2010 Acura TSX headlight bulb

Theheadlightswereproperlyaimed
when your vehicle was new. If you
regularly carry heavy items in the
trunk or pull a trailer, readjustment
may be required. Adjustments
should be done by your dealer or
another qualif ied technician.The low beam headlight bulbs are
high voltage discharge tube bulbs.
High voltage can remain in the
circuit even with the light switch of f
and the key removed. Because of
this, you should not attempt to
examine or change a low beam
headlight bulb yourself . If a low
beam headlight bulb fails, take the
vehicle to your dealer to have it
replaced.Your vehicle has halogen headlight
bulbs. When replacing a bulb, handle
it by its base, and protect the glass
f rom contact with your skin or hard
objects. If you touch the glass, clean
it with denatured alcohol and a clean
cloth.
CONT INUED
High beam headlights on all models
Low beam headlights on Canadian TSXwith 4-cylinder engine
All models except Canadian TSX with
4-cylinder engine
Headlight Aiming L ow Beam Headlight Bulb
ReplacementReplacing a Headlight Bulb
Lights
Maint enance
429
Halogen headlight bulbs get very hot
when lit. Oil, perspiration, or a scratch
on the glass can cause the bulb to
overheat and shatter.
2010 TSX

To change the passenger’s side
bulb, start the engine, turn the
steering wheel all the way to the
lef t, and turn of f the engine. To
change the driver’s side bulb, turn
the steering wheel to the right.Pull the inner f ender cover away
f rom the f ender and bumper.
Remove the cover on the back of
the headlight assembly by turning
the tab counterclockwise.
Use a f lat-tip screwdriver to
remove the holding clip f rom the
inner f ender, and remove the
screw with a Phillips-head
screwdriver.
3.
4.
1.
2.
Canadian TSX with 4-cylinder engine
L ow Beam Headlight
Lights
430
TAB
COVER
SCREW HOLDING CLIP
2010 TSX

Open the hood.
Insert the new bulb into the hole,
making sure the tabs are in their
slots.
Push the electrical connector onto
the new bulb. Make sure it is
connected securely.
Pivot the hold-down wire back in
place, and clip the end into the slot.
Reinstall the cover over the back
of the headlight assembly and turn
it clockwise to lock it in place.
Turn on the headlights to test the
new bulb.
Put the inner f ender cover in place.
Install the holding clip. Lock it in
placebypushingonthecenter.
Tighten the screw securely.
Remove the electrical connector
f rom the bulb by pulling the
connector straight back, then
remove the bulb. Unclip the end of the hold-down
wire f rom its slot. Pivot it out of
the way.
Tochangeabulbonthe
passenger’s side, remove the
engine coolant reserve tank by
pulling it out of its stay. Remove all engine compartment
covers (see page ).
1.
8. 7.
9.
10.
11.
12.
5.
6.
2.
3.414
CONT INUED
6-cylinder models
High Beam Headlights
Lights
Maint enance
431
STAY
4-cylinder models
2010 TSX

Install the new bulb, and turn it
one-quarter turn clockwise to lock
it in place.
Push the electrical connector back
onto the bulb. Make sure it is on
all the way.
Turn on the headlights to test the
new bulb.
Reinstall the coolant reserve tank.
Remove the electrical connector
f rom the bulb by pushing on the
tab to unlock it, then slide the
connector of f the bulb. Remove the bulb by turning it
approximately one-quarter turn
counterclockwise.
Reinstall the air intake duct cover,
then reinstall the f asteners. Reinstall the cover and upper part
of the air intake duct securely.
Reinstall the f asteners.
4.
5. 6.
7.
8.
9.
On the passenger’s side
On the driver’s side4-cylinder models:
6-cylinder models:
Lights
Maint enance
433
4-cylinder models 6-cylinder models
2010 TSX

Remove the socket from the
headlight assembly by turning it
one-quarter turn counterclockwise.
To remove the burned out bulb,
push it in and turn it
counterclockwise until it unlocks.
Use a f lat-tip screwdriver to
remove the holding clip f rom the
inner f ender, and remove the
screw with a Phillips-head
screwdriver.
Pull the inner f ender cover away
f rom the f ender and bumper.
To change the bulb on the driver’s
side, start the engine, turn the
steering wheel all the way to the
right, then turn of f the engine. To
change the bulb on the passenger’s
side, turn the steering wheel to the
lef t.
4.
5.
2.
1.
3.
Lights
Replacing a Front T urn Signal/
Parking and Side Marker Light
Bulb
434
SCREWHOLDING CLIP
2010 TSX

