2010.5 PEUGEOT 5008 ECO mode
[x] Cancel search: ECO modePage 193 of 345
159
Stopping the vehicle
Before switching off the engine, you
can engage position P or N to place the
gearbox in neutral.
In both cases, apply the parking brake
to immobilise the vehicle, unless it is
programmed to automatic mode.
Operating fault
When the ignition is on, the
lighting of this warning lamp,
accompanied by an audible
signal and a message in the
multifunction screen, indicates
a gearbox malfunction.
In this case, the gearbox switches to
back-up mode and is locked in 3rd gear.
You may feel a substantial knock when
changing from P to R and from N to R .
This will not cause any damage to the
gearbox.
Do not exceed 60 mph (100 km/h), local
speed restrictions permitting.
Have it checked by a PEUGEOT dealer.
This warning lamp may also come on if
a door is opened.
You risk damaging the gearbox:
Manual operation
Select position M for sequential
changing of the six gears.
Push the lever towards the + sign to
change up a gear.
Pull the lever towards the - sign to
change down a gear.
D disappears and the gears
engaged appear in succes-
sion in the instrument panel.
If the lever is not in posi-
tion P , when the driver's
door is opened or approxi-
mately 45 seconds after the ignition
is switched off, an audible signal is
heard and a message appears.
Return the lever to position P ; the
audible signal stops and the mes-
sage disappears.
It is only possible to change from one
gear to another if the vehicle speed and
engine speed permit; otherwise, the
gearbox will operate temporarily in au-
tomatic mode.
Invalid value during manual
operation
This symbol is displayed if a
gear is not engaged correctly
(selector between two posi-
tions).
It is possible to change from position D
(automatic) to position M (manual) at
any time.
When the vehicle is stationary or mov-
ing very slowly, the gearbox selects
gear M1 automatically.
The sport and snow programmes do not
operate in manual mode.
If the engine speed is too low or too
h i g h , t h e g e a r s e l e c t e d fl a s h e s f o r a f e w
seconds, then the actual gear engaged
is displayed.
- if you press the accelerator and
brake pedals at the same time,
- if you force the lever from posi- tion P to another position when
t h e b a t t e r y i s fl a t .
To reduce fuel consumption when
stationary for long periods with the
e n g i n e r u n n i n g ( t r a f fi c j a m . . . ) , p o s i -
tion the gear lever at N and apply
the parking brake, unless it is pro-
grammed in automatic mode.
Page 220 of 345
PRACTICAL INFORMATION
186
Changing sidelamp and daytime
running lamp bulbs (models with
xenon headlamps)
Remove the protective plastic cover
by pulling on the tab.
Disconnect the bulb connector.
Remove the bulb by pulling and
change it.
T o r e fi t , c a r r y o u t t h e s e o p e r a t i o n s i n
reverse order. Changing foglamp bulbs
You can also contact a
PEUGEOT dealer to have
these bulbs changed. Consult a PEUGEOT dealer.
Insert a screwdriver towards the
centre of the repeater between the
repeater and the base of the mirror.
Tilt the screwdriver to extract the re-
peater and remove it.
Disconnect the repeater connector.
T o r e fi t , c a r r y o u t t h e s e o p e r a t i o n s i n r e -
verse order.
Contact a PEUGEOT dealer to obtain
replacement repeaters.
Changing integrated direction
indicator side repeaters
Changing direction
indicator bulbs
Changing dipped beam
and main beam headlamp
bulbs (models with xenon
headlamps)
D1S xenon bulbs must be changed
by a PEUGEOT dealer as there is a
risk of electrocution.
It is recommended that the D1S bulbs
are changed at the same time when
one of them fails.
Consult a PEUGEOT dealer.
Page 232 of 345
PRACTICAL INFORMATION
198
Let the engine run for the
d u r a t i o n s p e c i fi e d t o e n s u r e
that the battery charge is suf-
fi c i e n t .
Do not repeatedly and continuously
restart the engine in order to charge
the battery.
