2010 Alfa Romeo GT ECU

IN AN EMERGENCY
199
REVERSING LIGHT
AND REAR FOG GUARDS
(fig. 31-32)
The reverse light and the rear fog light
(both reverse lights for Mexico version) are
housed inside the light unit secured to the
rear bumper and are located at the bottom
side.
fig. 31
A0A0627b
fig. 33
A0A0629b
To change the bulb, proceed as follows:
– from the bumper lower side (fig. 31),
operate on the bulb holder (A-fig 32) turn-
ing it counter-clockwise and remove it. Take
care not to get burnt if the muffler is still hot;
– Remove the bulb pushing gently and
turning counter-clockwise;
– Replace the bulb, then refit the bulb
holder.
Anyway, you are advised to have this op-
eration carried out by Alfa Romeo Authorised
Services.REAR DIRECTION INDICATORS
AND REAR SIDELIGHTS-
BRAKING LIGHTS
(fig. 33-34)
The rear direction indicators and the side-
lights-braking lights are in the tail light unit
fastened to the body.
To change the bulb, proceed as follows:
– From inside the boot, open the com-
partment (A-fig. 33) and then the door
(B) through the tab (C);
– Turn the bulb for sidelight and braking
light counter-clockwise (D-fig.34), or the
bulb for the direction indicator (E-fig.34)
and remove it;
fig. 32
A0A0628b

IN AN EMERGENCY
200
NUMBER PLATE LIGHTS
(fig. 35)
To change the bulbs, proceed as follows:
– Work on the transparent cover frame,
in the point shown by the arrow to compress
the catch (B). Free the opposite end and re-
move the unit.
– Turn the bulb holder counter-clockwise (A)
and remove it from the transparent cover.
– Remove the snap-fitted bulb and replace it.
– Insert the bulb holder (A) in the trans-
parent cover then refit the unit checking that
the catch clicks into place (B).
ADDITIONAL BRAKING LIGHT
(THIRD STOP)
(fig. 36-37)
To change the led unit, proceed as follows:
– Open the tailgate and use a screwdriv-
er to open the two covers (A-fig. 36);
– Slacken the two fastening screws of (B)
the led unit;
fig. 35
A0A0171b
fig. 36
A0A0631b
A0A0630b
– Withdraw the light (ForG) push it gen-
tly and turn counter-clockwise;
– Replace the bulb;
– Refit the bulb holder turning clockwise
and make sure it is secured correctly;
– Refit the door (B) and close the com-
partment (A).
fig. 34

TECHNICAL SPECIFICATIONS
240
IDENTIFICATION LABEL
This (fig. 2) is to be found on the front
crossmember of the engine compartment.
It contains the following information:
(A)Space for details of national ho-
mologation
(B)Space for punching the consecutive
chassis number
(C)Space available for maximum
weights authorised by various na-
tional regulations
(D)Space for version and any supple-
mentary indications to those specified(E)Space for smoke coefficient (JTD ver-
sions)
(F)Space for punching manufacturer’s
name.
BODYWORK LABEL
This is located in the engine bay, to one
side of the upper right shock absorber (fig.
3) and contains:
– Type of vehicle: ZAR 937.000
– Manufacturer’s serial number (chassis
number).
IDENTIFICATION DATA
You are advised to note the identification
codes. The identification datastamped and
given on the labels and their position are
the following (fig. 1):
1- Identification label
2- Body label
3- Bodywork paint identification label
4- Engine label.
T T
E E
C C
H H
N N
I I
C C
A A
L L
S S
P P
E E
C C
I I
F F
I I
C C
A A
T T
I I
O O
N N
S S
fig. 1
A0A0654b
fig. 2
A0A0246b
fig. 3
A0A0247b