2010 CHRYSLER 300 key battery

High/Low Beam Switch
Push the multifunction lever away from you to switch
the headlights to high beam. Pull the multifunction lever
toward you to switch the headlights back to low beam.
Flash-to-Pass
You can signal another vehicle with your headlights by
lightly pulling the multifunction lever toward you. This
will turn on the high beams headlights until the lever is
released.
Overhead Console Map/Reading Lights
These lights are mounted between the sun visors on the
overhead console. Each light is turned on by pressing the
lens. Press the lens a second time to turn off the light.
These lights also turn on when a door is opened, or when
the UNLOCK button on the Remote Keyless Entry (RKE)
transmitter is pressed or when the dimmer control is
turned fully upward, past the second detent.
Interior Lights
The interior lights come on when a door is opened.
To protect the battery, the interior lights will turn off
automatically 10 minutes after the ignition is placed in
the OFF position. This will occur if the interior lights
were switched on manually or are on because a door is
Overhead Console
3
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 149

•Channel # Trained
•Clearing Channels
•Channels Cleared
•Did Not Train
•Left Front Low Pressure (with a single chime). Refer to
information on “Tire Pressure” and “Tire Pressure
Monitor” under “Starting And Operating.”
•Left Rear Low Pressure (with a single chime). Refer to
information on “Tire Pressure” and “Tire Pressure
Monitor” under “Starting And Operating.”
•Right Front Low Pressure (with a single chime). Refer
to information on “Tire Pressure” and “Tire Pressure
Monitor” under “Starting And Operating.”
•Right Rear Low Pressure (with a single chime). Refer
to information on “Tire Pressure” and “Tire Pressure
Monitor” under “Starting And Operating.”
•Check TPM System (with a single chime). Refer to
information on “Tire Pressure Monitor” under “Start-
ing And Operating.”
•Check Gascap (refer to “Adding Fuel” in “Starting
And Operating”)
•Service Park Assist System (with a single chime)
•Turn To Run (refer to “Remote Starting System” in
“Things To Know Before Starting Your Vehicle”)
•Key Fob Battery Low
•Service Keyless System
•Wrong Key
•Push Button or Insert Key/Turn To Run (refer to
“Remote Starting System” in “Things To Know Before
Starting Your Vehicle”)
•Oil Change Required (with a single chime)
4
UNDERSTANDING YOUR INSTRUMENT PANEL 235

WARNING! (Continued)
•Do not attempt to push or tow your vehicle to get
it started. Vehicles equipped with an automatic
transmission cannot be started this way. Unburned
fuel could enter the catalytic converter and once
the engine has started, ignite and damage the
converter and vehicle. If the vehicle has a dis-
charged battery, booster cables may be used to
obtain a start from a booster battery or the battery
in another vehicle. This type of start can be dan-
gerous if done improperly. Refer to “Jump Start-
ing” in “What To Do In Emergencies” for further
information.
Clearing a Flooded Engine (Using ENGINE
START/STOP Button)
If the engine fails to start after you have followed the
“Normal Starting” or “Extreme Cold Weatherproce-
dures, it may be flooded. To clear any excess fuel, press and hold the brake pedal, push the accelerator pedal all
the way to the floor and hold it, then press and release the
ENGINE START/STOP button once. The starter motor
will engage automatically, run for 10 seconds, and then
disengage. Once this occurs, release the accelerator pedal
and the brake pedal, wait 10 to 15 seconds, then repeat
the “Normal Starting” procedure.
Clearing A Flooded Engine (Using Fob With
Integrated Key)
If the engine fails to start after you have followed the
“Normal Starting” or “Extreme Cold Weather” proce-
dures, it may be flooded. To clear any excess fuel, push
the accelerator pedal all the way to the floor and hold it.
Then, turn the ignition switch to the START position and
release it as soon as the starter engages. The starter motor
will disengage automatically in 10 seconds. Once this
occurs, release the accelerator pedal, turn the ignition
switch to the LOCK position, wait 10 to 15 seconds, then
repeat the “Normal Starting” procedure.5
STARTING AND OPERATING 313

Brake/Transmission Interlock Manual Override
There is an override for the BTSI that allows you to move
the shift lever out of the PARK position if an electrical
system malfunction occurs (i.e., dead battery). To access
the override, remove the rubber tray from the storage bin
located to the right of the shift lever. The override access
port is at the top of the bin to the right of the shift lever
gate.
1. Turn the ignition switch to the ACC or ON position
(RUN position with Keyless Go™) without starting the
engine.
2. Firmly set the parking brake.
3. Press and maintain firm pressure on the brake pedal.
4. Using the screwdriver, press and hold the override tab
through the access port on the center console.5. Move the shift lever into the NEUTRAL position.
6. The vehicle may then be started in NEUTRAL.
7. Reinstall the override cover.
Interlock Manual Override
318 STARTING AND OPERATING