A fl a t b a t t e r y p r e v e n t s t h e e n g i n e
from starting (refer to the "Battery"
paragraph). If the telephone is being used
at this time:
- it will be maintained for 5 min- utes with the hands-free kit of
your Peugeot Connect Sound or
Peugeot Connect Navigation,
- i t w i l l s t i l l b e p o s s i b l e t o fi n i s h t h e call with the Peugeot Connect
Media.
Exiting economy mode
These functions are reactivated auto-
matically next time the vehicle is driven.
In order to resume the use of these
functions immediately, start the en-
gine and let it run:
- for less than ten minutes, to use the equipment for approximately
fi v e m i n u t e s ,
- for more than ten minutes, to use the equipment for up to approxi-
mately thirty minutes.
CHANGING A WIPER BLADE
Removing
Raise the corresponding wiper arm.
Unclip the wiper blade and remove it.
Fitting
Put the corresponding new wiper
blade in place and clip it.
Fold down the wiper arm carefully.
Before removing a front wiper
blade
Within one minute after switching off
the ignition, operate the wiper stalk
to position the wiper blades verti-
cally on the windscreen.
After fitting a front wiper blade
Switch on the ignition.
Operate the wiper stalk again to
park the wiper blades.
LOAD REDUCTION MODE
System which manages the use of certain
functions according to the level of charge
remaining in the battery.
When the vehicle is being driven, the load
reduction function temporarily deactivates
certain functions, such as the air condi-
tioning, the heated rear screen...
The deactivated functions are reactivat-
ed automatically as soon as conditions
permit.
ENERGY ECONOMY MODE
System which manages the duration of
use of certain functions to conserve a
s u f fi c i e n t l e v e l o f c h a r g e i n t h e b a t t e r y .
After the engine has stopped, you can
still use functions such as the audio and
telematics system, windscreen wip-
ers, dipped beam headlamps, courtesy
lamps, etc. for a maximum combined
duration of thirty minutes.
Switching to economy mode
Once the thirty minutes are over, a
message appears in the multifunction
screen indicating that the vehicle has
switched to economy mode and the
active functions are put on standby.
Page 245 of 345
TECHNICAL DATA
210
WEIGHTS AND TOWED LOADS - 5008 5-seat LCV (in kg)
Engine
1.6 litre Turbo HDi
110 hp
2 litre Turbo HDi
150 hp
Gearbox Manual
(6-speed)
Electronic gear control (6-speed) Manual
(6-speed) Manual
(6-speed)
Model codes 9HZ 9HZ 9HR RHE
- Unladen weight 1 481 1 482 1 481 1 572
- Kerb weight * 1 556 1 557 1 556 1 6 47
- Gross vehicle weight (GVW) ** 2 225 2 230 2 200 2 310
- Gross train weight (GTW)
on a 12 % gradient *** 3 120 3 170 3 475
- Braked trailer (within GTW limit)
on a 10 % or 12 % gradient **** 895 890 970 1 165
- Braked trailer (with load transfer within the GTW limit) X X X X
- Unbraked trailer 750 750
- Recommended nose weight 70 70
* The kerb weight is equal to the unladen weight + driver (75 kg).
* * E x c e e d i n g t h e m a x i m u m r e a r a x l e w e i g h t i n v o l v e s l i m i t i n g t h e s p e e d t o 5 0 m p h ( 8 0 k m / h ) a s d e fi n e d i n p o i n t 2 . 7 o f t h e
Directive.
* * * E x c e e d i n g t h e g r o s s v e h i c l e w e i g h t w h e n t h e v e h i c l e i s t o w i n g i n v o l v e s l i m i t i n g t h e s p e e d t o 5 0 m p h ( 8 0 k m / h ) a s d e fi n e d
in point 2.7 of the Directive.
**** Maximum braked trailer weight within the GTW limit ; warning, towing using a lightly loaded towing vehicle may have an
adverse effect on its road holding.
