c e s s t o t h e " T r a f fi c " M e n u . D i s p l a y t h e c u r r e n t t r a f fi c a l e r t s .
1 0 . ESC: abandon the operation in progress.
1 1 . CD eject.
1 2 . Selection of the previous/next radio station from the list. Selection of the previous/next MP3 directory. Selection of the previous/next page of a list.
1 3 . Selection of the previous/next radio station. Selection of the previous/next CD or MP3 track. Selection of the previous/next line of a list.
1 4 . Buttons 1 to 6: Selection of the stored radio station. Selection of the CD in the CD changer. Long press: store the current radio station.
1 5 . SD card reader.
1 6 . Dial for selection of the screen display and accor ding to the context of the menu. S h o r t p r e s s : c o n fi r m a t i o n .
FIRST STEPS
M y W a y C O N T R O L P A N E L
3 - 4 . Long press: access to the audio settings: front/rear and left/right balance, bass/treble, equalizer, loudnes s, automatic volume adjustment, initialise the settings.
5 . Access to the "SETUP" Menu. Long press: access to the GPS coverage and the demonstration mode.
Page 194 of 225
9.48
0 3
5
6
7
1
2
3
4
N A V I G A T I O N - G U I D A N C E
ROUTE OPTIONS
Select the "Route dynamics" function. This function gives access to the " T r a f fi c i n d e p e n d e n t " o r " S e m i -dynamic" options.
Select the "Avoidance criteria" function. This function provides access to the AVOID options (motorways, toll roads, ferries).
Turn the dial and select the "Recalculate" function to take into account the route options selected. P r e s s t h e d i a l t o c o n fi r m .
Press the NAV button.
Press the NAV button again or select the "Navigation" Menu function and p r e s s t h e d i a l t o c o n fi r m .
Select the "Route type" function and p r e s s t h e d i a l t o c o n fi r m . T h i s f u n c t i o n allows you to change the route type.
Select the "Route options" function a n d p r e s s t h e d i a l t o c o n fi r m .
" N A V I G A T I O N " M E N U
ROUTE OPTIONS
ROUTE TYPE
ROUTE DYNAMICS
A V O I D A N C E C R I T E R I A
RECALCULATE
The route selected by the MyWay audio/telephone depends directly on the route options. Changing these options may change the route comple tely.
Page 200 of 225
9.54
11
2
3
0 5
SELECTING A STATION
When the current radio station is displayed on the screen, press the dial.
The radio source short-cuts menu appears and providesovides access to the following short-cuts:
Select the function required and press t h e d i a l t o c o n fi r m t o g a i n a c c e s s t o the corresponding settings.
TRAFFIC INFO (TA)
The RDS, if displayed, allows you to continue listening tning to the same station by automatic retuning to alternative freque ncies.ncies. However, in certain conditions, coverage of an RDS station may not y not be assured throughout the entire country as radio stations do not conot cover 100 % of the territory. This explains the loss of reception of the stathe station during a journey.
The external environment (hill, building, tunnel, underground car park...) may interfere with the reception, including in RDS following mode. This ph enomenon is a normal result of the way in which radio waves are transmitted and does not in any way indicate a failure of the audio equipment.
R D S - R E G I O N A L M O D E - T R A F F I C I N F O
Press the RADIO button to display the list of stations received locally sorted in alphabetical order. Select the station required by turning t h e d i a l a n d p r e s s t o c o n fi r m .
While listening to the radio, press one of the buttons to select the previous or next station on the list.
Press one of the buttons on the numeric keypad for moor more than 2 seconds to store the current station. Press the button on the numeric keypad to recall the stothe stored radio station.
RDS
RADIOTEXT
R E G I O N A L P R O G .
AM
RADIO
A long press of one of the buttons starts the automatic search for a station with a lower or higher frequency.
Page 201 of 225
0 6
9.55
MUSIC MEDIA PLAYERS
C D , M P 3 / W M A C D
I N F O R M A T I O N A N D A D V I C E
In order to be able to play a recorded CDR or CDRW, wRW, when recording it is preferable to select the ISO 9660 level 1, vel 1, 2 or Joliet standard. If the disc is recorded in another format it may not be plat be played correctly. It is recommended that the same recording standard is ard is always used for an individual disc, with as low a speed as possible (4ible (4x maximum) for optimum sound quality. In the particular case of a multi-session CD, the Joliet stoliet standard is recommended.
T h e M y W a y w i l l o n l y p l a y a u d i o fi l e s w i t h t h e e x t e n s i o n " . m p 3 " w i t h T h e M y W a y w i l l o n l y p l a y a u d i o fi l e s w i t h t h e e x t e n s i o n " . m p 3 " w i t h a speed of between 8 Kbps and 320 Kbps and the extee extension ".wma" with a speed of between 5 Kbps and 384 Kbps.
The MP3 format, an abbreviation of MPEG 1, 2 & 2.5 A 2.5 Audio Layer 3 and the WMA format, an abbreviation of Windows Medi Media Audio and the property of Microsoft, are audio compression standastandards which p e r m i t t h e r e c o r d i n g o f s e v e r a l t e n s o f m u s i c fi l e s o n a s i n g l e d i s c . p e r m i t t h e r e c o r d i n g o f s e v e r a l t e n s o f m u s i c fi l e s o n a s i n g l e d i s c .
It also supports the VBR (Variable Bit Rate) mode. N o o t h e r t y p e o f fi l e ( . m p 4 , . m 3 u . . . ) c a n b e p l a y e d .
I t i s a d v i s a b l e t o r e s t r i c t fi l e n a m e s t o 2 0 c h a r a c t e r s , w i t h o u t u s i n g o f I t i s a d v i s a b l e t o r e s t r i c t fi l e n a m e s t o 2 0 c h a r a c t e r s , w i t h o u t u s i n g o f special characters (e.g.: " " ? ; ù) to avoid any p laying anying and displaying problems.
Page 203 of 225
1
2
3
4
1
4
0 6
2
3
5
9.57
Connect the portable equipment (MP3/WMA player…) ter…) to the audio sockets (white and red, RCA type) in the glove box usinx using a JACK/RCA audio cable.
Press the MUSIC button then press it again or select the "Music" Menu f u n c t i o n a n d p r e s s t h e d i a l t o c o n fi r m .
Select the AUX music source and p r e s s t h e d i a l t o c o n fi r m . P l a y b e g i n s automatically.
Select the "External device" function and press the dial to activate it.
E X T E R N A L D E V I C E
Insert one or more CDs in the changer. Press the MUSIC button.
Press one of the buttons on the numeric keypad to select the corresponding CD.
Select the CD CHANGER music s o u r c e a n d p r e s s t h e d i a l t o c o n fi r m .
The display and management of the controls is via the pa the portable equipment.
CD CHANGER
Select the SELECT MUSIC function a n d p r e s s t h e d i a l t o c o n fi r m .
U S I N G T H E E X T E R N A L D E V I C E ( A U X )
AUDIO/RCA CABLE NOT SUPPLIED
CD CHANGER
P L A Y I N G A C D ( N O T M P 3 / W M A C O M P A T I B L E )
SELECT MUSIC
Press the MUSIC button again or select the MUSIC MENU function and p r e s s t h e d i a l t o c o n fi r m .
MUSIC MENU
MUSIC MEDIA PLAYERS