2010 CITROEN C4 PICASSO window
[x] Cancel search: windowPage 60 of 352
Downloaded from www.Manualslib.com manuals search engine III
58
COMFORT
MANUAL AIR CONDITIONING
The air conditioning system oper-
ates with the engine running.
A. DRIVER'S CONTROL PANEL
1. Adjustment of the air fan
speed
The air fan adjustment only operates
when the engine is running.
To adjust the air fl ow, press button 1
:
to increase the fl ow of air,
to decrease the fl ow of air. The level of air fl ow is shown by the
progressive lighting of the warning
lamps depicting the fan blades 1
.
By reducing the fl ow to minimum,
you deactivate the air conditioning
system (OFF).
To maintain an acceptable level of
comfort in the passenger compart-
ment, you should not leave this con-
trol too long in the OFF position.
2. Adjustment of air
distribution
)
Press button 2
to make the dis-
play run through the different
types of air distribution.
The air distribution chosen
is shown by the lighting of
the corresponding warning
lamps on the display 2
.
3. Mode of adjustment
of temperature for the
passenger
)
Press button 3
to have indepen-
dent passenger control of cabin
air temperature. The warning
lamp goes off.
While the passenger is adjusting tem-
perature, the warning lamp comes on.
4. Air recirculation
This control is for isolating disagree-
able odours or fumes coming from
outside.
)
Press button 4
to cut off the intake
of outside air and to activate recir-
culation of the air in the passenger
compartment. The warning lamp
comes on.
Avoid the extended use of air re-
circulation (risk of deterioration
of air quality and misting).
)
Press button 4
again to allow the
intake of exterior air. The warning
lamp goes off.
5. Air conditioning
The air fan control (adjusting the fl ow
of air) has to be activated in order for
air conditioning to be obtained.
)
Press button 5
. The warning
lamp comes on.
To be effective,
the air condi-
tioning should be operated only
with the windows closed.
If your vehicle is not equipped with
air conditioning, you will have the
same control panel but without the
A/C
button.
Page 61 of 352
Downloaded from www.Manualslib.com manuals search engine III
59
COMFORT
6. Demisting/defrosting the
rear screen
This function operates only if the en-
gine is running.
)
Press button 6
to activate/de-
activate the electric demisting/
defrosting of the rear screen and
door mirrors. The warning lamp
comes on.
7. Rapid demisting/defrosting
of front and rear windows
and door mirrors
)
Press button 7
. The warning
lamp comes on.
This function simultaneously acti-
vates:
- front demisting/defrosting,
- optimum fl ow of air,
- intake of exterior air,
- demisting/defrosting of door mir-
rors and heated rear screen,
- air conditioning, if necessary.
To stop the function, press button 7
again.
8. Adjustment of the fan air
temperature
This control is for adjusting the tem-
perature of the air in the passenger
compartment. It can be used in cold
weather as well as in hot weather,
provided the air conditioning is ac-
tive.
The adjustment of the temperature
is continuous and progressive start-
ing from left to right.
Adjustment of temperature
)
Press button 9
to take control of
the temperature. The warning
lamp comes on.
)
Rotate button 10
to adjust your
temperature.
The adjustment of the temperature
is continuous and progressive start-
ing from left to right. The demisting/defrosting
switches off automatically
to prevent excessive con-
sumption of power.
B. PASSENGER'S CONTROL
PA N E L
Page 65 of 352
Downloaded from www.Manualslib.com manuals search engine III
63
COMFORT
9. Rapid demisting/defrosting
of the front and rear
windows
- Press button 9
. The warning
lamp comes on.
This function gives a rapid
demisting/defrosting of the
vehicle simultaneously with:
- front demisting/defrosting at op-
timum temperature,
- optimum air fl ow,
- intake of exterior air,
- demisting/defrosting of the door
mirrors and rear screen,
- air conditioning, if necessary.
Press button 9
again or " AUTO"
to stop the function. Demisting/
defrosting of the door mirrors and
rear screen remains activated.
10. Air conditioning
)
Press button 10
to activate the
air conditioning.
The A/C
warning lamp comes on.
B. PASSENGER CONTROL PANELS
11. Front passenger
The front passenger can adjust their
temperature control independently
at any time by pressing buttons +
and -
.
The front passenger con-
trols the adjustment of their
own temperature.
The temperature setting for
the passenger is aligned
with that for the driver.
12. Rear passengers (right/left)
By default, in AUTO
position, the adjust-
ment of the air fl ow is
aligned on the front
ventilation.
)
Rotate the button
to decrease or in-
crease the air fl ow.