The GTW and towed load values indicated are valid up t o a maximum altitude of 1 000 metres; the towed load mentio ned
must be reduced by 10 % for each additional 1 000 metres of a ltitude.
High ambient temperatures may result in a reduction in the pe rformance of the vehicle to protect the engine; if the ambient
temperature is above 37 °C, limit the towed load.
Page 250 of 345
217
2
ABC 3
DEF
5
JKL
4
GHI 6
MNO
8
TUV
7
PQRS 9
WXYZ
0
* #
1
RADIO MEDIA
NAV ESC TRAFFIC
SETUP
ADDR BOOK
The Peugeot Connect Media is protected in such a way that it will only operate in your vehicle. If it is to
be installed in another vehicle, contact a PEUGEOT dealer f o r c o n fi g u r a t i o n o f t h e s y s t e m .
Certain functions described in this handbook will become available during the course of the year.
PEUGEOT CONNECT MEDIA
For safety reasons, it is imperative that the driver carries out operations which require prolonged attention while the vehicle is stationary.
When the engine is switched off and to prevent discharging of the battery, the Peugeot Connect Media switches off following the activation of the Energy Economy mode.
01 First steps
02 Voice commands and steering
mounted controls
03 General operation
04 Navigation - Guidance
05 Traffic information
06 Radio
07 Music media players
08 Using the telephone
09 Configuration
10 Screen menu map p.
p.
p.
p.
p.
p.
p.
p.
p.
p. 218
220
223
228
237
239
240
245
249
250
CONTENTS
Frequently asked questions p. 255
MULTIMEDIA AUDIO SYSTEM/BLUETOOTH TELEPHONE
GPS EUROPE
Page 256 of 345
223
03
SETUP
TRAFFIC
MEDIA
GENERAL OPERATION
For a detailed global view of the menus available, refer tothe "Screen menu map" section of this handbook.
Press the MODE button several times in succession to gain access to the following displays:
Long press: access to the GPS coverage and to the demonstration mode.
For maintenance of the screen, the use of a soft, non-abrasive cloth (spectacles cloth) is recommended, without any addi tional product.
RADIO / MUSIC MEDIA/VIDEO
TELEPHONE (If a conversation is in progress)
FULL SCREEN MAP
NAVIGATION
(If guidance is in progress)
SETUP:
access to the "SETUP" Menu: system language * and voice functions * , voice initialisation (section 09), date and time * , display, unit and system parameters.
TRAFFIC:
a c c e s s t o t h e T r a f fi c M e n u : d i s p l a y o f t h e c u r r e n t t r a f fi c a l e r t s .
DISPLAY ACCORDING TO THE CONTEXT
MEDIA:
"DVD-audio" menu
"DVD-Video" menu
* Available according to model.
Page 273 of 345
240
07 MUSIC MEDIA PLAYERS
CD, MP3/WMA CD, MP3/WMA SD CARD/
USB PLAYER
In order to be able to play a recorded CDR or CDRW, when recording it is preferable to select the ISO 9660 level 1, 2 or Joliet standard.
If the disc is recorded in another format it may not be played correctly.
It is recommended that the same recording standard is always used for an individual disc, with as low a speed as possible(4x maximum) for optimum sound quality.
In the particular case of a multi-session CD, the Joliet standard is recommended.
T h e a u d i o e q u i p m e n t w i l l o n l y p l a y a u d i o fi l e s w i t h t h e e x t e n s i o n ".mp3" with a speed of between 8 Kbps and 320 Kbps and the extension ".wma" with a speed of between 5 Kbps and 384 Kbps.
It also supports the VBR (Variable Bit Rate) mode.
N o o t h e r t y p e o f fi l e ( . m p 4 , . m 3 u . . . ) c a n b e p l a y e d .
The MP3 format, an abbreviation of MPEG 1, 2 & 2.5 Audio Layer 3 and the WMA format, an abbreviation of Windows Media Audio and the property of Microsoft, are audio compression standards which p e r m i t t h e r e c o r d i n g o f s e v e r a l t e n s o f m u s i c fi l e s o n a s i n g l e d i s c .
