2010 Alfa Romeo GT alarm

GETTING TO KNOW YOUR CAR
7
IMPORTANTTo guarantee the perfect
efficiency of the electronic devices contained
in keys, avoid letting them directly exposed
to sunrays.
Together with the keys the CODE card is
provided (for versions/ markets where ap-
plicable) (fig. 3), bearing in print the key
codes (both mechanical and electronic for
emergency start up).
The code numbers on the CODE card must
be kept in a safe place , not in the car.The driver should always keep the elec-
tronic CODE card with him/her in the event
of having to carry out emergency starting.KEY WITH REMOTE CONTROL
The key with remote control (fig. 4) is
fitted with:
– a metal insert (A) that can be enclosed
in the key grip
– a button (B) for power-assisted open-
ing of the metal insert
– a button (C) for remote door unlock-
ing and at the same time switching off the
electronic alarm
– a button (D) for remote door locking
and at the same time switching on the elec-
tronic alarm
– a button (E) for remote boot unlocking
– removable hook ring (F).
fig. 3
A0A0003b
If the car changes owner,
the new owner must be
given all the keys and the
CODE card.
fig. 4
A0A0600b

GETTING TO KNOW YOUR CAR
8
The button B should only
be pressed when the key is
away from the body, in
particular from the eyes, and from
objects that can be spoilt (clothes
for instance). Make sure the key
can never be touched by others, es-
pecially children, who may inad-
vertently press the button.
OPENING THE TAILGATE
The tailgate can be opened from outside by
remote control pressing button (E), even if the
electronic alarm is on. Opening of the tailgate
is accompanied by the direction indicators
flashing twice; closing is accompanied by a
single flash.
If the electronic alarm is fitted, when the
tailgate is opened the alarm system switch-
es off volumetric protection and the tailgate
control sensor, the system (with the excep-
tion of versions for certain markets) “beeps”
twice.
Closing the tailgate again, the control func-
tions are restored, the system “beeps” twice
(with the exception of certain markets). The metal insert (A) of the key operates:
– the ignition switch
– driver’s door lock and, upon request for
versions/markets where applicable, the pas-
senger’s door lock
– the passenger’s side Air bag deactiva-
tion switch
To bring the metal insert out of the key
grip, press the button (B).
To pull out the hook ring (F) use a finely
pointed object (e.g. pen) and work in the
direction of the arrow.
To insert the metal insert in the key grip:
– keep the button (B) pressed
– move the metal insert (A)
– release the button (B) and turn the met-
al insert (A) until hearing the click as it locks
into place.
To unlock the doors by remote control press
button (C), the doors unlock and the direc-
tion indicators flash twice. To lock the doors
by remote control, press button (D), the
doors lock and the direction indicators flash
once. Pressing button (C) the doors are re-
leased, if within the next 60 seconds a door
or the tailgate are not opened, the system au-
tomatically locks everything again.
On cars fitted with electronic alarm system,
pressing button (C) turns it off, pressing but-
ton (D) turns it on.

GETTING TO KNOW YOUR CAR
11
ELECTRONIC ALARM
DESCRIPTION
The system comprises: a transmitter, re-
ceiver, control unit with siren and volumet-
ric sensors. The electronic alarm is controlled
by the receiver incorporated in the instru-
ment cluster and it is turned on and off by
the remote control in the key which sends
the crypted and variable code. The electronic
alarm controls: the unlawful opening of
doors, bonnet and boot (perimetral protec-
tion), operation of the ignition key, battery
cable cutting, the presence of moving bod-
ies in the passenger compartment (volu-
metric protection), any abnormal rais-
ing/sloping of the car (for versions/mar-
kets where applicable) and central door lock-
ing. It also makes it possible to cut off the
volumetric protection.
IMPORTANTThe engine inhibitor func-
tion is guaranteed by the Alfa Romeo CODE
system which is activated automatically
when the ignition key is removed.The remote control is incorporated in the
key and it is fitted with buttons (B-C-D-
fig. 6) that activate the corresponding con-
trol sending the code to the receiver. This
code (rolling code) changes at each trans-
mission.
REQUEST FOR ADDITIONAL
KEYS WITH
REMOTE CONTROL
The receiver can recognise up to 5 keys
with incorporated remote control. Should a
new key with remote control be necessary
for any reason during the life of the car, con-
tact directly Alfa Romeo Authorised Services,
taking with you the CODE card, a personal
identity document and the car’s ownership
documents.
HOW TO ACTIVATE THE ALARM
With the doors, bonnet and boot shut and
the ignition key in the STOPorPARKpo-
sition (key removed), point the key with the
remote control in the direction of the car, then
press and release the button (C-fig. 6).
With the exception of certain markets, the
system sounds a “beep” and the doors are
locked.
Engagement of the alarm is preceded by
a self-diagnostic test indicated by a different
flashing frequency of the deterrent led (A-
fig. 7) on the dashboard. If a fault is de-
tected the system sounds a further warn-
ing “beep”.
fig. 6
A0A0601b
fig. 7
A0A0005b