Turn on the lights to make sure
the new bulb is working. Insert the socket back into the
headlight assembly. Turn it
clockwise to lock it in place. Install the new bulb and turn it
clockwise to lock it in place.
Put the inner f ender cover in place.
Install the holding clip. Lock it in
placebypushingonthecenter.
Tighten the screw securely.Open the trunk.
Remove the light assembly cover
by pulling its outside edge.Remove the socket by turning it
one-quarter turn counterclockwise,
and pull the bulb straight out of its
socket. Determine which of the three
bulbs is burned out: stop/taillight,
rear side-marker, or turn signal
light.
9. 7.
8. 6.
1.
2.3.
4.
Lights
Replacing Rear Bulbs
(In Fenders)
Maint enance
435
COVER
2010 TSX

ÎÎ
Î
µ
µ
µ
µ
µ
µ
µ
µ
µ
µ
µ
µ
µ
µ
µ
µ
Î
Î
Î
µ
µ
µ
CONT INUED
Specif ications (4-cylinder Models)
Technical Inf ormation
489
Battery
Lights
Engine Fuses 12V 36AH/5HR
60W
12 V
12 V 35 W
Capacity
12 V 2 W 12 V 3.8 W
12 V 5 W12 V 8 W
12 V 8 W
12 V 5 W 12 V 3 CP
12 V 21 W
12 V 21 W
12 V 21/5 W
12 V 21 W 12 V 12 V 55 W 55 W
On vehicles with high voltage discharge type headlights,
replacement of a headlight bulb should be done by your dealer. 12 V
12 V 45 AH/20 HR
21/5 W
Headlights
Fog lights
Front turn signal/
Front parking lights/
Side marker lights
Rear turn signal lights
Stop/Taillights
High-mount brake light
Back-up lights
Rear side marker lights
License plate lights
Ceiling light
Spotlights
Trunk light
Door courtesy lights
Vanity mirror lights
SXU22HCR11S ILZKR7B-11S 11.0 : 1
144 cu-in (2,354 cm
)
3.43 x 3.90 in (87.0 x 99.0 mm) Water cooled 4-stroke, DOHC
i-VTEC 4-cylinder, gasoline engine
Type
BorexStroke
Displacement
Compression ratio
Spark plugs Interior
Under-hood 12 V 47 AH/20 HR
See page 480or the fuse label
attached on the side panel.
See page 481or the fuse label
attached to the inside of the fuse
box door.
See page 479or the fuse box
cover.
NGK:
DENSO:
Driver’s side
Passenger’s side
High
Low
(D2S)
(H1)
(H11)
Canadian TSX (HB3)
1:
2:
3 : If equipped
3 1
2
2010 TSX

µ
µÎ µ
µ
µ
µ
µ
µ
µ
µ
µ
µ
µ
µ
µ
µ
µÎ
Specif ications (6-cylinder Models)
492
Battery
Engine Fuses
Lights
Capacity 12 V
12 V 55 AH/5 HR
72 AH/20 HR
3.50 x 3.66 in (89.0 x 93.0 mm) 212 cu-in (3,471 cm
)
11.2 : 1
ILZKR7B11
SXU22HCR11 12 V 60 W
12 V 35 W
Type
BorexStroke
Displacement
Compression ratio
Spark plugs Interior
Under-hood See page
480or the fuse label
attached on the side panel.
See page 481or the fuse label
attached to the inside of the fuse
box door.
See page 479or the fuse box
cover.
On vehicles with high voltage discharge type headlights,
replacement of a headlight bulb should be done by your dealer.
Headlights
Fog lights
Front turn signal/
Front parking lights/
Side marker lights
Rear turn signal lights
Stop/Taillights
High-mount brake light
Back-up lights
Rear side marker lights
License plate lights
Ceiling light
Spotlights
Trunk light
Door courtesy lights
Vanity mirror lights
12 V
12 V
12 V
12 V
12 V
12 V
12 V
12 V
12 V 12 V
12 V
12 V
12 V 55 W
21/5 W
21 W
21/5 W
21 W
21 W
3CP
5W
8W
8W
5W
3.8 W
2W
Water cooled 4-stroke,
SOHC VTEC 6-cylinder (V6), gasoline engine
NGK:
DENSO:
Driver’s side
Passenger’s side
High
Low
(D2S)
(H11) (HB3)
:
2010 TSX