2010 ASTON MARTIN V8 VANTAGE wheel

Silencer Assembly (09.01)
Exhaust (09.00)9-1-6 Workshop Manual Issue 5, January 2010
2. Clean silencer and mating faces on rear pipes.
3. Remove Rear RH wheel arch liner (refer to Workshop Manual procedure 01.02.HB Wheel Arch Liner - Rear -
RH - Renew).
4. Remove rear undertray (refer to Workshop Manual procedure 01.02.PB Undertray - Rear - Renew).
5. Apply a proprietary exhaust sealant around all clamp joints
6. Remove Allen bolts (x2), loosen Allen bolts (x2), bumper diffuser to mounting brackets and remove diffuser.
7. Position silencer on lifter.
8. Install silencer, position rear hangers to body, install and torque tighten bolts (x4).
9. Remove Rear LH wheel arch liner.
10. Disconnect both by-pass valve vacuum lines.
11. Remove Allen bolts (x2), loosen Allen bolts (x2), bumper diffuser to mounting brackets and Remove diffuser.
12. Position front mountings to subframe, install and torque tighten bolts (x4).
13. Loosen clamp nuts (x2), remove stub pipes (x2).
14. Disconnect both by-pass valve vacuum lines.
15. Align silencer to rear pipes, install springs onto bolts (x4), install and torque tighten bolts (x4).
16. Remove bolts (x4), rear exha ust pipes to silencer. Collect
springs from bolts.
17. Loosen clamp nuts (x2), remove stub pipes (x2).
18. Install stub pipes (x2), centralise stub pipes to exhaust trim finisher. Torque ti ghten clamp nuts (x2).
19. Remove bolts (x4), securing LH and RH silencer rear
hanger brackets to body.
20. Remove bolts (x4), rear exhaust pipes to silencer and collect springs from bolts.
21. Check silencer to rear pipes for correct alignment and clearances.
22. Remove bolts (x4), silencer front mountings to subframe.
23. Remove bolts (x4), securing LH and RH silencer rear
hanger brackets to body.
24. Connect lines to both by-pass vacuum valves.
25. Position suitable lifter to support weight of silencer.
With assistance, remove silencer.
26. Remove bolts (x4), silencer front mountings to subframe.
27. Install rear bumper diffuser and install and tighten Allen
bolts (x4).
28. Install Rear RH wheel arch liner (refer to Workshop Manual procedure 01.02.HB Wheel Arch Liner - Rear -
RH - Renew).
Installation
1. Position suitable lifter to su pport weight of silencer. With
assistance, remove silencer.
2. Clean silencer and mating faces on rear pipes.
3. Install Rear LH wheel arch liner.
4. Apply a proprietary exhaust sealant around all clamp joints 5. Lower vehicle on ramp.
6. Position silencer on lifter. Install silencer, position rear
hangers to body, install and torque tighten bolts (x4).
7. Position front mountings to subframe, install and torque tighten bolts (x4).
8. Align silencer to rear pipes, install springs onto bolts (x4), install and torque tighten bolts (x4).
9. Install stub pipes (x2), centralise stub pipes to exhaust trim finisher and torque tighten clamp nuts (x2).
10. Check silencer to rear pipes for correct alignment and clearances.
11. Connect lines to both by-pass vacuum valves.
12. Install rear bumper diffuser and install and tighten Allen bolts (x4).
13. Install rear undertray (r efer to Workshop Manual
procedure 01.02.PB Undertray - Rear - Renew).
14. Lower vehicle on ramp.
Silencer and Bypass Valve Assembly-
Renew
Removal
1. Raise vehicle on ramp.
2. Coupe Only - Remove rear undertray (refer to
Workshop Manual procedure 01.02.PB Undertray -
Rear - Renew).
3. Roadster Only - Remove RH rear wheel arch liner (refer
to Workshop Manual procedure 01.02.HB Wheel Arch
Liner - Rear - RH - Renew).
4. Roadster Only - Remove LH rear wheel arch liner.
5. Remove Allen bolts (x2, loosen Allen bolts (x2), securing bumper diffuser to mounting brackets. Remove diffuser.
6. Disconnect both by-pass valve vacuum lines.
7. Loosen clamp nuts (x2), remove stub pipes (x2).
8. Remove bolts (x4), rear exha ust pipes to silencer. Collect
springs from bolts.
9. Remove bolts (x4), securing LH and RH silencer rear
hanger brackets to body.
