Page 120 of 217
VIII
125
DIESEL ENGINE
A c c e s s f o r c h e c k i n g t h e l e v e l s o f t h e v a r i o u s fl u i d s a n d t h e r e p l a c e m e n t o f c e r t a i n c o m p o n e n t s .
1. Coolant reservoir.
2. P o w e r s t e e r i n g fl u i d r e s e r v o i r .
3. Screenwash and headlamp wash reservoir.
4. B r a k e fl u i d r e s e r v o i r .
5. Fusebox.
6. Battery.
7. Engine oil dipstick.
8. E n g i n e o i l fi l l e r c a p .
9. A i r fi l t e r .
Page 121 of 217
VIII
C H E C K S
126
CHECKING LEVELS Brake fluid level To avoid any risk of scalding, unscrew
the cap by two turns to allow the pres-
sure to drop. When the pressure has
dropped, remove the cap and top up
the level.
Oil level
The reading will only be correct
if the vehicle is on level ground
and the engine has been off for
more than 15 minutes.
The check is carried out either when
the ignition is switched on using the oil
level indicator on the instrument panel,
or using the dipstick. T h e b r a k e fl u i d l e v e l s h o u l d b e
between the "MAX" and "MIN"
marks.
If it is not, check the brake pad
wear.
C h a n g i n g t h e b r a k e fl u i d
Refer to the servicing booklet for details
of the interval for this operation.
Coolant level
The coolant level must be
measured when the engine is
cold and should be between
the "LOW" and "FULL" marks.
When the engine is warm, the tem-
perature of the coolant is regulated
by the fan. This can operate with the
ignition off.
O n v e h i c l e s w h i c h a r e fi t t e d w i t h a
p a r t i c l e e m i s s i o n fi l t e r , t h e f a n m a y
operate after the vehicle has been
s w i t c h e d o f f , e v e n i f t h e e n g i n e i s
cold.
In addition, as the cooling system is
pressurised, wait at least one hour after
switching off the engine before carrying
out any work.
Screenwash and headlamp wash * fluid
C h e c k t h e fl u i d l e v e l r e g u l a r l y ,
using the gauge.
* According to country.
Changing the engine oil
Refer to the servicing booklet for details
of the interval for this operation.
In order to maintain the reliability of the
engine and emission control system,
the use of additives in the engine oil is
prohibited.
O i l s p e c i fi c a t i o n
The oil must correspond to your en-
gine and conform to the manufacturer's
recommendations. F l u i d s p e c i fi c a t i o n
T h e b r a k e fl u i d m u s t c o n f o r m t o t h e
manufacturer's recommendations and
f u l fi l t h e D O T 4 s t a n d a r d s .
C h a n g i n g t h e c o o l a n t fl u i d
Refer to the servicing booklet for details
of the interval for this operation.
F l u i d s p e c i fi c a t i o n
The coolant must conform to the manu-
facturer's recommendations.
F l u i d s p e c i fi c a t i o n
T h i s fl u i d m u s t c o n f o r m t o t h e m a n u f a c -
turer's recommendations for optimum
cleaning.
Power steering fluid level
C h e c k t h e fl u i d l e v e l w i t h t h e e n g i n e a t
idle.
C h e c k t h a t t h e p o w e r s t e e r i n g fl u i d
level is always between the "MAX" and
"MIN" marks and top up if necessary.
F l u i d s p e c i fi c a t i o n
T h i s fl u i d m u s t c o n f o r m t o t h e m a n u f a c -
turer's recommendations.
Check all of these levels regularly and
top them up if necessary, unless other-
wise indicated.
I f a l e v e l d r o p s s i g n i fi c a n t l y , h a v e t h e
corresponding system checked by a
CITROËN dealer.
When working under the bonnet, take
care as certain areas of the engine may
be extremely hot (risk of burns).
Page 130 of 217
IX
!
!
P R A C T I C A L I N F O R M A T I O N
134
CHANGING A BULB
H a n d l e t h e b u l b s u s i n g a d r y
cloth.
Do not clean the headlamps using
a dry or abrasive cloth, or using
detergent or solvent products, u s e
a s p o n g e a n d s o a p y w a t e r . I n s o m e w e a t h e r c o n d i t i o n s ( e . g . l o w
t e m p e r a t u r e o r h u m i d i t y ) , t h e p r e s e n c e
o f m i s t i n g o n t h e i n t e r n a l s u r f a c e o f t h e
g l a s s o f t h e h e a d l a m p s a n d r e a r l a m p s
i s n o r m a l ; i t d i s a p p e a r s a f t e r t h e l a m p s
h a v e b e e n o n f o r a f e w m i n u t e s .
Front lamps
1. Direction indicators
(PY21W - 21 W).
2. Dipped
beam
headlamps
(H11 - 55 W)
or xenon bulb (D2S - 35 W).
3. Sidelamps
(W5W - 5 W).
4. Main beam headlamps
(H7 - 55 W).
5. Front
foglamps
(H11 - 55 W). WARNING: RISK OF
ELECTROCUTION
X e n o n b u l b s m u s t b e r e p l a c e d b y a
C I T R O Ë N d e a l e r .
Page 132 of 217
IX
136
Changing sidelamp bulbs (3)
Unscrew the cover H .
Disconnect the connector.
T u r n t h e b u l b h o l d e r I a q u a r t e r o f a
t u r n a n d r e m o v e i t .
P u l l t h e b u l b a n d c h a n g e i t .
T o r e fi t , c a r r y o u t t h e s e o p e r a t i o n s i n
reverse order.
Unscrew the cover F .
Disconnect the connector.
T u r n t h e b u l b G t o t h e l e f t a n d r e -
move it.
T o r e fi t , c a r r y o u t t h e s e o p e r a t i o n s i n
reverse order.
Changing dipped beam headlamp
bulbs (2)
Changing main beam headlamp
bulbs (4)
Unscrew the cover J .
Disconnect the connector.
M o v e a s i d e t h e s p r i n g K to release
t h e b u l b a n d r e m o v e i t .
T o r e fi t , c a r r y o u t t h e s e o p e r a t i o n s i n
reverse order.
