2010 Acura TSX brake

Place the jack under the jacking
point nearest the tire you need to
change. Turn the end bracket
clockwise until the top of the jack
contacts the jacking point. Make
sure the jacking point tab is
restinginthejacknotch.Use the extension and the wheel
nut wrench as shown to raise the
vehicle until the f lat tire is of f the
ground.
Remove the wheel nuts, then
removetheflattire.Handlethe
wheel nuts caref ully; they may be
hot from driving. Place the flat tire
on the ground with the outside
surface facing up.Bef ore mounting the spare tire,
wipeanydirtoff themounting
surface of the wheel and hub with
a clean cloth. Wipe the hub
carefully;itmaybehotfrom
driving.
8.
9.
10. 11.
CONT INUED
Changing a Flat Tire
T aking Care of t he Unexpect ed
461
JACKING POINT
WHEEL NUT WRENCHEXTENSION
BRAKE HUB
2010 TSX

Although this seems like a simple
procedure, you should take several
precautions.Open the hood, and check the
physical condition of the battery.
In very cold weather, check the
condition of the electrolyte. If it
seems slushy or f rozen, do not try
jump starting until it thaws.
To jump start your vehicle:
You cannot start your vehicle with an
automatic transmission by pushing
or pulling it. Turn of f all the electrical
accessories: climate control, audio
system, lights, etc. Put the
transmission in neutral (manual)
or Park (automatic), and set the
parking brake.Slide out the battery terminal
cover. The battery terminal cover
can be removed without removing
theleftsideenginecompartment
cover.
1.
2.
3.
6-cylinder models
Jump Starting
466
COVER
A battery can explode if you do
not follow the correct procedure,
seriously injuring anyone
nearby.
Keep all sparks, open flames,
and smoking materials away
from the battery.
If a battery sits in extreme cold, the
electrolyte inside can f reeze.
Attempting to jump start with a f rozen
battery can cause it to rupture.
2010 TSX

If the temperature gauge stays at
the red mark, turn of f the engine.
Look f or any obvious coolant leaks,
such as a split radiator hose.
Everything is still extremely hot,
so use caution. If you f ind a leak, it
must be repaired bef ore you
continue driving (seeon page ).
If you do not see steam or spray,
leave the engine running and
watch the temperature gauge. If
the high heat is due to overloading,
the engine should start to cool
down almost immediately. If it
does, wait until the temperature
gauge comes down to the midpoint,
then continue driving.
The pointer of the vehicle’s
temperature gauge should stay in
the midrange. If it climbs to the red
mark, you should determine the
reason (hot day, driving up a steep
hill, etc.).
You will also see a ‘‘WATER TEMP
HOT’’ message on the multi-
inf ormation display (see page ).
If your vehicle overheats, you should
take immediate action. The only
indicationmaybethetemperature
gauge climbing to or above the red
mark. Or you may see steam or
spray coming f rom under the hood.
Saf ely pull to the side of the road.
Put the transmission in neutral
(manual) or Park (automatic), and
set the parking brake. Turn of f all
accessories, and turn on the
hazard warning lights.
If you see steam and/or spray
coming f rom under the hood, turn
of f the engine. Wait until you see
no more signs of steam or spray,
then open the hood.
1.
2. 3.
4.
5.
69
482
CONT INUED
Emergency
Towing
If theEngineOverheats
T aking Care of t he Unexpect ed
469
Steam and spray from an
overheated engine can
seriously scald you.
Do not open the hood if steam
is coming out.
Driving with the temperature gauge
pointer at the red mark can cause
serious damage to the engine.
2010 TSX

If you must drive the vehicle a short
distance in this condition, drive
slowly and caref ully. Slow down by shif ting to a lower
gear, and pull to the side of the road
when it is saf e. Because of the long
distance needed to stop, it is
hazardous to drive the vehicle. You
should have it towed and repaired as
soon as possible (seeon page ).
If the ABS indicator and the VSA
system indicator come on with the
brake system indicator, have your
vehicle inspected by your dealer
immediately.
The brake system indicator normally
comes on when you turn the ignition
switch to the ON (II) position, and as
a reminder to check the parking
brake. It will stay on if you do not
f ully release the parking brake.
If the brake system indicator comes
on while driving, the brake f luid level
is probably low. Press lightly on the
brake pedal to see if it f eels normal.
If it does, check the brake f luid level
thenexttimeyoustopataservice
station (see page ). If the f luid level is low, take your
vehicle to a dealer, and have the
brake system inspected f or leaks or
worn brake pads.
However, if the brake pedal does not
f eel normal, you should take
immediate action. A problem in one
part of the system’s dual circuit
design will still give you braking at
two wheels. You will f eel the brake
pedal go down much f arther bef ore
the vehicle begins to slow down, and
you will have to press harder on the
pedal.
You will also see a ‘‘CHECK BRAKE
SYSTEM’’ message on the multi-
inf ormation display when this
indicator comes on.
You will also see a ‘‘BRAKE FLUID
LOW’’ message on the multi-
inf ormation display. 427 482
Emergency
Towing
Brake System Indicator
T aking Care of t he Unexpect ed
473
U.S. Canada
2010 TSX