10. Remove bolts (x4), muffler front mountings to subframe. Remove mountings from silencer.
Repair Operation Time (ROT)
ItemCode
Silencer and Bypass Valve Assembly-
Renew 09.00.KB
WAR NI NG
THE EXHAUST SYSTEM WILL BE VERY HOT AFTER
OPERATION. LET THE EXHA UST COOL BEFORE YOU
DO WORK. IF YOU DO NO T, PESONAL INJURY CAN
OCCUR.
WAR NI NG
GET THE AID OF ONE MORE PERSON WHEN YOU
REMOVE THE REAR EXHAUST SILENCER.
THE SILENCER IS HEAVY .

Silencer Assembly (09.01)
Exhaust (09.00)
Issue 5, January 2010 Workshop Manual 9-1-7
11. Position suitable lifter to support weight of silencer.
With assistance, remove silencer.
12. Remove both rear rubber mountings and hanger brackets from silencer.
Installation
1. Clean silencer and mating faces on rear pipes and stub pipes.
2. Install both rear rubber mountings and hanger brackets to silencer.
3. Position silencer on lifter . Install silencer, position
hangers, install and tighten bolts (x4).
4. Install front mountings to silencer, install and tighten bolts (x4).
5. Align silencer to rear pipes. Install springs (x4), and torque tighten bolts (x4).
6. Install and align stub pipes (x2) to silencer and trims in bumper. Align and tighten clamp bolts.
7. Check silencer to rear pipes for correct alignment and clearances.
8. Install stub pipes (x2), insta ll clamps (x2), centralise stub
pipes to exhaust trim finisher, torque tighten clamp nuts
(x2).
9. Check silencer to rear pipes for correct alignment and clearances.
10. Connect lines to both by-pass vacuum valves.
11. Install rear bumper diffuse r. Install and tighten Allen
bolts (x4).
12. Roadster Only - Install RH rear wheel arch liner (refer to
Workshop Manual procedure 01.02.HB Wheel Arch
Liner - Rear - RH - Renew).
13. Roadster Only - Install LH rear wheel arch liner.
14. Coupe Only - Install rear undertray (refer to Workshop
Manual procedure 01.02.PB Undertray - Rear - Renew).
15. Lower vehicle on ramp.
Exhaust Rear Silencer Mounting Rubber-
Renew
Removal
1. Raise vehicle on ramp. 2. Remove Allen bolts (x4), bumper diffuser to mounting
brackets. Remove diffuser, collect mounting brackets.
3. Remove bolts (x2), securing silencer rear hanger brackets to body.
4. Release/remove rubber mounting and hanger bracket from silencer bracket.
5. Remove rubber mounting from hanger bracket.
Installation
1. To aid assembly, apply liquid soap to rubber mounting .
2. Install rubber mounting on hanger bracket.
3. Install rubber mounting on muffler bracket.
4. Align hanger bracket to body, install and torque tighten bolts (x2).
5. Position mounting brackets, install bumper diffuser, install and torque tighten Allen bolts (x4).
6. Lower vehicle on ramp.
Exhaust System-Renew
1. Disconnect vehicle battery.
2. Raise vehicle on ramp.
3. Remove RH exhaust manifold.
4. Remove RH front wheel arch liner (refer to Workshop Manual procedure 01.02.GB Wheel Arch Liner - Front -
RH - Renew).
5. Remove LH front wheel arch liner (refer to Workshop
Manual procedure 01.02.FB Wheel Arch Liner - Front -
LH - Renew).
6. Remove heatshield deflector, front floor (refer to Workshop Manual procedure 09.04.AA Heatshield -
Front Floor - Renew).
7. Loosen EGR pipe in valve.
8. Remove (nuts x2) EGR pipe from manifold, discard
gasket and tie aside.
WA R N I N G
GET THE AID OF ONE MORE PERSON WHEN YOU INSTALL THE REAR EXHAUST SILENCER.
THE SILENCER IS HEAVY .
Ensure correct alignment of exhaust pipes and silencer before tightening of fixing clamps.
Repair Operation Time (ROT)
WA R N I N G
THE EXHAUST SYSTEM WILL BE VERY HOT AFTER
OPERATION. LET THE EXHAUST COOL BEFORE YOU DO WORK. IF YOU DO NO T, PESONAL INJURY CAN
OCCUR.
