2010 CHRYSLER PT CRUISER bulb

▫Brake System ...................... 298
▫ Automatic Transmission .............. 299
▫ Appearance Care And Protection From
Corrosion .......................... 302
 Fuses ............................. 308
▫ Integrated Power Module (IPM) ......... 308
 Vehicle Storage ...................... 311
 Replacement Bulbs ................... 311
 Bulb Replacement .................... 312
▫ Headlamps ....................... 312
▫ Front Parking, Turn Signal, And Side Marker
Lamps ............................ 313 ▫
Front Fog Lamps – If Equipped ......... 314
▫ Rear Tail, Stop And Turn Signal Lamps . . . 314
▫ Backup Lamps ..................... 315
▫ Center High-Mounted Stop Lamp
(CHMSL) .......................... 315
 Fluid Capacities ..................... 316
 Fluids, Lubricants And Genuine Parts ...... 317
▫ Engine ........................... 317
▫ Chassis .......................... 318
276 MAINTAINING YOUR VEHICLE

Indicator Light (MIL)” is functioning and is not on when
the engine is running, and that the OBD II system is
ready for testing.
Normally, the OBD II system will be ready. The OBD II
system maynotbe ready if your vehicle was recently
serviced, recently had a dead battery or a battery replace-
ment. If the OBD II system should be determined not
ready for the I/M test, your vehicle may fail the test.
Your vehicle has a simple ignition key-actuated test,
which you can use prior to going to the test station. To
check if your vehicle’s OBD II system is ready, you must
do the following:
1. Turn the ignition switch to the ON position, but do not
crank or start the engine.
2. If you crank or start the engine, you will have to start
this test over. 3. As soon as you turn the ignition switch to the ON
position, you will see the MIL symbol come on as part of
a normal bulb check.
4. Approximately 15 seconds later, one of two things will
happen:
a. The MIL will flash for about 10 seconds and then
return to being fully illuminated until you turn OFF
the ignition or start the engine. This means that your
vehicle’s OBD II system is not readyand you should
not proceed to the I/M station.
b. The MIL will not flash at all and will remain fully
illuminated until you turn OFF the ignition or start the
engine. This means that your vehicle’s OBD II system
is ready and you can proceed to the I/M station.
If your OBD II system is not ready,you should see your
authorized dealer or repair facility. If your vehicle was
recently serviced or had a battery failure or replacement,
7
MAINTAINING YOUR VEHICLE 279

CAUTION!
•When installing the Integrated Power Module
cover, it is important to ensure the cover is prop-
erly positioned and fully latched. Failure to do so
may allow water to get into the Integrated Power
Module, and possibly result in an electrical system
failure.
•When replacing a blown fuse, it is important to
use only a fuse having the correct amperage rating.
The use of a fuse with a rating other than indicated
may result in a dangerous electrical system over-
load. If a properly rated fuse continues to blow, it
indicates a problem in the circuit that must be
corrected.
VEHICLE STORAGE
If you will not be using your vehicle for more than
21 days, you may want to take steps to preserve your
battery.
•Disengage the mini-fuse in the Power Distribution
Center labeled IOD (Ignition Off-Draw).
•Disconnect the negative cable from the battery.
REPLACEMENT BULBS
LIGHT BULBS – InteriorBulb No.
Center Console Floor Lamp ................. T37
Climate Controls ...................... 6233137
Console Gear Selector ................... PC194
Dome Lamp (Sedan) ..................... T579
Instrument Cluster Illumination ............... 74
Overhead Reading Lamp (Overhead Console) . . . T1037
Overhead Reading Lamp (Rearview Mirror) .....T192
Rear Cargo ............................ T906
Visor Vanity ......................... 6501966
7
MAINTAINING YOUR VEHICLE 311

All the interior bulbs are brass or glass wedge base.
Aluminum base bulbs are not approved and should not
be used for replacement.
LIGHTS BULBS – Exterior Bulb No.
Low Beam Headlamp................... 9006XS
High Beam Headlamp .................. 9005XS
Front Park/Turn Signal/Side Marker
Lamp ............................ 4157NAKX
Front Fog Lamp ......................... 9145
Center High-Mounted Stop Lamp (CHMSL)
(Sedan) .......................... 921–W16W
Rear Tail/Stop .......................... 3157
Rear Turn Signal ....................... 3757A
Backup Lamp .................... 3157-P27/7W
License Lamp ........................... 168BULB REPLACEMENT
Headlamps
CAUTION!
Do not touch the new headlamp bulb with your
fingers. Oil contamination will severely shorten bulb
life.
1. Remove the headlamp access cover splash shield,
located in the front wheel well opening.
2. Disconnect the electrical connector(s).
312 MAINTAINING YOUR VEHICLE

3. Rotate the socket to the left one-quarter turn, and
replace the bulb.
Front Parking, Turn Signal, and Side Marker
Lamps
1. Remove the headlamp access cover splash shield,
located in the front wheel well opening.2. Disconnect the electrical connector.
3. Rotate the socket to the left one-quarter turn, and
replace the bulb.
7
MAINTAINING YOUR VEHICLE 313

Front Fog Lamps – If Equipped
1. Remove the fasteners attaching the lower splash
shield to gain access to the fog lamp.
2. Twist and remove the bulb from the fog lamp housing.
3. Disconnect the electrical connector and replace bulb.
Rear Tail, Stop and Turn Signal Lamps
1. Remove the screw attaching the tail lamp housing and
remove the housing from the vehicle.
2. Twist the bulb socket one–quarter turn to remove it
from the housing.3. Pull the bulb out of the socket and replace.
314 MAINTAINING YOUR VEHICLE

Backup Lamps
1. To remove the backup lamp, you must take a fiber
stick and slide it along the inboard side of the lamp and
compress a spring clip to allow it to partiallypopout to
the secondary catch. 2. Fully compress the clip to get the lamp to come out
completely.
3. Remove the socket from the housing.
4. Pull the bulb out of the socket and replace.
Center High-Mounted Stop Lamp (CHMSL)
1. Open the liftgate and remove the liftgate CHMSL
cover.
2. Remove CHMSL lens from the housing by unlatching
the two side latches.
3. Pull the bulb out of the socket and replace.
7
MAINTAINING YOUR VEHICLE 315

Special Additives...................... 301
Autostick ............................. 200
Back-Up Lights ......................... 315
Battery ............................... 286
Keyless Transmitter Replacement (RKE) ....... 25
Belts, Seat .............................. 75
Body Mechanism Lubrication ............... 288
B-Pillar Location ........................ 219
Brake, Parking .......................... 207
Brake System ........................ 209,298
Anti-Lock (ABS) ....................... 210
Fluid Check .......................... 298
Master Cylinder ....................... 298
Parking ............................. 207
Warning Light ........................ 150
Brakes ............................... 209
Brake/Transmission Interlock ............... 195
Break-In Recommendations, New Vehicle ........ 72Bulb Replacement
..................... 31 1,312
Bulbs, Light .......................... 77,311
Calibration, Compass ...............157,162,167
Capacities, Antifreeze (Engine Coolant) ........ 316
Capacities, Fluid ........................ 316
Caps, Filler Fuel ............................... 242
Oil (Engine) ....................... 277,284
Power Steering ........................ 206
Radiator (Coolant Pressure) ............... 295
Car Washes ............................ 303
Carbon Monoxide Warning ...............74,241
CD (Compact Disc) Player ................. 168
Cellular Phone .......................... 180
Center High Mounted Stop Light ............ 315
Chains, Tire ............................ 231
Changing A Flat Tire ..................... 262
Chart, Tire Sizing ........................ 215
10
INDEX 351