2010 CHRYSLER SEBRING CONVERTIBLE lock

CavityCartridge
Fuse Mini
Fuse Description
13 —20 Amp
Yellow —
14 —10 Amp
Red Ignition Off Draw
(IOD) – Cabin
Compartment
Node (CCN)/
Interior Lighting
15 40 Amp
Green —Battery Feed – Ra-
diator Fan Relay
16 —15 Amp
Lt. Blue IGN Run/ACC –
Cigar Lighter/
PWR Sunroof
ModCavity
Cartridge
Fuse Mini
Fuse Description
17 — 10 Amp
Red Ignition Off Draw
(IOD) – Wireless
Control Module
(WCM)/Clock/
Steering Control
Module (SCM)
18 40 Amp
Green —Battery Feed –
Auto Shutdown
(ASD) Relay
19 —20 Amp
Yellow Ignition Off Draw
(IOD) – Power
AmpFeed2–If
Equipped
20 —15 Amp
Lt. Blue Ignition Off Draw
(IOD) – Radio
21 —10 Amp
Red —
390 MAINTAINING YOUR VEHICLE

CavityCartridge
Fuse Mini
Fuse Description
31 —10 Amp
Red —
32 30 Amp
Pink —Auto Shutdown
(ASD) Relay Feed
1
33 —10 Amp
Red Battery Feed –
Switch Bank/
Diagnostic Link
Connector/
Powertrain Con-
trol Module
(PCM)Cavity
Cartridge
Fuse Mini
Fuse Description
34 30 Amp
Pink —Battery Feed –
Anti-Lock Brakes
(ABS) Module – If
Equipped/
Electronic Stability
Control (ESC)
Module – If
Equipped
35 40 Amp
Green —Battery Feed –
Anti-Lock Brakes
(ABS) Module – If
Equipped/
Electronic Stability
Control (ESC)
Module – If
Equipped
392 MAINTAINING YOUR VEHICLE

4. Pull the bulb out of the socket and replace the bulb.
5. If the bulb comes in contact with any oily surface,
clean the bulb with rubbing alcohol.
6. Reinsert the bulb and socket assembly and rotate
clockwise one-quarter turn to secure.Front Turn Signal/Parking Lamp
1. Raise and prop open the hood.
2. Rotate the bulb’s electrical connector one-quarter turn
counterclockwise and remove it from the headlamp
housing.
396 MAINTAINING YOUR VEHICLE

3. Remove the bulb from the connector socket and install
the replacement bulb.
4. Install the bulb and connector assembly into the
headlamp housing and rotate the connector one-quarter
turn clockwise to lock it in place.
Front Fog Lamp
NOTE:Access to the lamps through the lower fascia
cutout is limited. We recommend you access the lamps by
turning the steering wheel to allow access and remove
the inner fender shield.
1. Rotate the bulb’s electrical connector one-quarter turn
counterclockwise and remove it from the fog lamp hous-
ing. 2. Remove the bulb from the connector socket and install
the replacement bulb.
7
MAINTAINING YOUR VEHICLE 397

CAUTION!
Do not touch the new bulb with your fingers. Oil
contamination will severely shorten bulb life. If the
bulb comes in contact with an oily surface, clean the
bulb with rubbing alcohol.
3. Install the bulb and connector assembly into the fog
lamp housing and rotate the connector one-quarter turn
clockwise to lock it in place.
Tail/Stop, Rear Turn Signal and Backup Lamps
The taillamps are a two piece design. The turn signal,
brake and taillamps are located in the rear corner body
panel housing. The backup and taillamps are located in
the trunk lid housing.
398 MAINTAINING YOUR VEHICLE

4. Rotate the applicable bulb’s electrical connector one-
quarter turn counterclockwise and remove it from the
taillamp housing.5. Remove the bulb from the connector socket and install
the replacement bulb.
6. Install the bulb and connector assembly into the
taillamp housing and rotate the connector one-quarter
turn clockwise to lock it in place.
7. Reinstall the taillamp housing.
Changing the Backup Lamp
1. Open the trunk.
2. Rotate the bulb’s electrical connector one-quarter turn
counterclockwise and remove it from the housing.
1 — Tail/Stop Lamp
2 — Turn Signal Lamp
400 MAINTAINING YOUR VEHICLE

3. Remove the bulb from the connector socket and install
the replacement bulb.
4. Install the bulb and connector assembly into the
housing and rotate the connector one-quarter turn clock-
wise to lock it in place.
License Plate Lamp
1. Remove two retaining screws holding the lamp lens in
place.
2. Gently pry the lens loose.
3. Pull bulb from socket, replace and reattach the lamp
lens with the two retaining screws.
1 — Rear Fog Lamp2 — Backup Lamp
7
MAINTAINING YOUR VEHICLE 401

Center High-Mounted Stop Lamp (CHMSL)
1. Open the trunk lid.
2. Rotate the bulb’s electrical connector one-quarter turn
counterclockwise and remove it from the CHMSL hous-
ing.3. Remove the bulb from the connector socket and install
the replacement bulb.
4. Install the bulb and connector assembly into the
CHMSL housing and rotate the connector one-quarter
turn clockwise to lock it in place.
402 MAINTAINING YOUR VEHICLE