Repair Operation Time (ROT)

Silencer Assembly (09.01)
Exhaust (09.00)9-1-8 Workshop Manual Issue 5, January 2010
9. Remove nut (x8) securing RH exhaust manifold to cylinder head (refer to Fig. 1).
10. Remove nut (x2) on RH engine mounting.
11. Raise engine by approximately 25mm.
12. Remove RH exhaust manifold from vehicle and discard
gasket.
13. Remove heatshield from manifold (bolts x4)
14. Remove nuts (x8) securing LH exhaust manifold to
cylinder head.
15. Remove exhaust manifold, remove and discard gasket.
Installation
1. Clean LH exhaust manifold and mating face on cylinder head. Install new manifold gasket.
2. Install LH exhaust manifold to cylinder head.
3. Install and torque tighten nuts (x8) securing exhaust manifold to cylinder head.
4. Clean exhaust manifold and mating face on engine. Install new gasket to engine.
5. Install heatshield to manifold (bolts x4)
6. Install RH exhaust mani fold to cylinder head.
7. Install nut (x8) securing manifold to cylinder head
(torque).
8. Lower engine.
9. Install nuts (x2) on engine mounts (torque).
10. Install (nuts x2) EGR pipe from manifold, clean mating face and fit new gasket (torque).
11. Install heatshield deflector, front floor (refer to Workshop Manual procedure 09.04.AA Heatshield -
Front Floor - Renew).
12. Tighten EGR pipe in valve (torque).
13. Install RH front wheel arch liner (refer to Workshop Manual procedure 01.02.GB Wheel Arch Liner - Front -
RH - Renew
14. Install LH wheel arch liner (refer to Workshop Manual procedure 01.02.FB Wheel Arch Liner - Front - LH -
Renew).
15. Lower vehicle on ramp. 16. Connect vehicle battery.
Exhaust System (Excluding Manifold/
Downpipes)-Renew
Removal
1. Raise vehicle on ramp.
2. Remove undertrays - vehicle set (refer to Workshop
Manual procedure 01.02.PD Undertrays - Vehicle Set -
Renew).
3. Remove Allen bolts(x4), bumper diffuser to mounting brackets. Remove diffuser
4. Disconnect both by-pass valve vacuum lines.
5. Remove bolts (x4), securing LH and RH silencer rear
hanger brackets to body. Remove hanger brackets.
6. Remove bolts (x4), rear exha ust pipes to silencer. Collect
springs from bolts
7. Remove bolts (x4), silencer front mountings to subframe. Remove mountings from silencer.
8. Position suitable lifter to support weight of silencer. with assistance, remove silencer.
9. Mark rear stub pipes to si lencer for assembly purposes.
10. Loosen clamps (x2), rear stub pipes to silencer. Remove stub pipes and clamps.
11. Remove bolts (x4), remove rear subframe cross brace.
12. Loosen clamps (x2), release RH and LH rear pipes from centre pipe.
13. Remove rear pipes through subframe.
14. Loosen clamps (x2), centre pipe to LH and RH catalysts.
15. Coupe Only - Release centre pipe from mountings, LH
and RH catalysts, remove centre pipe.
16. Roadster Only - Remove centre exhaust mounting bolts
(x4).
17. Release LH and RH catal ysts, remove centre pipe.
18. Disconnect multiplugs (x4), from each catalyst.
19. Coupe Only - Secure sufficient lengths of string to
HEGO sensor multiplugs for assembly purposes.
Figure 1
A090069
Repair Operation Time (ROT)
ItemCode
Exhaust System (Excluding Manifold/
Downpipes)-Renew 09.00.NB
WAR NI NG
TO AVOID PERSONAL INJURY, I.E. SEVERE BURNS TO
THE SKIN, ALLOW EXHAUS T SYSTEM TO COOL
DOWN BEFORE REMOVING EXHAUST SYSTEM COMPONENTS.
WAR NI NG
GET THE AID OF ONE MORE PERSON WHEN YOU
REMOVE THE REAR EXHAUST SILENCER.
THE SILENCER IS HEAVY .
Attach lengths of string to th e HEGO sensor multiplugs. This
enables routing the HEGO sensor harness behind the exhaust heat shield on assembly.

Pipes and Supports (09.03)
Exhaust System (09.00)9-2-2 Workshop Manual May 2007
5. Install centre pipe to both catalysts and centre mountings. Do not torque clamp nuts at this stage.
6. Install pipe assembly exha ust rear - LH (refer to
Workshop Manual procedure 09.00.JB Pipe Assembly -
Exhaust - Rear - LH - Renew).
