2010 Citroen C3 brake
[x] Cancel search: brakePage 4 of 205
1
MONITORING
Front
foglamps fi x e d . The front foglamps are
switched on. Turn the ring on the stalk rearwards twice to
switch off the front foglamps.
Rear
foglamps fi x e d . The rear foglamps are
switched on. Turn the ring on the stalk rearwards to switch off
the rear foglamps.
Diesel engine
pre-heating fi x e d . The ignition switch is at the
2nd position (ignition on).
Wait until the warning lamp has switched off befor
e starting.
The duration for which the warning lamp is on is
determined by the climatic conditions.
Parking brake fi x e d . The parking brake is
applied or not properly
released. Release the parking brake to switch off the
warning lamp, keeping your foot on the brake
pedal.
Observe the safety recommendations.
For further information on the parking brake, refer
to the "Driving" section.
Warning lamp is on Cause Action/Observations
Engine
coolant
temperature fi x e d b l u e . On starting the engine, it
indicates that the engine is
cold. After a few minutes driving, it swiches off to
indicate that the engine temperature is normal.
In order to protect your engine, avoid driving too
hard until the warning lamp has switched off.
Foot on the
brake pedal fi x e d . With an automatic gearbox,
you have forgotten to press
the brake pedal to come out
of the
P postion. With the engine running, before releasing the
parking brake you must press the brake pedal to
unlock the the automatic gear selector lever and
come out of the
P position.
Automatic
wiping fi x e d . The wiper control is pushed
downwards. Automatic front wiping is activated.
Main beam
headlamps fi x e d . The lighting stalk is pulled
towards you. Pull the stalk to return to dipped beam
headlamps.
Page 6 of 205
1
MONITORING
Warning lamps
When the engine is running or the vehicle is
being driven, the switching on of one of the fol-
lowing warning lamps indicates a fault which
requires action on the part of the driver.
Any fault resulting in the switching on of a warni ng lamp must be investigated
further by reading the associated message on the mu ltifunction screen.
If you encounter any problems, do not hesitate to contact a CITROËN dealer.
Warning lamp is on Cause Action/Observations
STOP
fi x e d , a s s o c i a t e d
with another warning
lamp and
accompanied by
an audible signal.
It is associated with the
braking system or the
engine coolant temperature. Stop as soon as it is safe to do so.
Park, switch off the ignition and call a CITROËN
dealer.
Service temporarily.
A minor fault has occurred
for which there is no
s p e c i fi c w a r n i n g l a m p . Identify the fault by reading the message shown
on the screen, such as, for example:
- the engine oil level,
- the screenwash level,
- the remote control battery,
- s a t u r a t i o n o f t h e p a r t i c l e e m i s s i o n fi l t e r
(Diesel).
For any other faults, contact a CITROËN dealer.
fi x e d . A major fault has occurred
for which there is no
s p e c i fi c w a r n i n g l a m p . Identify the fault by reading the message shown
on the screen and contact a CITROËN dealer.
Braking fi x e d .
The braking system
fl u i d l e v e l h a s d r o p p e d
s i g n i fi c a n t l y . T o p u p w i t h b r a k e fl u i d r e c o m m e n d e d b y
CITROËN.
If the problem persists, have the system checked
by a CITROËN dealer.
+
fi x e d , a s s o c i a t e d with the ABS
warning lamp. The electronic brake force
distribution (EBFD) system
has a fault. Have it checked by a CITROËN dealer.
Page 91 of 205
8
SAFETY
BRAKING ASSISTANCE
SYSTEMS
G r o u p o f s u p p l e m e n t a r y s y s t e m s w h i c h
h e l p y o u t o o b t a i n o p t i m u m b r a k i n g i n
c o m p l e t e s a f e t y i n e m e r g e n c y s i t u a -
tions:
- a n t i - l o c k b r a k i n g s y s t e m ( A B S ) ,
- e l e c t r o n i c b r a k e f o r c e d i s t r i b u t i o n ( E B F D ) ,
- e m e r g e n c y b r a k i n g a s s i s t a n c e ( E B A ) .
Anti-lock braking system
and electronic brake force
distribution
L i n k e d s y s t e m s w h i c h i m p r o v e t h e s t a b i l i t y
a n d m a n o e u v r a b i l i t y o f y o u r v e h i c l e w h e n
b r a k i n g , i n p a r t i c u l a r o n p o o r o r s l i p p e r y
s u r f a c e s .
Activation
T h e a n t i - l o c k b r a k i n g s y s t e m c o m e s
i n t o o p e r a t i o n a u t o m a t i c a l l y w h e n t h e r e
is a risk of wheel lock.
