2010.5 Peugeot 308 CC Dag ESP
[x] Cancel search: ESPPage 3 of 280
!
!
!
FAMILIARISATION
OPENING
Retractable roof The operation of the roof is the ex-
clusive responsibility of the driver.
To avoid any risk of injury when
operating the roof, ensure that no
one is standing near the moving
parts.
You are strongly advised not to op-
erate the roof in strong winds. When washing your vehicle:
- lock the vehicle using the re-
mote control or the key,
- avoid spraying the upper part of the windows,
- keep the end of the high pres- sure nozzle at least 1 metre
from the windows and door
seals.
When the vehicle has been
washed or after rain, wait until the
roof has dried before opening it. It is preferable to operate the roof
with the engine running and the
vehicle stationary. Wait until the
end of operation message ap-
pears in the multifunction screen
before moving off.
The operation can only be car-
ried out when moving if the speed
i s b e l o w 6 m p h ( 1 0 k m / h ) , a n d
you are driving smoothly on level
ground.
After the roof has been operated
fully four times in succession, the
system switches to protection
mode temporarily to avoid dam-
age to the roof motors. Let the
system rest for approximately ten
minutes; if you are unable to oper-
ate the roof after this time, contact
a PEUGEOT dealer.
Preliminary conditions
Start the engine
You must ensure that:
- the electric windows are initialised ( s e e c o r r e s p o n d i n g s e c t i o n ) ,
- the ambient temperature is higher than -15 °C.
Precautions to be taken before
operating the roof
Park the vehicle on level ground.
Check that no objects could hinder
the operation of the roof:
- nothing should be placed on the moving rear shelf 1 , on the boot
screen 2 or on the side trims 3 ,
- if luggage is transported in the boot, it must not lift the boot
screen,
- any objects, such as a jacket or umbrella, placed in the boot, must
be secured using the luggage re-
taining net 4 .
Check that the boot screen 2 is se-
c u r e d fi r m l y .
Close the boot correctly.
Page 11 of 280
FAMILIARISATION
SEEING CLEARLY
Lighting
Ring A
Ring B Raise or lower the lighting stalk passing
the point of resistance; the correspond-
i n g d i r e c t i o n i n d i c a t o r s w i l l fl a s h u n t i l
the stalk is moved from this position.
Direction indicators
Switching on "AUTO"
Press the stalk down and release it.
80 Lighting off.
Automatic illumination of head-
lamps.
Sidelamps.
Dipped/main beam headlamps.
Front and rear foglamps.
S t a l k A : w i n d s c r e e n w i p e r s
85
Wipers
Switching off "AUTO"
Push the stalk up and return it to po-
sition "0" .
"Motorway" function
Press the lighting stalk up or down once,
without passing the point of resistance;
the corresponding direction indicators
w i l l fl a s h t h r e e t i m e s .
The use of this function is available re-
g a r d l e s s o f t h e s p e e d , b u t y o u w i l l fi n d i t
particularly useful when changing lane
on fast roads.
95
86
Page 13 of 280
FAMILIARISATION
MONITORING
Instrument panel Switch panel
A. With the ignition on, the needle should
indicate the level of fuel remaining.
B. With the engine running, its associ-
ated low level warning lamp should
switch off.
C.
With the ignition on, the oil level indicator
should display that the level is OK or correct,
according to version, for a few seconds.
If the levels are not correct, top up the
levels which are low. Lighting of the indicator lamp indicates
the status of the corresponding function.
A. Emergency call in progress.
169
B. Deactivation of the alarm interior
volumetric monitoring.
70
C. Central locking.
75
D. Deactivation of the ESP/ASR system.
99
E. Deactivation of the front and rear
parking sensors.
124
F. Access to PEUGEOT services.
169
1. With the ignition on, the orange and
red warning lamps come on.
2. With the engine running, these
warning lamps should go off.
If warning lamps remain on, refer to the
page concerned.
Warning lamps
19
23
Page 19 of 280
1
i
22
INSTRUMENTS and CONTROLS
* According to country.
Instrument panel navigator associated
with the Peugeot Connect Media
Main menu
Press button 1 to open the main
menu and select one of the following
functions:
- "Vehicle parameters",
- "Choice of language",
- "Choice of units".
Press button 2 or 3 to move on the
screen.
Press button 1 a g a i n t o c o n fi r m t h e
selection. Vehicle parameters
This menu allows you to activate or
deactivate certain driving and comfort
equipment:
- selective unlocking (refer to the
"Access" section),
- guide-me-home and welcome light- ing (refer to the "Visibility" section),
- interior mood lighting (refer to the "Visibility" section),
- daytime running lamps (refer to the "Visibility" section),
- directional headlamps (refer to the "Visibility" section),
- rear parking sensors (refer to the "Driving" section).
Choice of language
This menu allows you to select the lan-
guage used by the screen: Deutsch,
English, Espanol, Français, Italiano,
Nederlands, Portugues, Türkçe * .