7. Install pipe assembly exhaust rear - RH (refer to Workshop Manual procedure 09.00.HB Pipe Assembly
- Exhaust - Rear - RH - Renew).
8. Align and torque tighten exhaust system nuts/bolts.
9. Lower vehicle on ramp.
RH Exhaust Manifold-Renew
Removal
1. Disconnect vehicle battery.
2. Raise vehicle on ramp.
3. Remove RH front wheel arch liner (refer to Workshop Manual procedure 01.02.GB Wheel Arch Liner - Front -
RH - Renew).
4. Loosen EGR pipe in valve.
5. Remove heatshield deflector, front floor (refer to Workshop Manual procedure 09.04.AA Heatshield -
Front Floor - Renew).
6. Remove (nuts x2) EGR pipe from manifold, discard
gasket and tie aside.
7. Remove nut (x8) securing manifold to cylinder head
(refer to Fig. 1).
8. Remove nut (x2) on engine mountings.
9. Raise engine by approximately 25mm. 10. Remove exhaust manifold from vehicle and discard
gasket.
11. Remove heatshield from manifold (bolts x4)
Installation
1. Clean exhaust manifold and mating face on engine. Install new gasket to engine.
2. Install heatshield to manifold (bolts x4)
3. Install manifold to engine.
4. Install nut (x8) securing manifold to cylinder head.
5. Lower engine.
6. Install nuts (x2) on engine mounts.
7. Install (nuts x2) EGR pipe from manifold, clean mating face and fit new gasket (torque).
8. Install heatshield deflector, front floor (refer to Workshop Manual procedure 09.04.AA Heatshield -
Front Floor - Renew).
9. Tighten EGR pipe in valve (torque).
10. Install RH front wheel arch liner (refer to Workshop
Manual procedure 01.02.GB Wheel Arch Liner - Front -
RH - Renew).
11. Lower vehicle on ramp.
12. Connect vehicle battery.
LH Exhaust Manifold-Renew
Removal
1. Disconnect vehicle battery.
2. Raise vehicle on ramp.
3. Remove heatshield deflec tor, front floor (refer to
Workshop Manual procedure 09.04.AA Heatshield -
Front Floor - Renew).
4. Remove LH front wheel arch liner (refer to Workshop Manual procedure 01.02.FB Wheel Arch Liner - Front -
LH - Renew).
Repair Operation Time (ROT)
A090069
Repair Operation Time (ROT)
ItemCode
Exhaust Manifold-Renew LH09.00.CB
WAR NI NG
TO AVOID PERSONAL INJURY, I.E. SEVERE BURNS TO
THE SKIN, ALLOW EXHAUS T SYSTEM TO COOL
DOWN BEFORE REMOVING EXHAUST SYSTEM COMPONENTS.

Pipes and Supports (09.03)
Exhaust System (09.00)
May 2007 Workshop Manual 9-2-3
5. Remove nuts (x8), securing manifold to cinder head
(refer to Fig. 1).
6. Remove exhaust manifold, remove and discard gasket.
Installation
1. Clean manifold and mating face on engine and install
new gasket to engine.
2. Install manifold to engine.
3. Install nuts (x8) securing manifold to cylinder head.
4. Install LH front wheel arch liner (refer to Workshop Manual procedure 01.02.FB Wheel Arch Liner - Front -
LH - Renew).
5. Install heatshield deflector, front floor (refer to Workshop Manual procedure 09.04.AA Heatshield -
Front Floor - Renew).
6. Lower vehicle on ramp.
7. Connect vehicle battery.
RH Exhaust Manifold Gasket-Renew
Removal
1. Remove wheel arch liner (refer to Workshop Manual procedure 01.02.GB Wheel Arch Liner - Front - RH -
Renew).
2. Loosen EGR pipe in valve.
3. Remove heatshield deflector, front floor (refer to Workshop Manual procedure 09.04.AA Heatshield -
Front Floor - Renew).
4. Remove nuts (x2), EGR pipe to manifold, discard gasket
and tie EGR pipe aside. 5. Remove nut (x8) securing ex
haust manifold to cylinder
head.
6. Remove nuts (x2) on engine mountings.
7. Raise engine by approximately 25mm. (care to be taken as inlet manifold can foul).
8. Remove exhaust manifold from vehicle and discard gasket.
Installation
1. Install new gasket to engine, clean mating face on engine.
2. Install manifold to engine.
3. Install nut (x8) securing manifold to cylinder head
(torque).