N o r m a l o p e r a t i o n o f t h e A B S m a y m a k e
itself felt by slight vibration of the brake
pedal.
W h e n b r a k i n g i n a n e m e r g e n c y ,
p r e s s v e r y fi r m l y w i t h o u t r e l e a s i n g
t h e p r e s s u r e . Operating fault
I n e i t h e r c a s e , c o n t a c t a C I T R O Ë N
dealer.
I f t h i s w a r n i n g l a m p c o m e s o n ,
a c c o m p a n i e d b y a n a u d i b l e
s i g n a l a n d a m e s s a g e o n t h e
m u l t i f u n c t i o n s c r e e n , i t i n d i c a t e s
a m a l f u n c t i o n o f t h e a n t i - l o c k b r a k i n g
s y s t e m w h i c h c o u l d r e s u l t i n l o s s o f
control of the vehicle when braking.
I f t h i s w a r n i n g l a m p c o m e s o n ,
together with the STOP and
ABS w a r n i n g l a m p s , a c c o m p a -
n i e d b y a n a u d i b l e s i g n a l a n d a
m e s s a g e o n t h e m u l t i f u n c t i o n s c r e e n , i t
i n d i c a t e s a m a l f u n c t i o n o f t h e e l e c t r o n -
i c b r a k e f o r c e d i s t r i b u t i o n w h i c h c o u l d
r e s u l t i n l o s s o f c o n t r o l o f t h e v e h i c l e
when braking.
You
must
stop as soon as it is safe
to do so.
W h e n r e p l a c i n g w h e e l s ( t y r e s
a n d r i m s ) , e n s u r e t h a t t h e y
c o n f o r m t o t h e m a n u f a c t u r e r ' s
r e c o m m e n d a t i o n s . Emergency braking assistance
S y s t e m w h i c h , i n a n e m e r g e n c y , e n -
a b l e s y o u t o o b t a i n t h e o p t i m u m b r a k i n g
p r e s s u r e m o r e q u i c k l y , t h u s r e d u c i n g t h e
stopping distance.
Activation
It is triggered by the speed at which the
brake pedal is pressed.
T h e e f f e c t o f t h i s i s a r e d u c t i o n i n t h e
resistance of the pedal and an increase
i n b r a k i n g e f fi c i e n c y .
W h e n b r a k i n g i n a n e m e r g e n c y ,
p r e s s fi r m l y w i t h o u t r e l e a s i n g
t h e p r e s s u r e .
Page 92 of 205
8
SAFETY
TRAJECTORY CONTROL
SYSTEMS
Anti-skid regulation (ASR) and
electronic stability programme
(ESP)
T h e a n t i - s k i d r e g u l a t i o n ( a l s o k n o w n
a s T r a c t i o n C o n t r o l ) o p t i m i s e s t r a c t i o n
t o p r e v e n t s k i d d i n g o f t h e w h e e l s , b y
acting on the brakes of the driving
wheels and on the engine.
T h e e l e c t r o n i c s t a b i l i t y p r o g r a m m e a c t s
o n t h e b r a k e o f o n e o r m o r e w h e e l s a n d
on the engine to keep the vehicle on the
t r a j e c t o r y r e q u i r e d b y t h e d r i v e r , w i t h i n
t h e l i m i t s o f t h e l a w s o f p h y s i c s .
Activation
T h e s e s y s t e m s a r e a c t i v a t e d a u t o m a t i -
c a l l y e a c h t i m e t h e v e h i c l e i s s t a r t e d .
T h e y c o m e i n t o o p e r a t i o n i n t h e e v e n t
o f a g r i p o r t r a j e c t o r y p r o b l e m . T h i s i s i n d i c a t e d b y fl a s h i n g o f
t h i s w a r n i n g l a m p o n t h e i n s t r u -
m e n t p a n e l . Deactivation
I n e x c e p t i o n a l c o n d i t i o n s ( s t a r t i n g a
v e h i c l e w h i c h i s b o g g e d d o w n , s t u c k
i n s n o w , o n s o f t g r o u n d . . . ) , i t m a y b e
advisable to deactivate the ASR and
E S P s y s t e m s , s o t h a t t h e w h e e l s c a n
m o v e f r e e l y a n d r e g a i n g r i p .
Press the "ESP OFF" b u t t o n , l o c a t e d
on the left below the steering wheel.
I f t h i s w a r n i n g l a m p c o m e s o n i n t h e i n s t r u -
m e n t p a n e l a n d t h e i n d i c a t o r l a m p o n t h e
b u t t o n c o m e s o n , t h i s i n d i c a t e s t h a t t h e
A S R a n d E S P s y s t e m s a r e d e a c t i v a t e d .
