2010 AUDI A5 COUPE warning light
[x] Cancel search: warning lightPage 252 of 360
___ T_ r _a_ il_e _r_ t_ o_ vv_ in__... g,_ __________________________________________________ _
Observe speed limits. In some areas, speeds for vehicles towing
trailers are lower than for regular vehicles.
Always apply brakes early. When driving downhill, shift into a lower gear to use the engine braking effect to slow the vehicle. Use of the
brakes a lone can cause them to overheat and fail.
Coolant temperature
The coolant temperature gauge=> page 8 must be observed care
ful ly . If the needle moves close to the upper end of the scale, reduce
speed immediately and/or turn off the air conditioner .
If the coolant temperature warning light in the instrument cluster
starts flashing
-F- , pul l off the road, stop and let the engine idle for
about two minutes to prevent heat build-up .
& WARNING
Anyone not properly restrained in a moving vehicle is at a much
greater risk in an accident. Never let anyone ride in your car who
is not properly wearing the restraints provided by Audi . •
Trailer towing tips
Important to know
----------------
Your vehicle handles differently when towing a trailer because of
the additional weight and different weight distribution. Safety,
performance and economy will great ly depend on how careful ly you
load your trailer and operate your rig.
Before you actual ly tow your trailer, pract ice turning, stopping and
backing up in an area away from traffic. Keep practicing unti l you
have become completely familiar with the way your vehicle -trailer
combination behaves and responds . Backing
up is difficult and requires practice . Backing up with a
t rai ler genera lly requires steering action opposite to that when
backing up your vehicle without a trailer .
Maintain a greater distance between your vehicle and the one in
front of you. You will need more room to stop . To compensate for
the trai ler, you wi ll need a larger than norma l turning radius.
When passing, remember that you cannot accelerate as fast as you
normally would because of the added load. Make sure you have
enough room to pass. After passing, al low plenty of room for your
trai ler before changing lanes again .
Avoid jerky starts, sharp turns or rapid lane changes.
[ i ] Tips
• Do not tow a trailer during the break -in period of your vehicle.
• If you tow a trailer, your Audi may require more frequent mainte
nance due to the extra load=>
page 339. •
Parking on a s•ope
Do not pork on a slope with a trailer. If it cannot be
avoided, do so only ofter doing the following:
When parking:
Apply the foot brake.
- Have someone p lace chocks under both the vehicle and
the trailer wheels.
With chocks in place, slow ly release the brakes until the
wheel chocks absorb the load.
- Turn the wheels towards the curb.
- Apply the parking brake.
Page 254 of 360
-Cleaning and prot ection
P'tr:1-~--------------
Cleaning and protection
General information
Regular ca re p rese rves vehicle value .
Any automobile is exposed to industrial fumes, corrosive road salt ,
muddy dog feet, e tc. A wel l cared fo r Audi can look l ike new many
years after purchase . Regu lar and correct care will contribute to
maintaining the beauty and va lue of your Audi .
Fu rthe rmo re , g ood care ma y be a conditi on for sub sta ntiating a
warr anty cla im should corro sion damage or paint defect s occur .
Your authorized Audi dealer has a var iety of dedi cat ed vehicle -care
product s
and can advise which ones to use for cleaning the exterior
and interio r of your vehicle.
Whether you use products recommended by Audi or other commer
cially availab le cleaning agen ts, please make su re you apply them
correctly .
& WARNING
• Cleaning agents m ay be poi sonou s. Keep them out of the re ach
of childr en.
• Heed all cau tion label s.
• Alway s read direction s on the container before u sing any
produ ct. Follo w the dire ction s carefull y.
• Most chemi cal cle aner s are concentr ated and h ave to be
d iluted .
• Use spot remo ving fl uid s onl y
in well ventila ted are as.