4. Lower engine.
5. Install nuts (x2) on engine mounts (torque).
6. Install (nuts x2) EGR pipe from manifold, clean mating face and fit new gasket (torque).
7. Install heatshield deflector, front floor (refer to Workshop Manual procedure 09.04.AA Heatshield -
Front Floor - Renew).
8. Tighten EGR pipe in valve (torque).
9. Install wheel arch liner (r efer to Workshop Manual
procedure 01.02.GB Wheel Arch Liner - Front - RH -
Renew).
LH Exhaust Manifold Gasket-Renew
Removal
1. Remove heatshield deflector, front floor (refer to Workshop Manual procedure 09.04.AA Heatshield -
Front Floor - Renew).
2. Remove LH wheel arch liner (refer to Workshop Manual procedure 01.02.FB Wheel Arch Liner - Front - LH -
Renew).
3. Remove nut (x8) securing manifold to cylinder head.
4. Remove manifold from vehicle and discard gasket.
Installation
1. Install new gasket to engine, clean mating face on engine.
2. Install manifold to engine.
3. Install nut (x8) securing manifold to cylinder head
(torque).
4. Install LH wheel arch liner (refer to Workshop Manual procedure 01.02.FB Wheel Arch Liner - Front - LH -
Renew).
Fig. 1
Repair Operation Time (ROT)
302306BA090070
Repair Operation Time (ROT)

Fuel Tank and Lines (10.01)
Fuel (10.00)
May 2007 Workshop Manual 10-1-17
2. Remove RH front wheel arch liner (see Workshop Manual procedure 01.02.GB Wheel Arch Liner - Front -
RH - Renew).
3. Disconnect quick fit connector fuel vapour pipe to tank.
4. Release fuel vapour pipe from fuel line clips (x4).
5. Disconnect quick fit conne ctor fuel vapour pipe
assembly to purge valve T-piece.
6. Remove fuel vapour pipe.
Installation
1. Install fuel vapour pipe and connect to purge valve 'T' piece.
2. Position fuel vapour pi pe in vapour line clips.
3. Connect fuel vapour pipe to fuel tank.
4. Install RH front wheel arch liner (see Workshop Manual procedure 01.02.GB Wheel Arch Liner - Front - RH -
Renew).
5. Battery isolation switch on.
Fuel Supply and Vapour Pipe Assembly-
Renew
Removal
1. Depressurise fuel system (see Workshop Manual procedure 10.01.EK Fuel System - Depressurise).
2. Disconnect vehicle battery. 3. Remove RH front wheel arch liner (see Workshop
Manual procedure 01.02.GB Wheel Arch Liner - Front -
RH - Renew).
4. Position container to collect spillage from fuel supply pipe.
5. Disconnect quick fit connect or fuel supply pipe to tank
6. Release pipe assembly fr om fuel line clips (x3).
7. Disconnect quick fit connect or fuel supply to manifold
supply (fuel rail) and re move pipe assembly.
Installation
1. Connect fuel supply pipe to manifold supply pipe.
2. Position fuel line in fuel line clips (x3).
3. Connect fuel supply pipe to tank.
4. Install RH front wheel arch liner (see Workshop Manual procedure 01.02.GB Wheel Arch Liner - Front - RH -
Renew).
5. Connect vehicle battery.
Manifold Supply Fuel Pipe Assembly-
Renew
Removal
1. Depressurise fuel system (see Workshop Manual procedure 10.01.EK Fuel System - Depressurise).
Warning
Fuel vapour is explosive. During the following
procedure, fuel tank and fuel lines will be open. Ensure
good ventilation and take all necessary precautions to
eliminate fire risk.
Warning
Fire Risk. Do Not start the en gine until the fuel system
integrity is confirmed.
Repair Operation Time (ROT)
Warning
Read and follow all fuel hand ling instructions (at the
beginning of the Fuel System section) and the fuel
bowser manufacturers fuel handling documentation
before commencing work on the fuel system. Clean up
spillages immediatel y and dispose of fuel contaminated
materials safely.
Warning
Fire Risk. Before commencing work on the vehicle fuel system, disconnect the earth ( - ve) lead from the vehicle battery.
Warning
Fuel vapour is explosiv e. During the following
procedure, fuel tank and fuel lines will be open. Ensure
good ventilation and take all necessary precautions to
eliminate fire risk.
Warning
Fire Risk. Do Not connect the vehicle battery and
switch on the ignition until all work on the fuel system
is completed and the area is cleared of fuel
contamination.