You can adjust the air fl ow only if this
is enabled by the driver (see button 6
of the driver’s control panel).
With Stop & Start, when demist-
ing has been activated, the STOP
mode is not available.
Page 81 of 352
Downloaded from www.Manualslib.com manuals search engine IV
79
ACCESS
Normal locking using the key
)
Turn the key to the right in the
driver's door lock to lock the ve-
hicle. To allow long objects to be carried,
the vehicle can be locked from the
inside, using the central locking
control on the dashboard, even if
the tailgate or rear screen is open.
When the vehicle is locked, if it is
unlocked inadvertently, it will lock
itself again automatically after thirty
seconds unless a door is opened.
When closing the windows and/or
panoramic sunroof blind using the
remote control, you must ensure
that no one prevents them from
closing correctly.
The folding and unfolding of the
door mirrors using the remote
control can be deactivated by a
CITROËN dealer or a qualifi ed
workshop.
Deadlocking using the remote
control
)
Press the closed pad-
lock to lock the vehicle
completely or press the
closed padlock for more
than two seconds to
close the windows and
the panoramic sunroof
blind automatically in
addition to locking.
)
Press the closed padlock again
within fi ve seconds to deadlock
the vehicle.
Locking the vehicle
Normal locking using the remote
control
)
Briefl y press the closed
padlock to lock the ve-
hicle.
)
Make a long press on the closed
padlock to lock the vehicle and
also close the windows and the
panoramic sunroof blind.
Locking is confi rmed by fi xed light-
ing of the direction indicators for ap-
proximately two seconds.
According to version, the door mir-
rors fold at the same time.
Locking also triggers the timed
switching on of the exterior side
spotlamps and the guide-me-home
lighting, if this is activated.
If one of the doors, the rear screen
or the boot is still open, the central
locking does not take place.
Page 82 of 352
Downloaded from www.Manualslib.com manuals search engine IV
80
ACCESS
Deadlocking using the key
)
Turn the key to the right in the driv-
er's door lock to lock the vehicle
completely and hold it in this posi-
tion for more than two seconds to
close the windows automatically
in addition to locking.
)
Turn the key to the right again
within fi ve seconds to deadlock
the vehicle.
Deadlocking renders the exterior and
interior door controls inoperative.
It also deactivates the manual cen-
tral control button.
Therefore, never leave anyone in-
side the vehicle when it is dead-
locked. Deadlocking also triggers the timed
illumination of the exterior side spot
lamps and guide-me-home lighting,
if this is activated.
)
First press this button to fold the
key.
If you do not press the button when
folding the key, there is a risk of
damage to the mechanism.
Locating your vehicle
This function allows you to identify
your vehicle from a distance, espe-
cially when the light is poor. Your ve-
hicle must be locked.
)
Press the closed padlock on the
remote control.
This will bring on the courtesy lamps
and exterior side spotlamps, as well
as fl ashing the direction indicators
for a few seconds.
Remote operation of lighting
Anti-theft protection
Electronic engine immobiliser
The key contains an electronic chip
which has a special code. When the
ignition is switched on, this code
must be recognised in order for
starting to be possible.
This electronic engine immobiliser
locks the engine management sys-
tem a few minutes after the ignition
is switched off and prevents starting
of the engine by anyone who does
not have the key.
In the event of a fault,
you are informed by il-
lumination of this warn-
ing lamp, an audible
signal and a message in the screen.
In this case, your vehicle will not
start; contact a CITROËN dealer as
soon as possible.
Keep safely the label attached to the
keys given to you on acquisition of
the vehicle.
Folding the key
A press on this button
brings on the temporary
illumination of sidelamps,
dipped beam headlamps,
number plate lamps and
the exterior side spotlamps located
underneath the door mirrors.
A second press before the end of the
timed period cancels the command.
Deadlocking is confi rmed by fi xed
lighting of the direction indicators for
approximately two seconds.
According to version, the door mir-
rors fold at the same time.
Page 86 of 352
Downloaded from www.Manualslib.com manuals search engine IV
84
ACCESS
ALARM
System which protects and provides
a deterrent against theft and break-
ins. It provides the following types of
monitoring.
- Exterior perimeter
The system checks for opening of
the vehicle.
The alarm is triggered if anyone tries
to open a door, the boot, the bonnet...
- Interior volumetric
The system checks for any variation
in the volume in the passenger com-
partment.
The alarm is triggered if anyone
breaks a window, enters the pas-
senger compartment or moves in-
side the vehicle.
Self-protection function
The system checks for the putting
out of service of its components.
The alarm is triggered if the battery,
the central control or the wires of the
siren are put out of service or dam-
aged.