GETTING TO KNOW YOUR CAR
12
– if the led continues flashing, but at dif-
ferent intervals than normal, this means that
different attempts to break in have occurred.
Through the number of flashes it is possi-
ble to identify the type of attempt:
1 flash:one or more doors
2 flashes:tailgate
3 flashes:bonnet
4 flashes:ultrasounds
5 flashes:abnormal car lifting/slop-
ing (for versions/markets
where applicable)
6 flashes:tampering with car starting
cables
7 flashes:tampering with battery ca-
bles or cutting emergency
key cables
8 flashes:connection line to sensors
and siren
9 flashes:at least three causes of
alarm. Surveillance
After switching on, the flashing of the de-
terrent led (A-fig. 7) on the dashboard in-
dicates the system surveillance mode. The
led flashes throughout this period.
IMPORTANTOperation of the electronic
alarm is adapted at the origin to the rules
of the different countries.
Self-diagnostic functions
and door, bonnet, boot control
If, after engaging the alarm, a second
“beep” is sounded, switch off the system
pressing the button (B-fig. 6), check that
the doors, bonnet and tailgate are properly
shut, then switch the system on again press-
ing the button (C). Otherwise, the door,
bonnet or tailgate that is not shut properly
will be excluded from the alarm system con-
trol.
If the doors, bonnet and boot are shut cor-
rectly and the control signal is repeated, the
system self-diagnostic has detected a sys-
tem operating fault. It is therefore necessary
to contact Alfa Romeo Authorised Services.HOW TO DEACTIVATE
THE ALARM
To deactivate the alarm press the button (B-
fig. 6) of the key with remote control. The
system will react as follows (with the ex-
ception of certain markets):
– two brief flashes of the direction indi-
cators
– two brief “beeps” of the system
– door unlocking.
IMPORTANTIf when the system is
turned off the deterrent led (A-fig. 7) on
the dashboard stays on (maximum 2 min-
utes or until the ignition key is set to MAR)
the following should be borne in mind:

GETTING TO KNOW YOUR CAR
13
WHEN THE ALARM IS
TRIGGERED
When the system is on, the alarm comes
into action in the following cases:
– opening of one of the doors, bonnet or
tailgate;
– disconnection of the battery or section-
ing of electric cables;
– intrusion in the passenger compartment,
for example breakage of windows (volu-
metric protection);
– attempt to start the engine (key in
MARposition);
– abnormal car lifting/sloping (for ver-
sions/markets where applicable).
Depending on the markets, the cutting in
of the alarm causes operation of the siren
and hazard warning lights (for about 26 sec-
onds). The ways of operating and the num-
ber of cycles may vary depending on the
markets.
A maximum number of cycles is however
envisaged.
Once the alarm cycle has ended, the sys-
tem resumes its normal control function.
VOLUMETRIC PROTECTION
To make sure that the protection system
works correctly the side windows and sun-
roof (if fitted) must be properly shut.
The function can be cut off (if, for exam-
ple, leaving animals in the car) carrying out
the following operations in rapid succession:
starting from the condition with the igni-
tion key at MAR, move the key to STOP,
then immediately back to MARand then
toSTOPagain, then remove the ignition
key.
The deterrent led (A-fig. 7) on the dash-
board lights up for about 2 seconds to con-
firm that the function has been cut off.
To restore volumetric protection, move the
and keep the ignition key at MARfor over
30 seconds.
If, with the volumetric protection function
deactivated, an electric control controlled by
the ignition key at MAR(e.g. power win-
dows) turn the ignition key to MAR, op-
erate the control and move the key to
STOPin a maximum time of 30 seconds.
This way volumetric protection is not re-
stored.
HOW TO CUT OFF
THE ALARM SYSTEM
To deactivate the alarm system complete-
ly (for instance during prolonged inactivity
of the car) simply lock the car turning the
key in the lock.
MINISTERIAL CERTIFICATION
In accordance with the law in force in each
country, on the subject of radio frequency,
we wish to point out that for the markets in
which the transmitter needs to be marked,
the certification number is given on the com-
ponent.
Depending on the versions/markets, the
code may also be given on the transmitter
and/or on the receiver.

