2010 ASTON MARTIN V8 VANTAGE Sd card

Cooling System (03.03)
Engine (03.00)3-3-6 Workshop Manual Issue 5, Janauary 2010
9. Install grill (refer to Workshop Manual procedure 01.08.AA Grille - Radiator - Renew).
10. Install cooling fan pack (refer to Workshop Manual procedure 03.03.EB Fan and Motor Assembly Radiator -
Renew).
11. Raise vehicle
12. Install bottom radiator cros smember (bolts x4) (torque).
13. Install PAS pipe bracket to cross member (bolt x1).
14. Refill coolant (refer to Workshop Manual procedure 03.03.AD Coolant - Drain and Refill).
Air Conditioning Condenser - Renew
Removal
1. Recover refrigerant gas fr om A/C system (refer to
Workshop Manual procedure 12.03.FA Refrigerant Gas
- Recover/Recharge - Renew).
2. Remove grille (refer to Workshop Manual procedure 01.08.AA Grille - Radiator - Renew).
3. Remove slam panel (screws x12).
4. Remove bolts (x4), that attach the PAS fluid cooler to bonnet latch cross member. Tie fluid cooler aside.
5. Remove bolts (x6), and spacers (x2) that attach the bonnet latch cross member to body and position aside.
6. Remove bolts (x2), that attach the condenser pipe connections. Plug pipes and block connections.
7. Remove and discard O-rings (x2) from pipe connections.
8. Remove bolts (x2), that attach the condenser to radiator, remove condenser.
Installation
1. Install condenser to radiator, install and torque tighten bolts (x2).
2. Clean pipe connections, remove plugs.
3. Install new O-rings to pipe connections. Connect pipes
to condenser. Install and torque tighten bolts (x2).
4. Install bonnet latch cross member, install spacers and bolts (torque).
5. Position PAS fluid cooler to cross member, install and torque tighten bolts (x4).
6. Install slam panel.
7. Install grille (refer to Workshop Manual procedure 01.08.AA Grille - Radiator - Renew). 8. Refrigerant gas re-charge A/C system (refer to Workshop
Manual procedure 12.03.FA Refrigerant Gas - Recover/
Recharge - Renew).
Radiator Fan Modulator - Remove and
Install
Removal
1. Remove the radiator fan and motor assembly. (0303DB - Radiator Fan and Motor Assembly).
2. Disconnect the two electrical connectors from the radiator fan modulator.
3. Release the five fir tree cl ips that attach the wiring
harness for the radiator fan modulator to the fan cowl.
4. Release the two electrical connectors for the radiator fan modulator from the mount.
5. Remove the screw that attaches the radiator fan modulator to the fan cowl.
6. Remove the radiator fan modulator.
Install
1. Install the radiator fan modulator.
2. Install and tighten the screw that attaches the radiator fan modulator to the fan cowl.
3. Attach the two electrical connectors for the radiator fan modulator to the mount.
4. Install the five fir tree clips that attach the wiring harness for the radiator fan modulator to the fan cowl.
5. Connect the two electrical connectors to the radiator fan modulator.
6. Install the radiator fan and motor assembly. (03.03.DB - Radiator Fan and Motor Assembly).
Expansion Tank Assembly - Renew
Remove
1. Using a syringe, remove coolant from expansion tank.
2. Remove bolts (x4), remove LH corner cross brace.
3. Release clips, disconnect coolant hoses (x3) from expansion tank.
4. Remove upper bolt and side nut that attaches the expansion tank.
Repair Operation Time (ROT)
Repair Operation Time (ROT)
ItemCode
Radiator Fan Modulator - Remove and
Install 03.03.EC
Repair Operation Time (ROT)
ItemCode
Expansion Tank Assembly - Renew 03.03.FB
WAR NI NG
DO NOT REMOVE THE PRESSURE CAP WHEN THE
COOLANT IS HOT. ALLOW TIME FOR THE COOLANT /
ENGINE TO COOL. TAKE PARTICULAR CARE TO AVOID BURNS FROM THE COOLING SYSTEM.

