Page 65 of 336
63
COMFORT
FRONT SEATS
Seat consisting of a seat cushion, a seat
back and a head restraint which can all
be adjusted to adapt your position for
ease of driving and comfort.
Forwards-backwards adjustment
)
Raise the control and slide the seat
forwards or backwards.
Driver's or passenger's seat height
adjustment
)
Pull the control upwards to raise
or push it downwards to lower, as
many times as necessary, to obtain
the position required.
Seat back angle adjustment
)
Push the control rearwards.
Manual adjustments
Page 66 of 336
i
64
COMFORT
FRONT SEATS
Seat consisting of a seat cushion, a seat
back and a head restraint which can all
be adjusted to adapt your position for
ease of driving and comfort.
Forwards-backwards adjustment
)
Push the control forwards or
rearwards to slide the seat.
Seat cushion height and angle
adjustment
)
Tilt the rear part of the control
upwards or downwards to obtain the
required height.
)
Tilt the front part of the control
upwards or downwards to obtain the
required angle.
Seat back angle adjustment
)
Tilt the control forwards or rearwards
to adjust the angle of the seat back.
Driver's seat electric
adjustments
The electrical functions of the driv-
er's seat are deactivated approxi-
mately one minute after the ignition
is switched off.
To reactivate them, switch on the
ignition.
Page 67 of 336
i
!
65
COMFORT
Table position for front
passenger seat
Head restraint height adjustment
)
To raise the head restraint, pull it forwards
and upwards at the same time.
)
To remove the head restraint, press the
lug A
and pull the head restraint upwards.
)
To put the head restraint back in
place, engage the head restraint
stems in the openings keeping them
in line with the seat back.
)
To lower the head restraint, press the
lug A
and the head restraint at the
same time.
The head restraint is fi tted with a
frame with notches which prevents
it from lowering; this is a safety de-
vice in case of impact.
The adjustment is correct when
the upper edge of the head re-
straint is level with the top of the
head.
Never drive with the head restraints
removed; they must be in place and
adjusted correctly.
Lumbar adjustment
)
Turn the dial to obtain the correct
lumbar position.
Additional adjustments
Placing this seat in the table position, with
the rear seats also in the table position,
allows you to transport long objects.
)
Pull the control upwards to fold the
seat back onto the seat cushion.
To lower the seat back fully, tilt the
seat back angle adjustment control.
)
Pull the control again to release the
seat back and raise it.
When put back in place, the seat
back returns to its initial position.
Do not forget to fold the "aircraft"
type table fi xed on the back of the
seat fi rst.
Page 68 of 336
i
!
66
COMFORT
Storing driving positions
System which takes into account the
electrical settings of the driver's seat
and door mirrors. It enables you to store
up to two positions using the buttons on
the side of the driver's seat.
Ignition on or engine running
)
Briefl y press button 1
or 2
to recall
the corresponding position.
An audible signal is heard indicating the
end of the adjustment.
Storing a position Storing a new position cancels the
previous position.
Do not try to store a driving position
while driving.
Recalling a stored position
Vehicle moving
)
Press and hold button 1
or 2
until
the audible signal is heard indicating
the end of the adjustment.
Using buttons M/1/2
)
Switch on the ignition.
)
Adjust your seat and the door
mirrors.
)
Press button M
, then press button 1
or 2
within four seconds.
An audible signal is heard indicating
that the position has been stored. When the ignition is on, after a few
consecutive position recalls, the
function will be deactivated until
the engine is started, to prevent
discharging of the battery.
Heated seats control
With the engine running, the front seats
can be heated separately.
)
Use the adjustment dial, placed on
the side of each front seat, to switch
on and select the level of heating
required:
0:
Off.
1
:
Low.
2
:
Medium.
3
:
High.
Page 69 of 336
!
67
COMFORT
REAR SEATS
Never drive with the head restraints
removed; they must be in place
and in the high position when pas-
sengers are seated in the rear.
Rear head restraints
These have a high position (comfort
and safety) and a low position (rear visi-
bility).
