2010 Acura TL engine

This shows the temperature of the
engine’s coolant. During normal
operation, the pointer should rise
from the bottom mark to about the
middle of the gauge. In severe
driving conditions, such as very hot
weather or a long period of uphill
driving, the pointer may rise to the
upper zone. If it reaches the red
(hot) mark, pull saf ely to the side of
the road. Turn to page for
instructions and precautions on
checking the engine cooling system. If the pointer of the temperaturegauge reaches to or above the red
mark, you will also see the ‘‘WATER
TEMP HOT’’ message on the multi-
inf ormation display. This will alert
you that the engine should be cooled
down.
557
Temperature Gauge
Gauges
76
09/07/29 16:55:17 31TK4610_081
2010 TL

Î
Î
CONT INUED
You can select the displayed
language and also customize some
vehicle control settings to your liking
with the multi-information display
and the three buttons on the steering
wheel (see page ).
When you unlock and open the
driver’s door, the display shows
‘‘DRIVER 1’’ or ‘‘DRIVER 2’’
depending on which remote
transmitter/keyless access remoteyou use, and the driver’s seat and the
outside mirrors move to the position
stored in that remote transmitter/
keyless access remote (see page
).
The driver’s ID (1 or 2) is displayed
when the power mode is set to ON.
The multi-inf ormation display in the
instrument panel displays various
inf ormation and messages when the
ignition switch is in the ON (II)
position. Some of the messages help
you operate your vehicle more
comf ortably. Others help to keep
you aware of the periodic
maintenance your vehicle needs f or
continued trouble-f ree driving.
Models equipped with the
keyless access system have an
engine start/stop button instead
of an ignition switch. ON Mode
is the equivalent of ON (II). For
more inf ormation, see pagesand .
There are three types of messages:
normal display messages, engine oil
lif e and maintenance messages, and
system messages. 78
164
: 178 181
On models with keyless access system
Multi-Inf ormation Display
Normal Display Messages
Inst rument s and Cont rols
77
Remote transmitter/keyless
access remote 1 is used.
Remote transmitter/keyless
access remote 2 is used.
09/07/29 16:55:27 31TK4610_082
2010 TL

ÎÎ
Î
ÛÝ
Î
ÛÝ
These messages go of f af ter several
seconds.
With the ignition switch in the ON
(II) position, the multi-inf ormation
display changes as shown on pageeach time you press the INFO
( / ) button or the SEL/RESET
button.
When you turn the ignition switch
to the ON (II) position, your last
selection is displayed.
Models equipped with the
keyless access system have an
engine start/stop button instead
of an ignition switch. ON Mode
is the equivalent of ON (II). For
more inf ormation, see pages
and .
If you do not f asten your seat belt,
you will also see a ‘‘FASTEN SEAT
BELT’’ message on the multi-
inf ormation display when you turn
the ignition switch to the ON (II)
position.
These messages go of f several
seconds af ter the key is inserted into
the ignition switch. 80
:
178 181
On models with keyless access system
Multi-Inf ormation Display
78
SEL/RESET BUTTON
INFO BUTTONS ( / )
A/T model is shown.
09/07/29 16:55:36 31TK4610_083
2010 TL

Î
CONT INUED
In the multi-information display, the
system message is also displayed
(see page ) and you can
customize your vehicle control
settings (see page ).In the normal display mode, the
upper segment displays trip
computer inf ormation, such as f uel
economy or average speed. The
lower segment displays the
odometer/trip meter (A/B), outside
temperature, and engine oil lif e and
maintenance item code(s).
The multi-inf ormation display
consists of an upper segment and a
lower segment. You will see some keyless access
system messages until you select the
ON mode by operating the engine
start/stop button. These messages
canbecustomized(seepage ).
Models equipped with the
keyless access system have an
engine start/stop button instead
of an ignition switch. ON Mode
is the equivalent of ON (II). For
more inf ormation, see pages
and . 87
:
178 181 92
106
On models with keyless access system
Multi-Inf ormation Display
Inst rument s and Cont rols
79
LOWER
SEGMENT
UPPER
SEGMENT
U.S. model is shown.
09/07/29 16:55:46 31TK4610_084
2010 TL