• Do not use gasoline , kero sene , diesel fuel , nail poli sh remover
or other vol atil e fluid s. They may be to xic , fl ammab le or h azardou s
in other wa ys. Do not wa sh , wax or dry the vehicle w ith the igni
tion on or the engine ru nning .
& WARNING (continued )
• Do not clean the unders ide s of cha ssi s, fenders , wheel cover s,
et c. without pr ote cting y our hands and arm s. You may cut your self
on sh arp-edged metal part s.
• Moisture and i ce on brakes may impair br aking eff icien cy
~ page 237, "General information ". Test the brake s carefully each
time you wash the vehicle .
'£> For the sake of the environment
Select only environmenta lly friend ly c leaning products. Leftover
clean ing products should not disposed of in the household waste .•
Care of exterior
Washing
F requent washing protects the vehicle.
The best protection against environmental influences is frequent
washing a nd waxing. How often this is required depends on :
• How much the vehicle is used
• Where the vehic le is pa rked (garage, in the open under trees,
etc.I
• The seasonal and weather cond itions
• Environmental influences
The longer bird dropp ings, insects, tree resin, road and industrial
grime, tar, soot, road salt and other materials remain on the vehicle
b ody, the more lasting their destructive effects will be. High temper
atures caused by exposure to intense sunlight intensify the corro -
sive effect, particularly when humidity is high as wel l. .,
Page 256 of 360
___ C_ le_ a _ n_i_n ~g _ a_ n_ d __ p_r _o _t _e _c_ t_ i_o _n ___________________________________________ _
0 Note
• Never try to remove d irt, mud or dust if the surface of the vehicle
is dry . Never use a dry cloth or sponge, since this cou ld scratch your
vehic le's paint or w indows.
• Never wash your car in bright sunlight. Drops of water act as
magnify ing lenses and may damage your paint.
• When you wash your car in the winter : if you rinse your vehicle
with a hose, be careful not to aim the stream of water directly at
locks, or at door or hatch openings -they can freeze shut.
• Never use sponges designed to remove insects, or any kitchen
scouring sponges or similar products. They can damage your paint
finish .
• Never use a dry cloth or sponge to c lean the head ligh ts. Only use
wet cloths or sponges to prevent scratches . It is best to use soapy
water.
For the sake of the environment
In the interest of the environment, the vehicle should on ly be
washed in specia l wash bays. •
Washing your vehicle with a power washer
Cleaning the exterior of your car with a high -p ressure
power washer is safe as l ong as y ou observe a few simple
rules .
-Before using the power washer, make s ure you have read
and understood the WAR NINGS=::;,
& in "General infor
mati on" o n
page 252.
-Always follow the operating instructions for the power
washer. - Make sure that the jet o
n the spray hose pro duces a "fan
sha ped sp ray".
D o
not hold the spray nozzle too close to soft materials.
When cleaning the vehicle with a power washer always follow the
operating instructions. This applies particula rly to the
operating
pre ssure
and the spraying di stance . Maintain a sufficient distance
to soft materia ls such as rubber hoses and sound/vibration dead
ening materia ls (part icularly on the underside of the engine hood).
Do not use a jet which sprays water in a
direct stream or one that
has a
rotating jet.
Water temperature should not exceed 140 °F (60 °Cl.
& WARNING
Never wash tire s with a jet that sp ra ys water in a dir e ct stream .
Thi s could cau se invisible damage to the tire s and we ake n them ,
eve n if th e spra y is from a re lativel y lo ng dis tanc e an d f or a sh o rt
time . Damaged and weakened tire s can f ail and cau se ac cident s
a nd per sona l injur y.
0 Note
To avoid damaging your vehicle, always make sure that there is
suffic ient distance between the spray head and soft materia ls like
rubber hoses, plastic parts and sound -deadening materials . Never
aim the spray head at the same p oint for a long time . This also
applies to cleaning headlights and painted bumpers . Remember :
the c loser the nozzle is to the surface of the material, the greater the
stress on the mater ial. •
Page 257 of 360
Cleaning and prote ction -
----------------
•
Waxing
Wax prote cts the vehicle's paint.