They can also be removed.
To remove a head restraint:
)
pull the head restraint fully forwards
and upwards at the same time,
)
then, press the lug A
.
Removing the seat cushion
)
Move the corresponding front seat
forwards if necessary.
)
Raise the seat cushion 1
lifting it
with a hand from the rear.
)
Tilt the seat cushion 1
fully against
the front seat.
)
Remove the seat cushion 1
from its
fi xings by pulling upwards.
Refitting the seat cushion
)
Position the seat cushion 1
vertically in
its fi xings.
)
Fold down the seat cushion 1
.
)
Press on the seat cushion to secure it.
Bench seat, the left-hand (2/3) or right-
hand (1/3) section of which can be folded
to adapt the boot load space.
Page 71 of 336
ii
i
69
COMFORT
REAR SEATS
Forwards-backwards adjustment
Seat back angle adjustment
)
Pull one of the straps B
, located
at the front of the seat, then adjust
the angle to one of the 7 positions
offered.
)
Release the strap to lock the seat
back in this position.
Table position
)
Raise the bar A
and slide the seat
forwards or backwards.
)
Place the head restraint in the low
position.
)
Pull one of the straps B
, located at
the front of the seat.
)
Fold the seat back fully onto the
seat cushion; the seat automatically
moves back fully.
)
Press on the seat back to lock it.
Folding
Once the seat has been placed in the
table position, carry out the following
operations:
)
move back the seat fully using the
bar A
,
)
raise the lever C
, located at the rear
right of the seat, to release the rear
feet,
)
raise the seat fully so that it remains
in the fully folded
position.
You can also carry out these oper-
ations from the 3rd row using one
of the straps B
, located at the rear
of the seat. These operations allow access to
the 3 rd row, exit from the 3 rd row
and folding of the seats from the
boot. In the 2nd row, these three seats are
identical and can be adjusted for your
comfort. They can be placed in the table
position, folded or removed to obtain a
variety of loading confi gurations. During the forwards-backwards and
seat back angle adjustment opera-
tions, take care not to apply any force
to the load space cover roller.
Page 73 of 336
!
71
COMFORT
ADDITIONAL SEATS
Table position
)
Place the head restraint in the low
position.
)
Pull the strap A
, located at the rear
left of the seat.
)
Fold the seat back onto the seat
cushion.
Folding
Once the seat has been placed in the
table position, carry out the following
operations:
)
remove the load space cover roller,
)
raise the bar B
, located at the rear of
the seat, to release the rear feet,
)
raise the seat and secure it to the
head restraint rod of the 2nd row
seat, using the integrated retaining
strap C
.
Removal
Once the seat has been folded, carry
out the following operations:
)
pull the red strap D
to release the
front feet of the seat,
)
lift the seat and carry it using the
carrying handle E
,
)
put the anchorage covers back in
place to obtain a fl at boot fl oor.
Never use the adjustment and re-
taining straps to remove, install
or carry a seat; use the carrying
handle E
provided for this purpose
(weight of the seat: approximately
15 kg). In the 3rd row, these two seats are iden-
tical and are used for the occasional
carrying of additional passengers. They
can be placed in the table position,
folded or removed to obtain a variety of
loading confi gurations.
Page 75 of 336
i
!
73
COMFORT
SEAT MODULARITY AND VARIOUSCONFIGURATIONS
Examples of configurations
7 seats
Operations to change the existing
confi guration must only be car-
ried out when stationary (see the
"Rear seats" and "Additional seats"
sections of the SW individual rear
seats).
Special features
The outer seats of the 2nd row can be
moved inwards, once the central seat
has been removed.
The 2nd
row seats can be installed in
the 3rd row.
Conversely, the 3rd row seats cannot
be installed in the 2nd row.
5 seats with additional seats folded Do not seat passengers in the 3rd
row if the 2nd row seats are in the
fully folded
position. Designed to be modular, your vehicle
offers numerous seat installation and
loading confi gurations.