µµ
If your vehicle needs to be towed,
call a prof essional towing service or
organization. Never tow your vehicle
with just a rope or chain. It is very
dangerous.
The operator
loads your vehicle on the back of a
truck. Therearetwowaystotowyour
vehicle: If , due to damage, your vehicle must
be towed with the f ront wheels on
the ground, do this:
With the f ront wheels on the ground,
it is best to tow the vehicle no farther
than 50 miles (80 km), and keep the
speedbelow35mph(55km/h).
The tow
truck uses two pivoting arms that go
under the f ront tires and lif t them of f
the ground. The rear tires remain on
the ground. Start the engine.
Release the parking brake. Shif t to D position and hold f or 5
seconds, then to N.
Turn of f the engine.
Leave the ignition switch in the
ACCESSORY (I) position so the
steering wheel does not lock. Shif t the transmission to neutral.
Leave the ignition switch in the
ACCESSORY (I) position so the
steering wheel does not lock.
Release the parking brake.
Manual transmission:
Automatic transmission:
Flat -bed Equipment
Wheel-lif t Equipment
T his is the best way to
transport your vehicle.
This is an acceptable
way to tow your vehicle.
Emergency Towing
482
Improper towing preparation will
damage the transmission. Follow the
above procedure exactly. If you cannot
shif t the transmission or start the
engine (automatic transmission), your
vehicle must be transported with the
f ront wheels of f the ground.
2010 TSX

ÎÎ
Î
µ
µ
µ
µ
µ
µ
µ
µ
µ
µ
µ
µ
µ
µ
µ
µ
Î
Î
Î
µ
µ
µ
CONT INUED
Specif ications (4-cylinder Models)
Technical Inf ormation
489
Battery
Lights
Engine Fuses 12V 36AH/5HR
60W
12 V
12 V 35 W
Capacity
12 V 2 W 12 V 3.8 W
12 V 5 W12 V 8 W
12 V 8 W
12 V 5 W 12 V 3 CP
12 V 21 W
12 V 21 W
12 V 21/5 W
12 V 21 W 12 V 12 V 55 W 55 W
On vehicles with high voltage discharge type headlights,
replacement of a headlight bulb should be done by your dealer. 12 V
12 V 45 AH/20 HR
21/5 W
Headlights
Fog lights
Front turn signal/
Front parking lights/
Side marker lights
Rear turn signal lights
Stop/Taillights
High-mount brake light
Back-up lights
Rear side marker lights
License plate lights
Ceiling light
Spotlights
Trunk light
Door courtesy lights
Vanity mirror lights
SXU22HCR11S ILZKR7B-11S 11.0 : 1
144 cu-in (2,354 cm
)
3.43 x 3.90 in (87.0 x 99.0 mm) Water cooled 4-stroke, DOHC
i-VTEC 4-cylinder, gasoline engine
Type
BorexStroke
Displacement
Compression ratio
Spark plugs Interior
Under-hood 12 V 47 AH/20 HR
See page 480or the fuse label
attached on the side panel.
See page 481or the fuse label
attached to the inside of the fuse
box door.
See page 479or the fuse box
cover.
NGK:
DENSO:
Driver’s side
Passenger’s side
High
Low
(D2S)
(H1)
(H11)
Canadian TSX (HB3)
1:
2:
3 : If equipped
3 1
2
2010 TSX

µ
µÎ µ
µ
µ
µ
µ
µ
µ
µ
µ
µ
µ
µ
µ
µ
µÎ
Specif ications (6-cylinder Models)
492
Battery
Engine Fuses
Lights
Capacity 12 V
12 V 55 AH/5 HR
72 AH/20 HR
3.50 x 3.66 in (89.0 x 93.0 mm) 212 cu-in (3,471 cm
)
11.2 : 1
ILZKR7B11
SXU22HCR11 12 V 60 W
12 V 35 W
Type
BorexStroke
Displacement
Compression ratio
Spark plugs Interior
Under-hood See page
480or the fuse label
attached on the side panel.
See page 481or the fuse label
attached to the inside of the fuse
box door.
See page 479or the fuse box
cover.
On vehicles with high voltage discharge type headlights,
replacement of a headlight bulb should be done by your dealer.
Headlights
Fog lights
Front turn signal/
Front parking lights/
Side marker lights
Rear turn signal lights
Stop/Taillights
High-mount brake light
Back-up lights
Rear side marker lights
License plate lights
Ceiling light
Spotlights
Trunk light
Door courtesy lights
Vanity mirror lights
12 V
12 V
12 V
12 V
12 V
12 V
12 V
12 V
12 V 12 V
12 V
12 V
12 V 55 W
21/5 W
21 W
21/5 W
21 W
21 W
3CP
5W
8W
8W
5W
3.8 W
2W
Water cooled 4-stroke,
SOHC VTEC 6-cylinder (V6), gasoline engine
NGK:
DENSO:
Driver’s side
Passenger’s side
High
Low
(D2S)
(H11) (HB3)
:
2010 TSX

Then drive in city/suburban
traffic for at least 10 minutes.
When traf f ic conditions allow, let
the vehicle coast f or several
seconds without using the
accelerator pedal or the brake
pedal.
If the testing f acility determines the
readiness codes are still not set, see
your dealer. Make sure the vehicle has been
parked with the engine of f f or 30
minutes.
Select a nearby lightly traveled
major highway where you can
maintain a speed of 50 to 60 mph
(80to97km/h)foratleast20
minutes. Drive on the highway in
D (automatic) or 5th (manual). Do
notusethecruisecontrol.When
traffic allows, drive for 90 seconds
without moving the accelerator
pedal. (Vehicle speed may vary
slightly; this is okay.) If you cannot
do this f or a continuous 90
seconds because of traf f ic
conditions, drive f or at least 30
seconds, then repeat it two more
times (for a total of 90 seconds).
7.
8.
9.
Emissions T esting
504
2010 TSX