Reactivation
T h e s e s y s t e m s a r e r e a c t i v a t e d a u t o m a t -
i c a l l y e a c h t i m e t h e i g n i t i o n i s s w i t c h e d
b a c k o n o r f r o m 3 0 m p h ( 5 0 k m / h ) .
Press the "ESP OFF" b u t t o n a g a i n
t o r e a c t i v a t e t h e m m a n u a l l y . Operating fault
I f t h i s w a r n i n g l a m p c o m e s o n ,
a c c o m p a n i e d b y a n a u d i b l e s i g -
n a l a n d a m e s s a g e o n t h e m u l t i -
f u n c t i o n s c r e e n , t h i s i n d i c a t e s a
m a l f u n c t i o n o f t h e s e s y s t e m s .
H a v e t h e s y s t e m s c h e c k e d b y a C I T R O Ë N
dealer.
T h e E S P / A S R s y s t e m s o f f e r e x -
c e p t i o n a l s a f e t y i n n o r m a l d r i v i n g ,
b u t t h i s s h o u l d n o t e n c o u r a g e t h e
driver to take extra risks or drive at
high speed.
T h e c o r r e c t f u n c t i o n i n g o f t h e s e
s y s t e m s d e p e n d s o n o b s e r v a t i o n
o f t h e m a n u f a c t u r e r ' s r e c o m m e n -
d a t i o n s r e g a r d i n g t h e w h e e l s ( t y r e s
a n d r i m s ) , t h e b r a k i n g c o m p o -
n e n t s , t h e e l e c t r o n i c c o m p o n e n t s
a n d t h e C I T R O Ë N a s s e m b l y a n d
o p e r a t i o n p r o c e d u r e s .
A f t e r a n i m p a c t , h a v e t h e s e s y s -
t e m s c h e c k e d b y a C I T R O Ë N
dealer.
Page 100 of 205
9
DRIVING
PARKING BRAKE
When parking on a slope, direct
your wheels against the pave-
ment, apply the parking brake
and engage a gear.
Applying
Pull the parking brake lever fully up
to immobilise your vehicle. Releasing
Pull the parking brake lever gently,
press the release button then lower
the lever fully.
When the vehicle is being dri-
ven, if this warning lamp and
the STOP warning lamp come
on, accompanied by an audible
signal and a message on the multi-
function screen, this indicates that the
parking brake is still on or has not been
properly released.
6-SPEED MANUAL GEARBOX
Engaging reverse gear
Raise the ring under the knob and
push the gear lever to the left then
forwards.
As a safety precaution and to fa-
cilitate starting of the engine:
- always select neutral,
- press the clutch pedal. Only engage reverse gear when
the vehicle is stationary with the
engine at idle.
Page 102 of 205
9
DRIVING
AUTOMATIC GEARBOX
F o u r - s p e e d a u t o m a t i c g e a r b o x w h i c h
offers a choice between the comfort of
fully automatic operation, enhanced by
sport and snow programmes, or manual
gear changing.
Therefore, four driving modes are of-
fered:
- automatic operation for electronic
management of the gears by the
g e a r b o x ,
- sport programme for a more dynamic
style of driving,
- snow programme to improve driving
when traction is poor,
- manual operation for sequential
changing of the gears by the driver.
1. Gear lever.
2. Button "S"
(sport) .
3. Button "
"
(snow).
Gear selection gate
P. Park.
- Immobilisation of the vehicle, parking brake on or off.
- Starting the engine.
R. Reverse.
- Reversing manoeuvres, vehicle sta- tionary, engine at idle.
N. Neutral.
- Immobilisation of the vehicle, parking brake on.
- Starting the engine.
D. Automatic operation.
M. +/- Manual operation with sequential
changing of the four gears.
Push forwards to change up through
the gears.
or
Pull backwards to change down
through the gears.
Gear lever
When you move the lever in the gate
to select a position, the corresponding
indicator is displayed on the instrument
panel.
P. Park
R. Reverse
N. Neutral
D. Drive (Automatic driving)
S.
Sport programme
.
Snow programme
1, 2, 3, 4
. Gear engaged during manual
operation
-. Invalid value during manual operation
Displays on the instrument panel
Foot on brake
Press the brake pedal when
this indicator lamp is displayed
on the instrument panel (e.g.:
starting the engine).
Page 103 of 205
9
DRIVING
Moving off
Apply the parking brake.
Select position P or N .
Start the engine.
If this procedure is not followed, an au-
dible signal is heard, accompanied by a
message on the multifunction screen.
With the engine running, press the
brake pedal.
Release the parking brake.
Select position R , D or M ,
Gradually release the brake pedal.
The vehicle moves off immediately. Automatic operation
Select position D for automatic
changing of the four gears.
