Page 6 of 253
Monitoring
Foot on the brake pedal fixed. With an automatic gearbox, you have forgotten to press the brake pedal to come out of the P postion.
With the engine running, before releasing the parking brake you must press the brake pedal to unlock thethe automatic gear selector lever and come out ofthe P position.
Automatic wiping fixed. The wiper control is pushed downwards. Automatic front wiping is activated.
Passenger's airbag system fixed. The control switch, located in the glove box, is in the " ON " position. The passenger's front airbag is activated. In this case, do not install a rear-facing child seat.
Turn the control switch to the " OFF " position to deactivate the front passenger's airbag. In this case you can install a rear-facing child seat. The passenger's airbag system is automatically put into ser vice on star ting the vehicle (" ON " position).
Warning lampis onCauseAction/Obser vations
Page 9 of 253
fixed, associated with
the STOP warning lamp.
The braking system fluid level is too
low.
You must stop as soon as it is safe to do so.
Top up with brake fluid recommended by CITROËN. If the problem persists, have the system checked by a CITROËN dealer.
+ fixed, associated with the STOP and ABS warning lamp.
The electronic brake force distribution (EBFD) system has a fault. You must stop as soon as it is safe to do so. Have it checked by a CITROËN dealer.
Warning lampis onCauseAction/Obser vations
Anti-lock Braking System (ABS) fixed. The anti-lock braking system has a fault. The vehicle retains conventional braking. Drive carefully at reduced speed and contact a
CITROËN dealer without delay.
Dynamic stability control (ESP/ASR)
flashing. The ESP/ASR regulation is active. The system optimises traction and improvesthe directional stability of the vehicle.
fixed. Unless it has been deactivated with the indicator lamp on the button on, the ESP/ASR system is faulty.
Have it checked by a CITROËN dealer.
Page 15 of 253
A few seconds after the ignition is switched on, the distance recorder resumes its normal operation. The spanner remains on .
The distance remaining may be weighted by the time factor, depending on the driver's driving habits.
Therefore, the spanner may also come on if you have exceeded the two year ser vice inter val.
Service indicator zero reset
After each ser vice, the ser vice indicator must be reset to zero. The procedure for resetting to zero is as follows: switch off the ignition, press and hold the trip distance recorder zero reset button, switch on the ignition; the distance recorder display begins a countdown, when the display indicates "=0" , release the button; the spanner disappears.
Following this operation, if you wish to disconnect the battery, lock the vehicle and wait at least five minutes for the zero reset to be taken into account.
Retrieving the service information
You can access the ser vice information at any time. Press the trip distance recorder zero reset button. The ser vice information is displayed for a few seconds, then disappears.
Service overdue
For a few seconds after the ignition is switched on, the spanner flashes to indicate that the ser vice must be carried out as soon as possible. Example: the service is overdue by 300 miles (km). For a few seconds after the ignition is switched on, the display indicates:
Page 17 of 253
System which measures the total distance travelled by the vehicle during its life. The total and trip distances are displayed for thir ty seconds when the ignition is switched off, when the driver's door is opened and when the vehicle is locked or unlocked.
Total distance recorder
System which measures a distance travelled during a day or other period since it was reset to zero by the driver. With the ignition on, press the button until zeros appear.
Trip distance recorder
System for manual adjustment of the brightness of the instruments and controls in relation tothe exterior brightness.
Lighting rheostat
Activation
When the lighting is on: press the button to change the brightness of the instruments and controls, when the level of brightness required is reached, release the button.
Deactivation
When the lighting is off, or in day mode on vehicles fitted with daytime running lamps, pressing the button does not have any effect.
Page 48 of 253
R e m o v i n g t h e c a r t r i d g e
Press the dial and turn it a quar ter of a turn anti-clockwise. Remove the car tridge. Refit its sealing case.
F i t t i n g t h e c a r t r i d g e
Remove the car tridge from the sealing case. Install the car tridge (flower at top left). Press the dial and turn it a quar ter of a turn clockwise.
Page 51 of 253
75Comfort
A c c e s s t o t h e r e a r s e a t s
Pull the control upwards to fold the seat back and move the seat for ward. When put back in place, the seat returns to its initial position.
No person or object should prevent the seat slide from returning to its initial position; the return to this position is necessary for longitudinal locking. Check that the seat belt has reeled in correctly so as to not impede access to the rear seats for passengers.
Heated seats control
With the engine running, the front seats can be heated separately. Use the adjustment dial, placed on the side of each front seat, to switch on and select the level of heating required: 0: Off. 1 : Low. 2 : Medium. 3 : High.
G r a b h a n d l e
This easy to use handle, located at the top of the side trim: - provides a means of suppor t for the outer rear passengers when moving, - provides a hand hold to ease access to the rear seats, - facilitates exit from the rear seats.
Page 53 of 253
77Comfort
These have one position for use (up) and a stowed position (down). They can also be removed. To remove a head restraint: release the backrest using control 1 , tilt the backrest 2 slightly for wards,
pull the head restraint upwards to the stop, then, press the lug A .
R e a r h e a d r e s t r a i n t s
Never drive with the head restraints removed; they must be in place and correctly adjusted.
Steering wheel adjustment
W h e n s t a t i o n a r y , pull the control lever to W h e n s t a t i o n a r y W h e n s t a t i o n a r yrelease the steering wheel. Adjust the height and reach to suit your driving position. Push the control lever to lock the steering wheel.
As a safety precaution, these operations should only be carried out while the vehicle is stationary.
Page 54 of 253
77Comfort
These have one position for use (up) and a stowed position (down). They can also be removed. To remove a head restraint: release the backrest using control 1 , tilt the backrest 2 slightly for wards,
pull the head restraint upwards to the stop, then, press the lug A .
R e a r h e a d r e s t r a i n t s
Never drive with the head restraints removed; they must be in place and correctly adjusted.
Steering wheel adjustment
W h e n s t a t i o n a r y , pull the control lever to W h e n s t a t i o n a r y W h e n s t a t i o n a r yrelease the steering wheel. Adjust the height and reach to suit your driving position. Push the control lever to lock the steering wheel.
As a safety precaution, these operations should only be carried out while the vehicle is stationary.