Emission Control (03.08)
Engine (03.00)
October 2005 Workshop Manual 3-8-3
2. Disconnect hose from oil separator (quickfit) and
remove.
Installation
1. Install hose to oil separator (quickfit).
2. Connect hose to cam cover (quickfit).
Exhaust Valve to Exhaust Manifold Tube
Assembly-Renew
Removal
1. Raise vehicle on ramp.
2. Remove flange nuts (x2) on RH exhaust manifold. Remove and discard gasket.
3. Lower vehicle.
4. Undo tube union connection (x1) at exhaust valve, remove tube.
Installation
1. Clean flange and pipe connections.
2. Align tube and loosely connect at the valve.
3. Raise vehicle.
4. Fit new gasket to manifold flange.
5. Install tube assembly. install and torque tighten nuts (x2).
6. Lower vehicle on ramp.
7. Torque tighten valve union connection.
Oil Separator to Inlet Manifold Hose-
Renew
Removal
1. Disconnect hose from throttle body adaptor assembly (quickfit).
2. Disconnect hose from PCV valve (quickfit), remove hose.
Installation
1. Install hose to PCV valve (quickfit).
2. Connect hose to throttle body adapter assembly (quickfit).
EGR Module-Renew
Removal
1. Disconnect vacuum tube and multiplug from EGR module. 2. Loosen and disconnect pipe union, EGR module to
exhaust manifold.
3. Remove bolts (x2) securi ng EGR module to inlet
manifold, remove EGR module, discard gasket.
Installation
1. Clean EGR module and mating face on inlet manifold.
2. Install EGR module with new gasket, install and torque tighten bolts (x2).
3. Clean EGR module pipe and union connection.
4. Install and torque tighten pipe union.
5. Connect multiplug and vacuum tube to EGR module.
Repair Operation Time (ROT)
Repair Operation Time (ROT)
Repair Operation Time (ROT)

Engine Sealing (03.10)
Engine (03.00)
Issue 5, Janauary 2010 Workshop Manual 3-10-1
Engine (03.00)
Engine Sealing (03.10)
Specifications
Maintenance
Engine Timing Cover - Renew
1. Remove the front subframe (refer to Workshop Manual procedure 02.01.BA Subframe Assembly - Front -
Remove for Access and Refit).
2. Put an applicable container in position under the engine
to collect drained oil.
3. Remove the sump drain plug and drain the oil from the engine.
4. Remove the oil tank assembly (refer to Workshop Manual procedure 03.02.CA Tank Assembly - Oil
Cooler - Renew).
5. Drain cooling system (refer to Workshop Manual procedure 03.03.AD Coolant - Drain and Refill).
6. Remove the left cam cover (Refer to ’Left Side Cam Cover - Remove and Install’, page 3-10-4) 7. Remove the outer and inner seals from the left cam
cover.
8. Remove the right cam cover (Refer to ’Right Side Cam Cover - Remove and Install’, page 3-10-9).
9. Remove the outer and inner seals from the right cam cover.
10. Release the clips and disconnect the two coolant hoses from the coolant manifold.
11. Release the clip and disconnect the hose from oil the separator.
12. Remove the four M6 Torx screws that attach the coolant manifold to the cylinder heads (Refer to Figure 1).
Figure 1
13. Release the coolant manifold from the coolant pipe.
14. Disconnect the electrical connector for the temperature sensor.
15. Remove the coolant manifold.
16. Remove and discard the two O-rings from the manifold.
17. Loosen the three M6 attachment screws for the water pump pulley (Refer to Figure 2).
Figure 2
18. Turn the auxiliary drive be lt tensioner to release the
tension from the drive belt.
19. Remove the drive belt.
20. Remove the three M6 screws that attach the water pump pulley and remove the pulley.
Torque Figures
DescriptionNm.lb./ft.
Cam cover 10 7
Dipstick tube 6 4
Timing cover:
Bolts 1 to 7, 9 to 18 and 20 to 27
Bolts 8 and 19
12

10
9

7
Crankshaft pulley bolt 320 236
Alternator mounting bracket 21 15.5
Alternator 40 30
Coolant manifold 9 6.5
Coolant pump 12 9
Coolant pump pulley 10 + 45° 7 + 45°
PAS pump 21 15.5
Accessory drive belt idler pulleys 40 30
Accessory drive be lt tensioner 40 30
Heater hose brackets:
M6 Bolts
M5 Nuts
12