- Use a manually applied car wax occasion ally to protect
t h e paint.
A good wax coating protects the vehicle paint to a large extent
against th e environm ental factors listed under~
page 252,
"Washing" and even against slight scratches .
You can use a liquid car wax to protect your paint as soon as one
wee k after you r vehic le has been delivered .
Even if you regularly use a
waxing process in automatic car washes,
we recommend that you manua lly app ly a coat of wax to give the
paint e xtra protection, par ticu lar ly if water no longer beads on the
clean paint.
Protec t plastic body parts with car wax in the same way as the
vehic le body.
During warm weather dead insects tend to col lect on the front
bumpe r and on the forward area of the hood. They are much easie r
to remove from paint that is waxed
often.
& WARNING
Always read and heed all WARNINGS and other information
~ page 25 2.
0 Note
Do not use ca r wax on
• matte or anodized meta l trim
• rubber or rubber -like trim. •
Polishing
Polishi ng resto res the gloss to the p aint.
Po lish your vehic le on ly if the paint has lost its shine and the g loss
cann ot be brought back wi th wax .
I f the polish used does not contain preservative compounds , the
paint must be waxed afterwards~
page 255, "Waxing".
& WARNING
Always read and heed all WARNINGS and other information
~ page 252 .
0 Note
Do not treat matte anodized metal trim, plastic or rubber parts with
polish or wax .•
Trim strips
Metal trim needs special c are.
Fo r envi ronmental reasons, Audi fab ricates the bright trim strips
and trim pieces from pure chromium -free aluminum .
Dirt and marks on the trim strips should be removed with a
pH
balanced
c leaning agent (do no t use a chr ome clean er). Authorized
Audi dea lers carry c leaning products which have been tested for use
on your vehicle and are not harm fu l to the enviro nment .
To avoid corrosion on the exterior trim strips , only a pH -ba lanced
solution shou ld be used for the windshield washer .
& WARNING
Always read and heed all WARNINGS and other information
~ page 252 .•
Vehicle care I t •
Page 258 of 360
-~_C_ l_ e _a _n_ in_g=- a _n_d__, p,__ ro_ t_e _c_ t_ i_o _n _____________________________________________ _
Plastic and vinyl
Plastic needs special care.
Use a clean, damp cloth or sponge to remove dust and light surface
dirt. For other soil, use a lukewarm all -purpose cleaning solution or
a mild saddle soap for vinyl trim. Remove water spots and traces of
soap with a clean, damp cloth or sponge . Use a clean, soft cloth to
rub dry .
Grease, tar or oil stains can be removed with a clean cloth or sponge
soaked with all-purpose cleaner or with a solvent designed espe
cially to clean vinyl.
Occasionally apply a colorless vinyl or leather preservative to retain
the material's luster and pliability.
& WARNING
Always read and heed all WARNINGS and other information
~ page252. •
Aluminum trim
Use only neutral-pH products to remove spots and deposits from
aluminum surfaces. Chrome care products and alkaline cleaners
will attack aluminum surfaces and can damage them over time.
& WARNING
Always read and heed all WARNINGS and other information
~ page252 .•
Touch-up paint
Minor paint damages should be touched up immediately.
-Use either a touch -up paint stick or spray paint to cover
minor scratches and nicks.
Your authorized Audi dealer has touch-up paint for minor scratches
and stone chips. Scratches should be touched up soon after they
occur to prevent corrosion.
If a spot starts to rust, however, a simple touch-up job will not be
enough. The affected surface must be sanded smooth and coated
with an anti-rust primer before the painted finish can be restored.
The number for the original vehicle paint can be found on the
vehicle identification label~
page 334.
& WARNING
Always read and heed all WARNINGS and other information
~ page252.•
Windows
Clear vision to all sides.