ÛÝ
Î
ÎÎ Î
Multi-Inf ormation Display
80
U.S. model is shown.
: Press the INFO button ( / ).
: Press the SEL/RESET button.
1:
2 : SH-AWD models only Odometer (See page
81.)
Trip Meter (See page 81.)
Trip Computer (See page 82.) Engine Oil Life
(See page
84.)
Tire Pressure for each tire (See page 85.)
HFL (See page 86.) Outside Temperature (See page
84.)
SH-AWD Torque Distribution Monitor
(See page 85.)
Keyless Memory Settings (See page 92.)
On models without navigation system only
This display will be shown when theBluetoothHandsFreeLinkis activated.
1 2
TM
09/07/29 16:55:54 31TK4610_085
2010 TL

Î
ÎThis shows your instant f uel
economy.
This shows the time passed traveled
since you last reset it. When you turn
the ignition switch to the ON (II)
position, ELAPSED TIME A or B is
reset.
Models equipped with the
keyless access system have an
engine start/stop button instead
of an ignition switch. ON Mode
is the equivalent of ON (II). For
more inf ormation, see pagesand .
This shows your vehicle’s average
f uel economy in mpg (U.S. models)
or liter/100 km (Canadian models)
since you last reset Trip A or Trip B.
You can customize the Trip A and
AVG. FUEL A reset condition on the
multi-inf ormation display (see page
).
This shows the average speed you
are traveling in miles per hour (mph)
forU.S.modelsorkilometersper
hour (km/h) f or Canadian models. This shows the estimated distance
you can travel on the fuel remaining
in the f uel tank. This distance is
estimated f rom the f uel economy
you received over the last several
miles (U.S.) or kilometers (Canada),
so it will vary with changes in speed,
traf f ic, etc.
:
178
102
181
INST . MPG (U.S. models)/INST . L /100 km (Canadian models)
EL A PSED T IME A /B
AVG. FUEL A/B
A VG. SPEED A /B RANGE
Multi-Inf ormation Display
Inst rument s and Cont rols
83
09/07/29 16:56:29 31TK4610_088
2010 TL

This shows the outside Fahrenheit
temperature in U.S. models, and
Celsius temperature in Canadian
models.In certain weather conditions,
temperature readings near f reezing
(32°F, 0°C) could mean that ice is
f orming on the road surf ace.
You can adjust the outside
temperature display (see page ). The temperature sensor is in the
f ront bumper. The temperature
reading can be affected by heat
ref lection f rom the road surf ace,
engine heat, and the exhaust f rom
surrounding traf f ic. This can cause
an incorrect temperature reading
when your vehicle speed is under
19 mph (30 km/h). When you start
your trip, the sensor is not f ully
acclimatized, theref ore it may take
several minutes until the proper
temperature is displayed.
This shows the remaining engine oil
lif e. It shows 100% af ter the engine
oil is replaced and the display is reset.
The engine oil lif e is calculated
based on engine operating conditions.
For more inf ormation, see page .
101 497
Multi-Inf ormation Display
Outside Temperature
Engine Oil Lif e
84
OUTSIDE TEMPERATURE ENGINE OIL LIFE
U.S. CANADA
U.S. model is shown.
09/07/29 16:56:39 31TK4610_089
2010 TL

ÛÝÛÝ
ÛÝ
If there is a problem with your
vehicle, f or example the engine oil
level is low or a door is not f ully
closed, the multi-inf ormation display
will show you the problem. It does
this by interrupting the current
display with one or more messages. The system message(s) triggers the
appropriate indicator(s) on the
instrument panel, including the
system message indicator, to come
on. The system message indicator
does not go of f until the problem(s)
is corrected.
You will also hear a beep when the
system message comes on f or the
first time.
Most of the messages are displayed
f or about 5 seconds, and then the
normal display returns. If there are
several system messages to be
shown, the display switches these
messages every 5 seconds.
To switch the message(s) bef ore 5
seconds have elapsed, press the
INFO( / )buttononthesteering
wheel.
Even if you press the INFO ( / )
button, some messages stay on or
come on again at regular intervals
until the problem is corrected.
If the system message indicator
remains lit on the instrument panel,
you can see the corresponding
message(s) again by pressing the
INFO ( / ) button repeatedly.
Here is a list of all messages:
CONT INUED
System Messages
Multi-Inf ormation Display
Inst rument s and Cont rols
87
SYSTEM MESSAGE INDICATOR
A/T model is shown.
09/07/29 16:57:08 31TK4610_092
2010 TL