5
9

3.7
Harness support brackets:
M5 Nut
M6 Screw
M8 Screw
5

10
25
3.7

7
18.5
Repair Operation Time (ROT)
A030368
A030553A

Engine Sealing (03.10)
Engine (03.00)3-10-2 Workshop Manual Issue 5, Janauary 2010
21. Remove the M10 bolt that attaches the auxiliary drive belt tensioner and remove tensioner (Refer to Figure 3).
Figure 3
22. Remove the two bolts that attach the inspection cover to lower crankcase and remove the cover.
23. Install the tool (303-1185) to hold the flywheel. Install and tighten the two bolts.
24. Remove and discard the M16 screw that attaches the crankshaft pulley.
25. Install the thrust-button of tool (303 -1186) into crankshaft.
26. Put the tool into the pulley.
27. Attach the tool with the two bolts.
28. Turn the centre bolt clockwise to withdraw the pulley from the crankshaft.
29. Collect the crankshaft pulley, locking ring and the thrust button for the special tool.
30. Remove the special tool from the pulley.
31. Remove and discard the O-ring seal from the pulley.
32. Remove the bolt that attaches the alternator idler pulley and remove the pulley.
33. Remove the bolt that attaches the idler pulley for the air- conditioning compressor and remove the pulley.
34. Put an applicable container under the oil filter to collect drained oil.
35. Remove the oil filter.
36. Release the oil separator drain tube from the timing cover.
37. Release the clip for the oil separator drain tube from the bracket.
38. Release the cover for the battery cable from the alternator. 39. Remove the nut that attaches the battery cable to the
alternator and remove the cable. (Refer to Figure 4).
Figure 4
40. Disconnect the electrical connector from the alternator.
41. Remove the M8 bolt that attaches the top of the alternator.
42. Remove the M10 bolt and the nut that attaches the bottom of the alternator and remove the alternator.
43. Remove the three Torx bolts that attach the alternator mounting bracket to the cylinder block.
44. Remove the bracket (Refer to Figure 5).
Figure 5
45. Remove the three M8 bolts that attach the PAS pump to the mounting bracket and move the pump away.
WAR NI NG
DO NOT GET USED ENGINE OIL ON YOUR SKIN.
USED ENGINE OIL CAN BE HARMFUL.
A030553A030582
A0310242

Engine Sealing (03.10)
Engine (03.00)
Issue 5, Janauary 2010 Workshop Manual 3-10-5
22. Remove and discard the seals for the 14 cam cover screws.
23. Remove the cam cover.
24. Remove the breather pipe stub.
25. Remove and discard the seal for the breather pipe stub.
26. Remove and discard the O-ring seal for the VVT
solenoid.
27. Remove and discard the cam cover gasket.
28. Remove and discard the four O-ring seals from the spark plug wells.
29. Clean the component mating faces.
Install
1. Install four new O-ring seals in the spark plug wells.
2. Install a new O-ring seal for the VVT solenoid.
3. Install a new cam cover gasket.
4. Install a new seal for the breather pipe stub.
5. Install the breather pipe stub.
6. Apply a 6 mm diameter sphere of silicon RTV sealant at the positions shown in Figure C03-10-102.
Figure C03-10-102
7. Install the cam cover.
8. Install new seals for the 14 cam cover screws.
9. Install and torque the 14 screws that attach the cam cover to the engine in the sequence shown to 10 Nm.
Figure C03-10-051
10. Install the four ignition coils. 11. Install and torque the screw that attaches each of the
four ignition coils to 5 Nm.
12. Install the front bracket for the wiring harness.
13. Install the rear bracket for the wiring harness.
14. Install and torque the three screws that attach the rear bracket for the wiring harness to 11 Nm.
15. Install and tighten the two nuts and three bolts that attach the front bracket for the wiring harness.
16. Install the purge pipe and he ater pipe into the two clips
on the wiring harness bracket.
17. Use four applicable cable ties to attach the rear of the wiring harness to the front bracket.
18. Install the wiring harness for the injectors into the mounts.
19. Install the fir tree clip that attaches the wiring harness for the ignition coils.
20. Connect the electrical connector to each of the four ignition coils.
21. Connect the electrical connector to the VVT solenoid.
22. Install the ignition coil cover.
23. Remove and discard the caps from the breather pipes.
24. Connect the breather pipes to the cam cover and the oil tank Y-piece.
25. Install the left side front crush bar for the body reinforcement. (Refer to procedure 01.01.AC - Left Side
Front Crush Bar for the Body Reinforcement).
26. Install the front crush brace. (Refer to procedure 01.01.LC - Front Crush Brace).
27. Connect the battery earth cable
Left Side Cam Cover Gasket - Renew
Removal
1. Remove the left cam cover (Refer to ’Left Side Cam Cover - Remove and Install’, page 3-10-4).
2. Remove and discard the cam cover gasket.
Installation
1. Clean the mating faces of the cam cover and the cylinder head.
2. Put the new cam cover gasket in position.
3. Install the left cam cover (Refer to ’Left Side Cam Cover - Remove and Install’, page 3-10-4).
CAUTION
Tighten the screws gradually and equally in the step
that follows. If you do not, the cam cover gasket can be
damaged.
C03-10-102
CAUTION
M a k e s u re th a t th e ve h i c le i s o n i t s r o a d w h e el s on l ev e l
ground when you do the do the steps that folllow. If you
do not, the front of the vehicle can be twisted when the cross brace is tightened.
Repair Operation Time (ROT)