Clean all windows regularly to remove road film and car
wash wax buildup.
- Remove snow from windows using a brush.
- Use a plastic ice scraper to remove ice from windows and
mirrors.
- Remove other residue on the windows with a spray-on
glass cleaner.
- Wipe the windows dry with a clean piece of cloth or
kitchen paper towel.
Page 260 of 360
___ C_ le_ a _ n_i_n ~g _ a_ n_ d __ p_r _o _t _e _c_ t_ i_o _n ___________________________________________ _
Cast (light) alloy wheels
Cast (light) alloy w heels require special care.
- Wash the wheels with a sponge or hose brush every
o th er week .
- For deep cleaning afte rwards, use only a dedicated
acid
free
cast a lloy wheel c leaner.
- Rub a coat of
liquid wa x onto the rims every t hree month.
Be sure to reac h and treat all parts of the rim.
To preserve the decorative appearance of the cast alloy wheels,
some special care is necessary. In add ition to road dirt and salt,
brake dust is also corrosive . If left on for too long, brake dust can
cause p itting.
Use on ly spec ial
acid -free cleaners formu lated for a lloy rims . Safe
products are available at your authorized Audi dealer. Never leave
t he cleaner on the rims longer than specif ied on the label. If not
rinsed off promptly, the acid contained in some cleaners can attack
t he threads on t he wheel bolts.
Never use abrasive or metal po lishing c leaning agents . If the protec
t ive coating has been chipped, e.g . by kicked up road dirt, touch it
up as soon as possible.
& WARNING
• Moi sture and ice on b rake s ma y affe ct b raking effi cienc y
=> page 23 7, " General information ". Te st the brakes carefully ea ch
t ime you wa sh the vehi cle .
• Always read and heed all WARNINGS and other informat ion
=> page 25 2. •
Body cavity sealing
T he body c avity se aling does n ot need to be c hecked .
All body cavities which could be affected by corrosion have been
th or ough ly pro tected at the factory .
T his sealing does not require any inspection or additional treat
ment . If any wax should seep out of the cavity when the ambient
temperature is high, it can be removed with a p lastic scraper and a
suitable solvent.
& WARNING
Solvent s can be dangerou s.
• Ben zine is flamm able and to xic . If you use benzine for removing
the wax , keep sparks , flame and lighted cigarettes away . Never
dump benz ine on the ground , into open streams or do wn se w age
drains .
• Be sure to observe all safet y and env ironmental regulations .
Follow all in stru ctions on the conta iner .
• Alway s read and heed all WARNINGS and other info rm ation
=> page 2 52 . •
Chassis
Have the underc oating checked for damage from time to
time.
T he lower body shell of your Audi is also thoroughly protected
against corrosion.
Any damage to the undercoating ca used by r oad ha zards shou ld be
repaired promp tly .
& WARNING
Too much undercoating in the wrong pla ces can cause a fire .
Page 261 of 360
_____________________________________________ C_ l_ e _a_ n_ in_ g_a _ n_d_ p_ r_ o_ t _e_ c_t _io _ n __ lfll
•
& WA RNIN G (continu ed )
• Do not apply additi onal undercoating or ru stproofing on or
ne ar the exhau st manifold , ex haust p ipe s, cat alytic con verter or
heat shields . While driving, the s ub stan ce used for under coating
c ould overhe at and cau se a fire.
• Alway s read a nd heed all WARNINGS and other information
=> page 2 52 . •
Care of interior
A pp lies to veh ic le s: wit h MMI
MMI display
-Cle a n the MMI display with a soft c lean clo th and an LCD
cleane r.
The MM I disp lay can be c leaned with a professionally ava ilable "LCD
cleaner" . Th e cloth should be s lightly dampened with the c leaning
fluid to clean the display.