GETTING TO KNOW YOUR CAR
105
PARKING SENSORS
(fig. 111)
(upon request for
versions/markets where
applicable)
Parking sensors are located in the rear
bumper and their function is to inform the
driver, through an intermittent buzzer,
about the presence of obstacles behind
the car.
ACTIVATION
Sensors are automatically activated
when the reverse gear is engaged.
As the distance from the obstacle behind
the car decreases, the acoustic alarm
becomes more frequent.
BUZZER WARNINGS
When the reverse gear is engaged an
intermittent acoustic signal is automatical-
ly activated.
The acoustic signal:
– becomes louder as the reduction of
distance between the car and the obstacle
decreases;
– becomes continuous when the dis-
tance between the car and the obstacle is
less that 30 cm and stops immediately if
the distance raises.
– is constant if the distance is unvaried.
If this situation takes place for side sen-
sors, the signal is stopped after about 3
seconds to prevent sound indications
when performing manoeuvres near walls.
OPERATION WITH TRAILER
Parking sensor operation
is deactivated automati-
cally when the trailer elec-
tric cable plug is fitted into the car
tow hook socket.
Sensors are reactivated automatically
when removing the trailer cable plug.
fig. 111
A0A0735b

GETTING TO KNOW YOUR CAR
127
RADIO
TRANSMITTERS
AND CELLULAR
TELEPHONES
Mobile phones and other radio transceiv-
er equipment (e.g.: HAM radio systems and
the like) shall not be used inside the car un-
less a separate aerial is mounted.
IMPORTANTThe use of mobile phones,
HAM radio systems or other similar devices
inside the passenger compartment (without
separate aerial) may cause electronic sys-
tems equipping the car to malfunction. This
could compromise safety in addition to con-
stituting a potential hazard for the passen-
gers.
In addition, transmission and reception of
these devices may be affected by the shield-
ing effect of the car body.
As concerns the use of mobile phones
(GSM, GPRS, UMTS) with homologa-
tion, keep strictly to the mobile phone man-
ufacturer’s specifications.
ACCESSORIES
PURCHASED BY
THE OWNER
If after buying the car, you decide to install
electrical accessories that require a perma-
nent electric supply (alarm, voice feature,
radionavigator with satellite antitheft, etc.)
or accessories that in any case burden the
electric supply, contact Alfa Romeo Autho-
rised Services, whose qualified personnel,
besides suggesting the most suitable devices
belonging to Lineaccessori Alfa Romeo, will
also evaluate the overall electric absorption,
checking whether the car electric system is
able to withstand the load required, or
whether it needs to be integrated with a
more powerful battery.
INSTALLATION OF
ELECTRIC/ELECTRONIC
DEVICES
Electric/electronic devices installed after
buying the car or in aftermarket shall bear
the and marking:
Fiat Auto S.p.A. authorizes the installation
of transceivers provided that installation is
carried out at a specialized shop, work-
manlike performed and in compliance with
manufacturer’s specifications.
IMPORTANTInstallation of devices re-
sulting in modifications of car characteristics
may cause driving license seizing by traffic
agents and also the lapse of the warranty
as concerns defects due to the abovemen-
tioned modification or traceable back to it
directly or indirectly.
Fiat Auto S.p.A. declines all responsibility
for damages caused by the installation of
non-genuine accessories or not recom-
mended by Fiat Auto S.p.A. and installed
not in compliance with the specified re-
quirements.

GETTING TO KNOW YOUR CAR
128
OPENING FROM INSIDE
(fig. 141)
Tailgate is released electrically and this can
be performed only when the ignition key
is in position MARwith car at a standstill
or in STOPorPARKposition for 3 min-
utes without unlocking/locking one of the
doors.
To unlock the tailgate, press button (A)
on the centre console panel.
Tailgate raising is facilitated by the gas
shock springs.
OPENING WITH REMOTE
CONTROL
(fig. 142)
The tailgate can be opened by remote con-
trol from outside pressing the button (A),
also when the electronic alarm is engaged.
Opening of the tailgate is accompanied by
a double flash of the direction indicators;
closing is accompanied by a single flash.
If an electronic alarm is fitted, with the
opening of the tailgate, the alarm system
switches off volumetric protection and the
tailgate control sensor, the system “beeps”
twice (with the exception of certain mar-
kets).
fig. 141
A0A0129b
BOOT
The tailgate can be opened:
from the outside of the car- by a
remote control impulse;
from the inside of the door- by de-
pressing the button (A-fig. 141).
IMPORTANTIf the boot is not proper-
ly shut, the
´warning light will come on
(on certain versions accompanied by the
message on the reconfigurable multifunction
display).
The gas springs are cali-
brated to ensure correct
tailgate raising with the
weights foreseen by the manufac-
turer. The arbitrary addition of
items (such spoilers, etc.) may
compromise the correct operation
and safety of the actual tailgate.
fig. 142
A0A0636b