2010 Alfa Romeo GT audio

GETTING TO KNOW YOUR CAR
153
Each band is shown by the respective
wording on the display.
The last station selected in the respective
frequency band will be tuned.
The FM band is divided into sections: FM1,
FM2 and FMT. The FMT reception band is
reserved to the stations stored automatically
with the Autostore function.
Presetting buttons
The buttons with symbols from 1 to 6
make it possible to set the following pre-
settings:
– 18 in the FM band (6 in FM1, 6 in
FM2, 6 in FMT);
– 6 in the MW band;
– 6 in the LW band;
To call a preset station, choose the required
frequency band and then press briefly the
corresponding preset button (from 1 to 6).
Pressing the respective preset button for
longer than 2 seconds will store the tuned
station. Storing is confirmed by a beep. Storing the last station heard
The radio automatically keeps in storage
the last station heard for each reception
band, which is then tuned when the radio is
turned on or the reception band is changed.
Automatic tuning
Briefly press button
÷or˜to start
automatically searching the tuning for the
next station that it is possible to receive in
the direction chosen.
If button
÷or˜is pressed for
longer, quick searching takes place. When
the button is released, the tuner stops on
the next receivable station.
If the TA function is on (traffic information),
the tuner only searches stations which broad-
cast traffic bulletins.
RADIO (TUNER)
Introduction
When the set is turned on the last function
selected before turning off is played (Radio,
CD or CD Changer).
To select the Tuner source while listening
to another audio source, press briefly but-
tons FM
ASor AM, according to the required
frequency band.
When Tuner is on, the display will show
the selected station name (RDS stations on-
ly) (or frequency), the frequency band (e.g.:
FM1) and the preselection button number
(e.g.: P1).
Selecting the frequency band
If in the Tuner mode, briefly and repeat-
edly press button FM
ASor AM to select the
required frequency band.
Every time the button is pressed the fol-
lowing bands are selected in sequence:
– Pressing button FM
AS: “FM1”, “FM2”,
“FMT”;
– Pressing button AM: “MW” and “LW”.

GETTING TO KNOW YOUR CAR
155
EON function
(Enhanced Other Network)
Certain countries have circuits which group
together several stations enabled to broad-
cast traffic information. In this case the pro-
gramme of the station being heard will be
interrupted temporarily:
– to receive traffic information (only with
TA function on);
– to listen to regional programmes every
time these bulletins are given by one of the
stations of the same circuits.
Stereophonic stations
If the signal received is weak, the device
switches automatically from Stereo to Mono. MENU
MENU button functions
To activate the menu function, briefly press
button MENU. The display shows the word
“MENU”.
To scroll the menu functions use button
▲
or▼. To change the setting of the select-
ed function use button
÷or˜.
The display will show the current status
of the function selected.
The functions controlled by the menu are
the following:
– AF (alternative frequency search);
– TA (traffic information);
– REG (regional programmes);
– MP3 DISP (MP3 CD data display);
– SVC (automatic volume control in rela-
tion to speed);
– EXT VOL (external audio sources con-
trol);
– IGN TIME (System power off mode ra-
dio);
– DEFAULT (reset original settings).
To exit the menu function, press button
MENU again. Emergency alarm reception
In the RDS mode the radio is set to receive
emergency announcements in the case of
exceptional circumstances or events that
may cause general danger (earthquakes,
floods, etc.), if they are broadcast by the
station tuned.
This function is activated automatically and
cannot be deactivated.
During emergency announcement the dis-
play will show the message “ALARM”. Dur-
ing this announcement the volume will
change as described for traffic announce-
ments (see “TA Function”).

GETTING TO KNOW YOUR CAR
158
EXT function
(external audio source control)
With this function it is possible to adjust
(setting from 0 to 40) or exclude (OFF) ex-
ternal audio sources.
To turn this function on/off, use button
÷or˜.
The display will show the current status
of the function:
– “EXT VOL”: function on.
– “EXT OFF”: function off.
– “EXT 23”: function on with volume lev-
el 23.
IGN TIME function
(system power on/off mode radio)
This function enables to switch off the
sound system according to two different
modes. To turn the function on use button
÷or˜.
The display will show “IGN TIME” and then:
– “00 MIN”: deactivation dependent on
ignition key. Sound system will switch off
automatically when turning the ignition key
to STOP;
– “20 MIN”: deactivation independent of
ignition key. After having turned the ignition
key to STOP the sound system will stay on
for 20 minutes max.IMPORTANTWhen the sound system
is switched off automatically after turning
the ignition key to STOP (for both immedi-
ate or 20-minute delayed power off), it will
switch on automatically turning the ignition
key to MAR. If the sound system has been
switched off pressing button ON, when turn-
ing the key to MAR it will stay off.
RESTORE function
This function enables to restore default set-
tings. Options available are the following:
– NO: no restore;
– YES: restore default settings. During this
operation the display will show the message
“RESTORE”. At the end of this operation,
the audio source will not be changed and
the previous situation is displayed. SVC function
(volume changing with speed)
(excluding versions with
Bose HI-FI system)
This function makes it possible to auto-
matically adapt the volume level to the
speed of the car, increasing it as the speed
increases to maintain the ratio with the noise
level inside the passenger compartment.
To turn the function on/off use button
÷or˜. The display will show the cur-
rent status of the function:
– SVC OFF: function off
– SVC LOW: function on
(low sensitivity)
– SVC HIGH: function on
(high sensitivity).

GETTING TO KNOW YOUR CAR
162
Technical data and operating conditions for
MP3 files are as follows:
– adopted CD-ROM shall be mastered ac-
cording to ISO9660 Standard;
– music files shall be renamed as “.mp3”
otherwise they cannot be played;
– sampling frequencies are: 44.1 kHz,
stereo (96 to 320 kbit/s) - 22.05 kHz,
mono or stereo (32 to 80 kbit/s);
– it is possible to play variable bit-rate
tracks (files).
IMPORTANTCharacters: blank, ‘ (apos-
trophe), ( and ) (open and closed brackets)
are not admitted in MP3 track names. When
sampling MP3 CD you must not use these
characters to name files otherwise the sound
system will not be able to play it. DISPLAY INFORMATION
ID3-tag info display
(track informations)
In addition to time elapsed, directory name
and file name, also ID3-tag info relevant to
track Title, Artist, Author (see section “MP3
disp function”) are displayed.
The MP3 directory name shown on the dis-
play corresponds to the name with which
the directory is stored on the CD, followed
by an asterisk.
Example of full MP3 directory name: BEST
OF *.
If you want to display one ID3-tag info (Ti-
tle, Artist, Album) and the track being played
has no ID3-tag info then, the file name will
be displayed.
MP3 CD PLAYER
(where provided)
Introduction
This section only describes MP3 CD play-
er operation variants: as concerns sound sys-
tem operation, refer to “Functions and Ad-
justments” paragraph.
NOTEMPEG Layer-3 audio decoding tech-
nology licensed from Fraunhofer IIS and
Thomson multimedia.
MP3 mode
In addition to standard audio CDs, the sound
system can also play audio files in MP3 for-
mat. Sound system will operate as described
in “Compact Disc player” paragraph when in-
serting a conventional audio CD.
For optimal playing use only top quality
CDs mastered at a speed as low as possible.
MP3 CD files are structured by directories,
with sequential lists of all directories con-
taining MP3 tracks (directories and sub-di-
rectories are all brought to the same lev-
el), directories not containing MP3 tracks
cannot be selected.