TRIP ODOMETER button to turn off the message. If the
problem continues, the message will appear the next time
the vehicle is started.
A loose, improperly installed, or damaged fuel filler cap
may also turn on the MIL.
EMISSIONS INSPECTION AND MAINTENANCE
PROGRAMS
In some localities, it may be a legal requirement to pass
an inspection of your vehicle’s emissions control system.
Failure to pass could prevent vehicle registration.For states that require an Inspection and Mainte-
nance (I/M), this check verifies the “Malfunction
Indicator Light (MIL)” is functioning and is not
on when the engine is running, and that the OBD II
system is ready for testing.
Normally, the OBD II system will be ready. The OBD II
system may notbe ready if your vehicle was recently serviced, recently had a dead battery or a battery replace-
ment. If the OBD II system should be determined not
ready for the I/M test, your vehicle may fail the test.
Your vehicle has a simple ignition key-actuated test,
which you can use prior to going to the test station. To
check if your vehicle’s OBD II system is ready, you must
do the following:
1. Turn the ignition switch to the ON position, but do not
crank or start the engine.
2. If you crank or start the engine, you will have to start
this test over.
3. As soon as you turn the ignition switch to the ON
position, you will see the MIL symbol come on as part of
a normal bulb check.
4. Approximately 15 seconds later, one of two things will
happen:
7
MAINTAINING YOUR VEHICLE 427

Auto Unlock, Doors....................... 34
Auto Up Power Windows .................. 41
Automatic Dimming Mirror ................. 92
Automatic Door Locks ................... 32,34
Automatic Headlights .................... 145
Automatic Oil Change Indicator ..........219,236
Automatic Temperature Control (ATC) ......... 296
Automatic Transaxle Special Additives ...................... 453
Automatic Transmission ...........319,324,452,453
Adding Fluid ...................... 453,483
Autostick ............................ 328
Fluid and Filter Changes ................. 453
Fluid Change ......................... 453
Fluid Level Check ..................... 452
Fluid Type ........................... 483
Gear Ranges ....................... 319,324
Overdrive ........................... 321
Shifting .......................... 319,324Special Additives
...................... 453
Torque Converter ...................... 322
Automatic Transmission Limp Home Mode . . 323,327
Autostick ............................. 328
Axle Fluid ............................. 483
Axle Lubrication (Axle Fluid) ............... 483
Battery ............................... 434
Keyless Transmitter Replacement (RKE) ....... 26
Location ............................ 434
Belts, Seat ............................ 46,82
Body Mechanism Lubrication ............... 439
B-Pillar Location ........................ 351
Brake Assist System ...................... 341
Brake Control System, Electronic ............. 340
Brake Fluid ............................ 483
Brake, Parking .......................... 335
Brake System ........................... 449
Anti-Lock (ABS) ....................... 338
10
INDEX 517

Towing Vehicle Behind a Motor Home......... 396
Traction Control ......................... 340
Trailer Towing .......................... 384
Cooling System Tips .................... 396
Hitches ............................. 386
Minimum Requirements ................. 389
Tips ................................ 395
Trailer and Tongue Weight ............... 388
Wiring .............................. 393
Trailer Towing Guide ..................... 388
Trailer Weight .......................... 388
Transfer Case ........................... 454
Fluid ............................ 454,483
Maintenance ......................... 454
Transmission ........................... 452
Automatic ................... 314,319,324,452
Fluid ............................... 483
Range Indicator .................... 319,324
Shifting ............................. 314 Transmitter Battery Service
(Remote Keyless Entry)
.................... 26
Transmitter, Garage Door Opener (HomeLink) . . 190
Transmitter Programming
(Remote Keyless Entry) .................... 20
Transmitter, Remote Keyless Entry (RKE) ........ 20
Transporting Pets ........................ 80
Tread Wear Indicators .................... 360
Trip Odometer ....................... 216,224
Trunk Lid (Deck Lid) .................... 43,44
Trunk Release, Emergency .................. 44
Trunk Release Remote Control ............... 43
Turn Signals ......................... 148,216
UCI Connector ......................... 277
Uconnect™ (Hands-Free Phone) .............. 96
Uniform Tire Quality Grades ................ 513
Universal Consumer Interface (UCI) Connector . . . 277
Universal Transmitter ..................... 190
10
INDEX 535