T h e g e a r b o x t h e n o p e r a t e s i n a u t o -
adaptive mode, without any intervention
on the part of the driver. It continuously
selects the most suitable gear accor-
d i n g t o t h e s t y l e o f d r i v i n g , t h e p r o fi l e o f
the road and the load in the vehicle.
F o r m a x i m u m a c c e l e r a t i o n w i t h o u t
touching the lever, press the accelera-
tor pedal down fully (kick down). The
g e a r b o x c h a n g e s d o w n a u t o m a t i c a l l y
or maintains the gear selected until the
m a x i m u m e n g i n e s p e e d i s r e a c h e d .
O n b r a k i n g , t h e g e a r b o x c h a n g e s d o w n
a u t o m a t i c a l l y t o p r o v i d e e f fi c i e n t e n g i n e
braking.
If you release the accelerator sharply,
t h e g e a r b o x w i l l n o t c h a n g e t o a h i g h e r
gear for safety reasons. Sport and snow programmes
These two special programmes supple-
ment the automatic operation in very
s p e c i fi c c o n d i t i o n s o f u s e .
Sport programme "S"
Press button "S" , after starting the
engine.
T h e g e a r b o x a u t o m a t i c a l l y f a v o u r s a
dynamic style of driving.
Snow programme " "
Press button " ", after starting the
engine.
T h e g e a r b o x a d a p t s t o d r i v i n g o n s l i p -
pery roads.
This programme improves starting and
drive when traction is poor.
Return to automatic operation
At any time, press the button selected
again to quit the programme engaged
and return to auto-adaptive mode.
If position
N is engaged inadver-
tently while driving, allow the en-
gine to return to idle then engage
position D to accelerate.
Never select position N while the
vehicle is moving.
Never select positions P or R
unless the vehicle is completely
stationary.
When the engine is running at
idle, with the brakes released,
if position
R , D or M is selected,
the vehicle moves even without
the accelerator being pressed.
When the engine is running,
never leave children in the
vehicle without supervision.
When carrying out maintenance
with the engine running, apply
the parking brake and select
position P .
S appears on the instrument
panel.
appears on the instrument
panel.
Page 104 of 205
9
DRIVING
Manual operation
Select position M for sequential
changing of the four gears.
Push the lever towards the + sign to
change up a gear.
Pull the lever towards the - sign to
change down a gear.
It is only possible to change from one
gear to another if the vehicle speed
and engine speed permit; otherwise,
t h e g e a r b o x w i l l o p e r a t e t e m p o r a r i l y i n
automatic mode.
D disappears and the gears
engaged appear in succes-
sion on the instrument panel.
In the event of the engine la-
bouring or over-revving, the
g e a r s e l e c t e d fl a s h e s f o r a f e w s e c o n d s ,
then the actual gear engaged is dis-
played.
It is possible to change from position D
(automatic) to position M (manual) at
any time.
When the vehicle is stationary or mo-
v i n g v e r y s l o w l y , t h e g e a r b o x s e l e c t s
gear M1 automatically.
The sport and snow programmes do not
operate in manual mode. Invalid value during manual
operation
This symbol is displayed if a gear
is not engaged correctly (selec-
tor between two positions).
Stopping the vehicle
Before switching off the engine, you
can engage position P or N to place the
g e a r b o x i n n e u t r a l .
In both cases, apply the parking brake
to immobilise the vehicle.
If the lever is not in position P ,
when the driver's door is opened
o r a p p r o x i m a t e l y 4 5 s e c o n d s
after the ignition is switched off,
a message appears in the multi-
function screen.
Return the lever to position P ;
the message disappears. There is a risk of damage to the
g e a r b o x :
- if you press the accelera-
tor and brake pedals at the
same time,
- if you force the movement of the gear lever from the
P position to another position
w h e n t h e b a t t e r y i s fl a t .
To reduce fuel consumption
when at a prolonged standstill
w i t h t h e e n g i n e r u n n i n g ( t r a f fi c
jam...), put the gear lever in the
N position and apply the parking
brake.
Operating fault
When the ignition is on,
the lighting of this war-
ning lamp, accompanied
by an audible signal and
a message on the multifunction screen,
i n d i c a t e s a g e a r b o x m a l f u n c t i o n .
I n t h i s c a s e , t h e g e a r b o x s w i t c h e s t o
back-up mode and is locked in 3rd gear.
You may feel a substantial knock when
changing from P to R and from N to R .
This will not cause any damage to the
g e a r b o x .
D o n o t e x c e e d 6 0 m p h ( 1 0 0 k m / h ) , l o c a l
speed restrictions permitting.
Contact a CITROËN dealer as soon as
possible.