2010 Acura TSX Anc

Open the hood.
Insert the new bulb into the hole,
making sure the tabs are in their
slots.
Push the electrical connector onto
the new bulb. Make sure it is
connected securely.
Pivot the hold-down wire back in
place, and clip the end into the slot.
Reinstall the cover over the back
of the headlight assembly and turn
it clockwise to lock it in place.
Turn on the headlights to test the
new bulb.
Put the inner f ender cover in place.
Install the holding clip. Lock it in
placebypushingonthecenter.
Tighten the screw securely.
Remove the electrical connector
f rom the bulb by pulling the
connector straight back, then
remove the bulb. Unclip the end of the hold-down
wire f rom its slot. Pivot it out of
the way.
Tochangeabulbonthe
passenger’s side, remove the
engine coolant reserve tank by
pulling it out of its stay. Remove all engine compartment
covers (see page ).
1.
8. 7.
9.
10.
11.
12.
5.
6.
2.
3.414
CONT INUED
6-cylinder models
High Beam Headlights
Lights
Maint enance
431
STAY
4-cylinder models
2010 TSX

Install the new bulb, and turn it
one-quarter turn clockwise to lock
it in place.
Push the electrical connector back
onto the bulb. Make sure it is on
all the way.
Turn on the headlights to test the
new bulb.
Reinstall the coolant reserve tank.
Remove the electrical connector
f rom the bulb by pushing on the
tab to unlock it, then slide the
connector of f the bulb. Remove the bulb by turning it
approximately one-quarter turn
counterclockwise.
Reinstall the air intake duct cover,
then reinstall the f asteners. Reinstall the cover and upper part
of the air intake duct securely.
Reinstall the f asteners.
4.
5. 6.
7.
8.
9.
On the passenger’s side
On the driver’s side4-cylinder models:
6-cylinder models:
Lights
Maint enance
433
4-cylinder models 6-cylinder models
2010 TSX

Turn on the lights to make sure
the new bulb is working. Insert the socket back into the
headlight assembly. Turn it
clockwise to lock it in place. Install the new bulb and turn it
clockwise to lock it in place.
Put the inner f ender cover in place.
Install the holding clip. Lock it in
placebypushingonthecenter.
Tighten the screw securely.Open the trunk.
Remove the light assembly cover
by pulling its outside edge.Remove the socket by turning it
one-quarter turn counterclockwise,
and pull the bulb straight out of its
socket. Determine which of the three
bulbs is burned out: stop/taillight,
rear side-marker, or turn signal
light.
9. 7.
8. 6.
1.
2.3.
4.
Lights
Replacing Rear Bulbs
(In Fenders)
Maint enance
435
COVER
2010 TSX

Remove the socket by turning it
one-quarter turn counterclockwise.
Pull the bulb straight out of its
socket. Push the new bulb straight
into the socket until it bottoms.Turn on the lights to make sure
the new bulb is working.
Reinstall the trunk lid lining. Make
sure it is installed under the edge
of the trunk seal. Insert the socket back into the
light assembly. Turn it clockwise
to lock it in place.
Install the f asteners.
Each outside mirror has side turn
signal lights. The lights should be
replaced by your dealer.
The license plate has two lights
above it. The bulbs should be
replaced by your dealer.
4.
5. 6.
7.
8.
9.
Lights
Side T urn Signal L ights
Rear License Plate Light Bulbs
Maint enance
437
SOCKET
2010 TSX

Remove the three holding clips
with a flat-tip screwdriver.
Pull down the under cover f rom
the bumper caref ully.
Your vehicle uses halogen light
bulbs. When replacing a bulb, handle
it by its plastic case, and protect the
glass from contact with your skin or
hard objects. If you touch the glass,
clean it with denatured alcohol and a
clean cloth.
Thefoglightswereproperlyaimed
when your vehicle was new. If you
regularly carry heavy items in the
trunk or pull a trailer, readjustment
may be required. Adjustment should
be done by your dealer or another
qualif ied technician.
1.
2.
If equipped
CONT INUED
ReplacingaFogLightBulb
Lights
Maint enance
439
HOLDING CLIPS
UNDER COVER
Halogen bulbs get very hot when lit. Oil,
perspiration, or a scratch on the glass
can cause the bulb to overheat and
shatter.
2010 TSX

If your seat belts get dirty, use a sof t
brush with a mixture of mild soap
and warm water to clean them. Do
not use bleach, dye, or cleaning
solvents. Let the belts air dry bef ore
you use the vehicle.Dirt build-up around the openings of
the seat belt anchors can cause the
belts to retract slowly. Wipe the
openings with a clean cloth
dampened in mild soap and warm
water or isopropyl alcohol.
When cleaning or replacing, turn the
knob counterclockwise to unhook
the floor mat. The driver’s f loor mat that came
with your vehicle hooks over the
f loor mat anchors. To lock each
anchor, turn the knob clockwise.
This keeps the f loor mat f rom sliding
f orward and possibly interf ering with
the pedals.
CONT INUED
Floor Mats
Cleaning the Seat Belts
Cleaning the Seat Belts, Floor Mats
Maint enance
441
Driver’s floor mat is shown.
OPENING
To unlock
2010 TSX

If you remove a f loor mat, make sure
tore-anchoritwhenyouputitback
in your vehicle.
If you use a non-Acura f loor mat,
make sure it f its properly and that it
canbeusedwiththefloormat
anchors. Do not put additional f loor
mats on top of the anchored mats.This f ilter removes the dust and
pollenthatisbroughtinfromthe
outside through the climate control
system.
Have your dealer replace the filter
when this service is indicated by a
maintenance message on the multi-
inf ormation display. It should be
replaced every 15,000 miles (24,000
km) if you drive primarily in urban
areas that have high concentrations
of soot in the air, or if the f low f rom
theclimatecontrolsystembecomes
less than usual.
Make sure the rear f loor mats are
properly positioned. If not, the f loor
mat will interf ere with the seat
operation and make the f ront
passenger’s weight sensors
inef f ective. Dust and Pollen Filter
Exterior Care
Floor Mats, Dust and Pollen Filter, Exterior Care
442
Chemical solvents and strong cleaners
can damage the paint, metal, and
plastic on your vehicle.
2010 TSX

To replace a wiper blade:Disconnect the blade assembly
from the wiper arm:
Raise each wiper arm of f the
windshield, lif ting the driver’s side
first, then the passenger’s side.
Check the condition of the wiper
blades at least every six months.
Replace them if you f ind signs of
cracking in the rubber, areas that are
getting hard, or if they leave streaks
and unwiped areas when used.
Put a cloth on the edge of the
lock tab to prevent scratches,
then push up on the lock tab
carefully with a flat-tip
screwdriver.
2.
1.
CONT INUED
Wiper Blades
Maint enance
443
WIPER BLADES
LOCK TAB
Do not open the hood when the wiper
arms are raised, or you will damage the
hood and wiper arms.
2010 TSX