Engine Sealing (03.10)
Engine (03.00)3-10-6 Workshop Manual Issue 5, Janauary 2010
Right Side Cam Cover Gasket - Renew
1. Remove the right cam cover (Refer to ’Right Side Cam Cover - Remove and Install’, page 3-10-9).
2. Remove and discard the cam cover gasket.
Installation
1. Clean the mating faces of the cam cover and the cylinder head.
2. Put the new cam cover gasket in position.
3. Install the right cam cover (Refer to ’Right Side Cam
Cover - Remove and Install’, page 3-10-9).
Cylinder Head Gasket - Renew (Engine
Set)
Removal
1. Remove the SAI pump and bracket assembly (refer to procedure 03.08.DB Pump and Bracket Assembly -
Secondary Air Injection - Renew).
2. Disconnect the electrical connector from each of the two left and two right knock sensors.
3. Disconnect the electrical connector from the left and right camshaft timing sensors.
4. Remove the right exhaust manifold (refer to procedure 09.00.CC Gasket - Exhaust Manifold - RH - Renew).
5. Remove the left front wheel arch liner (refer to procedure 01.02.FB Wheel Arch Liner - Front - LH -
Renew).
6. Remove the eight nuts that attach the left exhaust manifold to cylinder head.
7. Remove the left exhaust ma nifold. Remove and discard
the gasket.
8. Remove the left intake camshaft (refer to Workshop Manual procedure 03.09.AV Camshaft - Intake - LH -
Renew). 9. Remove the 10 left exhaust camshaft bearing cap
attachment bolts evenly and in steps (refer to Figure 1).
Figure 1
10. Record the positions and the markings of the bearing caps for the left exhaust camshaft .
11. Remove the bearing caps for the left exhaust camshaft.
Figure 2
12. Remove the two bolts that attach the front end of the left cylinder head to the cylinder block.
Repair Operation Time (ROT)
Repair Operation Time (ROT)
A0309270
A0309272

Engine Sealing (03.10)
Engine (03.00)
Issue 5, Janauary 2010 Workshop Manual 3-10-7
13. Remove the 10 bolts evenly and in steps, that attach the left cylinder head to the cylinder block (refer to Figure
3).
Figure 3
14. With the aid of one more person, remove the left cylinder head assembly.
15. Remove and discard the cylinder head gasket.
16. Remove the two Torx bolts, the spacer on the exhaust and the Torx bolt that attaches the right intake and
exhaust camshaft sprockets to the camshafts (refer to
Figure 4).
Figure 4
17. Remove the two bolts that attach the right secondary timing chain tensioner to the cylinder head (refer to
Figure 5).
Figure 5
18. Remove the right camshaft sp rockets complete with the
timing chain and tensioner from the camshafts (refer to
Figure 6).
Figure 6
19. Remove the three bolts that attach tool (303-530) to the cylinder head. Remove the special tool (refer to Figure
7).
Figure 7
A0310319
A0309252
A0309253
A0309254
A0309271

Engine Sealing (03.10)
Engine (03.00)3-10-8 Workshop Manual Issue 5, Janauary 2010
20. Remove the ten bolts evenly and in steps, that attach the bearing caps for the right intake camshaft (refer to
Figure 8).
Figure 8
21. Record the positions and the markings of the bearing caps for the right intake camshaft.
22. Remove the right intake camshaft (refer to Figure 9).
Figure 9
23. Remove the ten bolts evenly and in steps, that attach the bearing caps for the right exhaust camshaft (refer to
Figure 10).
Figure 10
24. Record the positions and the markings of the bearing caps for the right exhaust camshaft.
25. Remove right exhaust camshaft (refer to Figure 11).
Figure 11
26. Remove the two bolts that attach the front end of the right cylinder head to the cylinder block.
27. Remove the ten bolts evenly and in steps, that attach the right cylinder head to the cylinder block (refer to
Figure 12).
Figure 12
28. With the aid of one more person, remove the right cylinder head assembly.
29. Remove and discard the cylinder head gasket.
Installation
1. Fully clean the left and right cylinder head faces and the attachment bolt pockets.
2. Fully clean the left and right cylinder block faces.
3. Fully clean and dry the left and right cylinder head retaining bolts.
4. Install a new right cylinder gasket. Make sure that it is correctly engaged on the dowels.
5. With assistance, install the right cylinder head. Make sure it is correctly engaged on the dowels.
6. Install and torque tighten the 12 cylinder head bolts in the correct sequence.
7. Lubricate the camshaft journals, camshaft lobes, bearing surfaces on cylinder head and the bearing caps with
clean engine oil.
A0309258
A0309259
A0309258
A0309260
A0310319