Connecting an IPod:
T o p l a y M P 3 t y p e fi l e s , c o n n e c t t h e I P o d u s i n g t h e U S B p o r t (limited functions).
T o p l a y I T u n e s fi l e s , c o n n e c t t h e I P o d u s i n g t h e a u x i l i a r y s o c k e t ( A U X ) .
In order to be read, a USB memory stick must be formattedto FAT 32.
I t i s a d v i s a b l e t o r e s t r i c t fi l e n a m e s t o 2 0 c h a r a c t e r s , w i t h o u t u s i n g of special characters (e.g.: " " ? ; ù) to avoid any playing and displaying problems.
During play, exit the "SD-Card" or "USB" source before removing the SD card or the USB memory stick from its port.
To avoid any risk of theft, remove the SD card or the USB memory stick when you leave your vehicle with the roof open.
INFORMATION AND ADVICE
Page 282 of 345
249
09
1
4
5
2
ABC 3
DEF
5
JKL
4
GHI 6
MNO8
TUV
7
PQRS 9
WXYZ0
* #
1
RADIO MEDIA
NAV ESC TRAFFIC
SETUP
ADDR
BOOK
3
2
ABC 3
DEF
5
JKL
4
GHI 6
MNO8
TUV
7
PQRS 9
WXYZ0
* #
1
RADIO MEDIA
NAV ESC TRAFFIC
SETUP
ADDR
BOOK
2
ABC 3
DEF
5
JKL
4
GHI 6
MNO
8
TUV
7
PQRS 9
WXYZ
0
* #
1
NAV ESC TRAFFIC
ADDR
BOOKSETUPSETUP
2
ABC 3
DEF
5
JKL
4
GHI 6
MNO8
TUV
7
PQRS 9
WXYZ0
* #
1
RADIO MEDIA
NAV ESC TRAFFIC
SETUP
ADDR
BOOK
26
2
ABC 3
DEF
5
JKL
4
GHI 6
MNO8
TUV
7
PQRS 9
WXYZ0
* #
1
RADIO MEDIA
NAV ESC TRAFFIC
SETUP
ADDR
BOOK
2
ABC 3
DEF
5
JKL
4
GHI 6
MNO8
TUV
7
PQRS 9
WXYZ0
* #
1
RADIO MEDIA
NAV ESC TRAFFIC
SETUP
ADDR
BOOK
SETTING THE DATE AND TIME
Make the adjustments using the ring and move on to the next using the 4-direction navigator.
P r e s s O K t o c o n fi r m .
Select the "Date format" function and p r e s s O K t o c o n fi r m .
Select the format required using the r i n g a n d p r e s s O K t o c o n fi r m .
Select the "Set date & time" function a n d p r e s s O K t o c o n fi r m .
Pressing the SETUP button for more than 2 seconds permits access to:
This setting operation must be carried out if the battery h
as been disconnected.
Press the SETUP button.
Select the "Time format" function and p r e s s O K t o c o n fi r m .
Select the format required using the r i n g a n d p r e s s O K t o c o n fi r m .
Set date & time
Select the "Date & Time" function a n d p r e s s O K t o c o n fi r m .
Description of the unitDescription of the unit
GPS coverageGPS coverage
Demo mode
Date & Time
Principle of GPS synchronisation (GMT): 1 . C o n fi r m t h e " S y n c h r o n i s e w i t h G P S " s e l e c t i o n , t h e t i m e i s t h e n s e t t o GMT universal time, the date is also updated. 2 . U s i n g t h e 4 - d i r e c t i o n n a v i g a t o r , m o v e t h e c u r s o r t o t h e t i m e fi e l d s a n d press OK. 3. You can then use the ring to set the time to the time zone of your choice. Note that when changing between summer/winter time, the t ime zone must be changed again manually.