Remove contaminated material, open fuel containers
and waste fuel. Fully ventilate vehicle and work area to remove all fuel fumes.
Warning
Fire Risk. Do Not start the en gine until the fuel system
integrity is confirmed.
Repair Operation Time (ROT)
Warning
Read and follow all fuel hand ling instructions (at the
beginning of the Fuel System section) and the fuel
bowser manufacturers fuel handling documentation
before commencing work on the fuel system. Clean up
spillages immediately and dispose of fuel contaminated materials safely.
Warning
Fire Risk. Before commencing work on the vehicle fuel system, disconnect the earth ( - ve) lead from the vehicle battery.

Fuel Tank and Lines (10.01)
Fuel (10.00)10-1-18 Workshop Manual May 2007
2. Disconnect vehicle battery
3. Remove RH wheel arch liner (see Workshop Manual
procedure 01.02.GB Wheel Arch Liner - Front - RH -
Renew).
4. Position container to collect fuel spillage.
5. Release fuel supply and vapour pipe from pipe clips (3).
6. Disconnect quick fit connector manifold supply pipe to fuel supply and vapour pipe.
7. Disconnect manifold supp ly pipe from fuel rail.
8. Release manifold supply pipe from pipe clips (x3) and
remove pipe.
Installation
1. Position manifold supply pipe and secure in clips (x3).
2. Connect manifold supply pipe to fuel rail.
3. Connect manifold supply pipe to fuel supply and vapour
pipe.
4. Secure fuel supply and vapour pipe in clips (x3).
5. Install wheel arch liner (see Workshop Manual procedure 01.02.GB Wheel Arch Liner - Front - RH -
Renew).
6. Connect vehicle battery.
Warning
Fire Risk. Do Not connect the vehicle battery and
switch on the ignition until all work on the fuel system
is completed and the area is cleared of fuel
contamination.
Remove contaminated material, open fuel containers
and waste fuel. Fully ventilat e vehicle and work area to
remove all fuel fumes.
Warning
Fire Risk. Do Not start the en gine until the fuel system
integrity is confirmed.

Issue 5, January 2010 Workshop Manual 11-1-1
Steering (11.00)
Contents
Steering Gear (11.01) .......................................... 11-1-2Diagnostics - Symptom Chart................................. 1-2
Specifications.......................................................... 1-4
Power Steering (11.02) ........................................ 11-2-1 Description ............................................................. 2-1
Specifications.......................................................... 2-1
Maintenance ........................................................... 2-2Power Steering System - Bleed ............................... 2-2
Procedure .............................................................. 2-2
Power Steering Pump-Renew ................................. 2-2
Power Assisted Steering (PAS) Rack -
Remove and Install................................................. 2-2
RH/LH Track Rod End-Renew .............................. 2-11
Power Steering Pump to Rack Hose Assembly
-Renew ................................................................ 2-11
Power Steering Rack to Cooler Hose-Renew ........ 2-12
Steering Column (11.04)...................................... 11-4-1 Description ............................................................. 4-1
Specifications.......................................................... 4-1
Maintenance ........................................................... 4-1Top Shroud for the Steering Column
- Remove and Install .............................................. 4-1
Bottom Shroud for the Steering Column
- Remove and Install .............................................. 4-1
Steering Column Gaiter-Renew .............................. 4-2
Upper Steering Column Assembly-Renew .............. 4-3
Top and Bottom Shrouds for the Steering Column
- Remove and Install .............................................. 4-4
Steering Column Lower Shaft Assembly-Renew ...... 4-5
Steering Column Switches (11.05)....................... 11-5-1 Maintenance ........................................................... 5-1Ignition Switch-Renew (Pre-08 MY Only) ............... 5-1
Steering Column Stalk Assembly Switch-Renew
(Pre-08 MY Only) ................................................... 5-1
Cruise Control Switch-Renew................................. 5-2
Indicator Switch for the Steering Column
- Remove and Install .............................................. 5-2
Airbag Rotary Coupler Assembly - Remove and
Install ..................................................................... 5-2
Wiper Switch for the Steering Column
- Remove and Install .............................................. 5-4
Steering Wheel (11.06) ........................................ 11-6-1 Specifications.......................................................... 6-1
Maintenance ........................................................... 6-1Steering Wheel-Renew .......................................... 6-1
Driver’s Airbag Module - Remove and Install .......... 6-1