Locking the vehicle with full
alarm system
Activation
)
Switch off the ignition and get out
of the vehicle.
)
Press the locking button on the
remote control.
Deactivation
)
Press the unlocking button on
the remote control.
The alarm system is deactivated: the
indicator lamp in the button goes off.
If an opening (door, boot...) is not
closed fully, the vehicle is not locked
but the exterior perimeter monitor-
ing will be activated after a delay of
45 seconds at the same time as the
interior volumetric monitoring.
The monitoring system is active: the
indicator lamp in the button fl ashes
once per second.
After the locking button on the re-
mote control is pressed, the exterior
perimeter monitoring is activated
after a delay of 5 seconds and the
interior volumetric monitoring after a
delay of 45 seconds.
For all work on the alarm system,
contact a CITROËN dealer or a
qualifi ed workshop.
Page 87 of 352
Downloaded from www.Manualslib.com manuals search engine IV
85
ACCESS
Locking the vehicle with
exterior perimeter monitoring
only
Deactivate the interior volumetric
monitoring to avoid unwanted trig-
gering of the alarm in certain cases
such as:
- leaving a pet in the vehicle,
- leaving a window partially open,
- washing your vehicle,
To be effective, this deactivation
must be carried out each time the
ignition is switched off.
Deactivation of the interior
volumetric monitoring
)
Switch off the ignition.
)
Within ten seconds, press the
button until the indicator lamp is
on continuously.
)
Get out of the vehicle.
)
Press the locking button on the
remote control immediately.
The exterior perimeter monitoring
alone is activated: the indicator lamp in
the button fl ashes once per second.
Triggering of the alarm
The monitoring functions remain
active until the alarm has been trig-
gered eleven times in succession.
When the vehicle is unlocked using
the remote control, rapid fl ashing
of the indicator lamp in the button
informs you that the alarm was trig-
gered during your absence. When
the ignition is switched on, this
fl ashing stops immediately.
Failure of the remote control
To deactivate the monitoring func-
tions:
Locking the vehicle without
activating the alarm
Malfunction
Automatic activation *
)
Lock or deadlock the vehicle us-
ing the key in the driver's door
lock.
When the ignition is switched on, fi xed il-
lumination of the indicator lamp in the but-
ton indicates a malfunction of the system.
Have it checked by a CITROËN dealer or
a qualifi ed workshop.
2 minutes after the last door or the
boot is closed, the system is activat-
ed automatically.
)
To avoid triggering the alarm on
entering the vehicle, fi rst press
the unlocking button on the re-
mote control.
)
Unlock the vehicle using the key
in the driver's door lock.
)
Open the door; the alarm is trig-
gered.
)
Switch on the ignition; the alarm
stops. The indicator lamp in the
button goes off.
This is indicated by sounding of the
siren and fl ashing of the direction in-
dicators for thirty seconds.
Reactivation of the interior
volumetric monitoring
)
Press the unlocking button on the
remote control to deactivate the
exterior perimeter monitoring.
)
Press the locking button on the
remote control to activate all the
monitoring functions.
The indicator lamp in the button
again fl ashes once per second.
*
According to country.
Page 88 of 352
Downloaded from www.Manualslib.com manuals search engine IV
86
ACCESS
ELECTRIC WINDOWS
System intended to open or close a
window manually or automatically.
Fitted with a safety anti-pinch system
and a system for deactivation in the
event of misuse of the rear controls.
1.
Driver's electric window
control.
2.
Passenger's electric window
control.
3.
Rear right electric window
control.
4.
Rear left electric window
control.
5.
Deactivation of the rear
electric window and door
controls.
One-touch electric windows
There are two options:
- automatic mode
)
Press or pull the control
fi rmly. The window opens or
closes fully when the control is
released.
)
Pressing the control again
stops the movement of the
window.
The electric window controls re-
main operational for approximately
45 seconds after the ignition is
switched off or until the vehicle is
locked after a door is opened.
If one of the passenger windows
cannot be operated from the driv-
er's door control panel, carry out
the operation from the control
panel of the passenger door con-
cerned, and vice versa.
Safety anti-pinch
When the window rises and meets
an obstacle, it stops and partially
lowers again.
If the window cannot be closed (for
example, in the presence of ice),
immediately after the movement is
reversed:
)
press and hold the control until
the window opens fully,
)
then pull the control immediate-
ly and hold it until the window
closes,
)
continue to hold the control for
approximately one second after
the window has closed.
The safety anti-pinch function
is not operational during these
operations.
- manual mode
)
Press or pull the control gently.
The window stops when the
control is released.