0 Note
To avoid scratching the MMI display, you should never c lean it dry .•
A pplies to veh ic les : wit h MMI
MMI terminal
- First clean t he MMI terminal with a brush to remove dust
f rom the housing .
- Th en wipe the MMI terminal with a clean, soft, s lig htly
d a mp cloth.
The MM I terminal should be c leaned with a brush first so that no
dirt is trapped between the buttons and the housing . We recom
mend giving the MMI terminal a fina l wipe with a c loth moistened
with wa ter and dish washing detergent .
0 Note
To prevent damage, make sure that no f luid ever gets into the MM I
terminal. •
Aluminum trim
Use only neutral -pH products to remove spo ts and deposits from
a luminum surfaces . Chrome care products and alka line cleaners
wi ll attack aluminum surfaces and can damage them over time .
& WARNING
Alway s re ad and heed all WARNING S and other information
=> page 252.•
Fabrics and fabric coverings
Fabrics and fabric coverings (e .g . seats, door trim pane ls, etc.l
shou ld be c leaned at regular intervals with a vacuum cleaner . T his
removes surface dirt partic les which could become embedded in
the fabric through use . Steam cleaners should not be used, because
the steam tends to push the dirt deeper into the fabric and lock it
there.
Normal cleaning
Generally, we recommend using a soft sponge or a lint -free
microfiber c loth to the clean fabric . Brushes should on ly be used for
carpets and floor mats , since other fabric surfaces could be harmed
by b rushes. .,,
Vehicle care I t •
Page 265 of 360
_____________________________________________ C_ l_ e _a_ n_ in_ g_a _ n_d_ p_ r_ o_ t _e_ c_t _io _ n __ lffllll
•
- Dab at the stain. Start at the outside and work inwards.
- Once the stain is no longer v isible, use a soft dry cloth or
tissue to soak up the moisture.
Do not use lea ther cleaning produc ts on Alcantara®.
You may use a suitable shampoo for removing dust and dirt.
Dust and grit in the pores and seams can scratch and damage the
surface. If the car is left standing in the sun for long periods, the
Alcantara® should be protected against direct sunlight to prevent it
from fading. Slight color variations will develop in normal use and are not an indication of material deterioration.
0 Note
• Never use chemical solvents (e.g. lighter fluid, turpentine),
waxes , shoe polish or similar products on Alcantara ® surfaces.
• To avoid damage, have stubborn stains removed by a commer
cial cleaning specialist.
• Do not use brushes, stiff sponges or similarly abrasive cleaning
aids. •
Safety belts
Only well-maintained safety belts work reliably when
needed.
- Keep belts clean.
- For cleaning, use a mild soap and water solution . Let
belts dry thoroughly and away from direct sunlight.
- Do not allow inertia reel safety belts to retract before
they are completely dry.
- Check the condition of your safety belts
regularly.
Heavily soiled safety belts may not retract properly .
& WARNING
Damaged safety belts can break in a crash.
• Anything that might damage your safety belts could mean that
you and your passengers would not be adequately protected in an
accident.
• Safety belt performance depends on correct installation. Never
remove belts from the vehicle to clean them .
• Do not use chemical cleaning agents, bleach or dyes. They have
corrosive properties which weaken the webbing.
• When cleaning your safety belts, inspect them for damage. If
you discover damage, see your authorized Audi dealer.
• Always read and heed all WARNINGS and other information
=> page 252. •
Engine compartment
Be especially careful when cleaning the engine comport
ment.
Always switch off the ignition before cleaning the engine => &.
Plenum panel
Remove leaves from the plenum panel in front of the windshield
under the engine hood. This prevents the water drain holes from
becoming blocked, and it prevents debris from entering the vehicle
interior through the heating and ventilation ducts .
Corrosion protection
The engine compartment and transmission have been corrosion
protected at the factory.
Good anti-corrosion treatment is very important, particularly in the
winter. If the vehicle is frequently driven on salt treated roads, the .,_
Vehicle care I t •