2010 Citroen DS3 DAG warning light

Petrol - Diesel instrument panels, manual or automatic gearbox Provided with permanent back-lighting, the instrument panel groups together the vehicle's dials and indic ator and warning lamps.
1. Rev counter. Indicates the speed of rotation ofthe engine (x 1 000 rpm).
2. Vehicle speed. Indicates the current speed of the moving vehicle (mph or km/h). 3. Engine coolant temperature. Indicates the temperature of the engine coolant liquid.
Dials
7. Lighting rheostat button. Adjusts the level of the instrument and controls illumination and the interior mood
lighting.
4. Display screen.5. Fuel level. Indicates the quantity of fuel remaining in
the tank. 6. Display management button Alternates display between range and trip mileage recorder. Ser vicing information. Resets the selected function to zero(trip distance recorder or ser vice indicator).
For more information, refer to the paragraph relating to the button or function and its associated display.

Visual indicators informing the driver that a system is in operation (operation or deactivation indicator lamps) or ofthe occurrence of a fault (warning lamp).
Indicator and warning lamps
When the ignition is switched on
Certain warning lamps come on for a few seconds when the vehicle's ignition is switched on. When the engine is star ted, these same warning lamps should switch off. If they remain on, before moving off, refer tothe information on the warning lamp concerned.
Associated warnings
The switching on of cer tain warning lamps may be accompanied by an audible signal and a message on the multifunction screen.
The warning lamps may come on continuously (fixed) or flash. Cer tain warning lamps may come on in two different modes. Only by relating the type of lighting to the operating status of the vehicle can it
be ascer tained whether the situation is normal or whether a fault has occurred.
The passenger airbag system operation lamp stays on for about a minute after switching on the ignition, even afterthe engine has star ted.

27Monitoring
Operation indicator lamps
If one of the following indicator lamps comes on, this confirms that the corresponding system has come into o peration.
Warning lampis onCauseAction/Obser vations
Left-hand direction indicatorrr flashing with buzzer. The lighting stalk is pushed down.
Right-hand direction indicatoratortor flashing with buzzer. The lighting stalk is pushed up.
Sidelamps fixed. The lighting stalk is in the "Sidelamps" position.
Dipped beam headlamps fixed. The lighting stalk is in the "Dipped beam headlamps" position.
Main beam headlamps fixed. The lighting stalk is pulled towards you. Pull the stalk to return to dipped beam headlamps.
Front foglamps fixed. The front foglamps are switched on. Turn the ring on the stalk rear wards twice to switch off the front foglamps.
Rear foglamps fixed. The rear foglamps are switched on. Turn the ring on the stalk rear wards to switch off the rear foglamps.

Hazard warning lamps flashing with buzzer. The hazard warning lamps switch, located on the dashboard, has been pressed.
The left-hand and right-hand direction indicators a nd their associated indicator lamps flash simultaneously.

Warning lampis onCauseAction/Obser vations
Diesel engine pre-heating fixed. The ignition switch is at the 2nd position (ignition on). Wait until the warning lamp goes off before star ting. The period of illumination of the warning lamp is determined by the climatic conditions (up to about thir ty seconds in extreme climatic conditions). If the engine does not star t, switch the ignition off and
then on, wait until the warning lamp goes off again, then star t the engine.
Parking brake fixed. The parking brake is applied or not properly released. Release the parking brake to switch off the warning lamp, keeping your foot on the brake pedal. Obser ve the safety. For fur ther information on the parking brake, refer t o the "Driving" section.

Stop & Star t
fixed. The Stop & Star t system has put the engine in STOP mode at a vehicle stop (traffic lights, traffic jam, or other...).
The warning lamp goes off and the engine restar ts automatically in START mode, as soon as you want to move off.
flashes for a few seconds, then goes
off.
STOP mode is temporarily unavailable.
or START mode is invoked automatically.
Refer to "Driving - § Stop & Star t" for special cases with STOP mode and START mode.

With the engine running, when the needle is: - in zone A , the temperature is correct,
- in zone B , the temperature is too high; the central STOP warning lamp and the maximum temperature warning lamp 1 light up in red, accompanied by an audible signal and a message on the multifunction screen. You must stop as soon as it is safe to do so. Wait a few minutes before switching off the engine. Consult a CITROËN dealer.
Coolant temperature
indicator
After driving for a few minutes, the temperature and pressure in the cooling system increase.
To top up the level:  wait for the engine to cool down,  unscrew the cap by two turns to allowthe pressure to drop,  when the pressure has dropped, remove the cap,  top up the level to the "MA X" mark.

lamps and flashing of the direction indicators for a few seconds.
Locating your vehicle
 Press the closed padlock to
locate your locked vehicle in a car park.
Anti-theft protection
Electronic engine immobiliser
The key contains an electronic chip which has a special code. When the ignition is switched on, this code must be recognised in order for star ting to be possible. This electronic engine immobiliser locks the engine management system a few minutes after the ignition is switched off and prevents star ting of the engine by anyone who does not have the key.
In the event of a malfunction, you are informed by lighting of this warning lamp, an audible signal and a message on the multifunction screen. In this case, your vehicle does not star t; contact a CITROËN dealer as soon as possible.
- Position 1: Stop - Position 2: Ignition - Position 3: Star ting
Ignition switch

lamps and flashing of the direction indicators for a few seconds.
Locating your vehicle
 Press the closed padlock to
locate your locked vehicle in a car park.
Anti-theft protection
Electronic engine immobiliser
The key contains an electronic chip which has a special code. When the ignition is switched on, this code must be recognised in order for star ting to be possible. This electronic engine immobiliser locks the engine management system a few minutes after the ignition is switched off and prevents star ting of the engine by anyone who does not have the key.
In the event of a malfunction, you are informed by lighting of this warning lamp, an audible signal and a message on the multifunction screen. In this case, your vehicle does not star t; contact a CITROËN dealer as soon as possible.
- Position 1: Stop - Position 2: Ignition - Position 3: Star ting
Ignition switch

Following disconnection of the vehicle battery,
replacement of the remote control battery or in the event of a remote control malfunction, you can no longer unlock, lock or locate your vehicle.  First of all, use the key in the lock to unlock or lock your vehicle.  Then, reinitialise the remote control. If the problem persists, contact a CITROËN dealer as soon as possible.
Remote control problem
Reinitialisation
 Switch off the ignition.  Turn the key to position 2 (Ignition) .  Press the closed padlock immediately for a few seconds.  Switch off the ignition and remove the key from the ignition switch. The remote control is fully operational again.
Changing the battery
Battery ref.: CR1620/3 volts. This replacement battery is available from CITROËN dealers.
 Maintain pressure on lug A and remove the chrome finisher by sliding it off at 45°.  Unclip the casing by inser ting a coin at the
notch and rotating.  Slide the flat battery out of its location.  Slide the new battery into its location obser ving the original direction.  Clip the casing in place, then the chrome finisher.  Reinitialise the remote control.
If the battery is flat, you are informed by lighting of this warning lamp in the instrument panel, an audible signal and a message on the multifunction screen.
 Unfold the key.  Release the chrome finisher by pressing on
lug A .