Choice of units
This menu allows you to select the units:
temperature (°Celsius or °Fahrenheit)
and fuel consumption (mpg, km/l or
l/100 km).
This group of buttons permits:
-
when stationary , c o n fi g u r a t i o n o f
the vehicle's equipment and the
central screen settings (language,
units...),
- while driving , scrolling through the
active functions (trip computer, navi-
gation...).
Controls
There are four buttons to control the in-
strument panel large screen:
1. a c c e s s t h e m a i n m e n u , c o n fi r m t h e
selection,
2. move up through the menu,
3. move down through the menu,
4. return to the previous screen, exit
from the menu. The main menu and its associated
functions can only be accessed
when stationary, via buttons
1 to 4 .
A message appears in the cen-
tral screen, above a certain speed
threshold, indicating that the main
menu cannot be displayed.
Trip computer information can only
be displayed while driving, using
buttons 2 and 3 (refer to the "Trip
computer" section).
Page 22 of 280
1
25
INSTRUMENTS and CONTROLS
Deactivation warning lamps
If one of the following warning lamps
c o m e s o n , t h i s c o n fi r m s t h a t t h e c o r r e -
sponding system has been switched off
intentionally. Passenger's airbag system
deactivation.
The passenger's airbag system
is put into service automatically
when the vehicle is started.
A s p e c i fi c c o n t r o l s w i t c h , l o c a t e d o n t h e
passenger's side of the dashboard, per-
mits deactivation of the system. This is
c o n fi r m e d b y c o n t i n u o u s l i g h t i n g o f t h i s
warning lamp on the instrument panel
or on the seat belt and passenger's
front airbag warning lamps display. Dynamic stability control
(ESP/ASR) deactivation
The ESP/ASR system is put
into service automatically when
the vehicle is started.
Common deactivation warning lamps S p e c i fi c d e a c t i v a t i o n w a r n i n g l a m p s Automatic locking.
If this is displayed, it indicates
that you have deactivated the
automatic locking of the doors
and boot while driving.
Automatic rain sensitive
windscreen wipers.
If this is displayed, it indicates that
you have deactivated automatic
rain sensitive windscreen wipers.
The other warning lamps appear on the
large screen, located in the centre of
the instrument panel.
Speed limiter.
If this is displayed, it indicates
that you have deactivated the
speed limiter.
Cruise control.
If this is displayed, it indicates
that you have deactivated the
cruise control.
Automatic illumination of
headlamps.
If this is displayed, it indicates
that you have deactivated auto-
matic illumination of headlamps.
A s p e c i fi c b u t t o n , l o c a t e d o n
the dashboard, permits deac-
tivation of the system. This is
c o n fi r m e d b y c o n t i n u o u s l i g h t -
ing of this warning lamp and of the indi-
cator lamp on the button.
From approximately 30 mph (50 km/h),
the system is reactivated automatically.
Page 24 of 280
1
!
27
INSTRUMENTS and CONTROLS
Engine self-diagnostic
system.
If this comes on, it indicates the
occurrence of a fault in the en-
gine management system.
I f i t fl a s h e s , i t i n d i c a t e s t h e o c c u r r e n c e o f
a fault in the emission control system.
Maximum coolant
temperature.
If this comes on, it indicates that
the temperature in the cooling
system is too high. Stop the vehicle as
soon as it is safe to do so.
Low fuel level.
W h e n t h i s fi r s t c o m e s o n , y o u
have approximately 6 litres of
fuel remaining in the tank.
Refuel as soon as possible to avoid run-
ning out of fuel. Airbags.
If this comes on, it indicates the
occurrence of a fault in one of
the airbag, roll-over hoop or
seat belt pretensioner systems.
Seat belt not fastened/
unfastened.
If this comes on, it indicates
that the driver and/or the front
passenger has not fastened or has un-
fastened their seat belt.
It also indicates that one or more rear
passengers have unfastened their seat
belt.
Water in Diesel * .
If this comes on, it indicates the
presence of water in the Diesel
fi l t e r .
There is a risk of damage to the injec-
tion system on Diesel engines. Door open.
A door or the boot is open:
Battery charge.
If this comes on, it indicates
the occurrence of a fault in the
battery charging circuit (dirty or
loose terminals, slack or cut alternator
belt...). Engine oil pressure.
If this comes on, it indicates the
occurrence of a fault in the en-
gine lubrication system. Stop
the vehicle as soon as it is safe
to do so.
S p e c i fi c w a r n i n g l a m p s
Dynamic stability control
(ESP/ASR).
The ESP/ASR system is put
into service automatically when
the vehicle is started.
Unless the system has been deactivated, if this
warning lamp and the indicator lamp on the
button come on continuously, this indicates the
occurrence of a fault in the ESP/ASR system.
* According to country.
-
if the speed is below 6 mph (10 km/h), this
warning lamp comes on continuously.
- if the speed is higher than 6 mph
(10 km/h), this warning lamp comes
on continuously, accompanied by an
audible signal.
Never continue to drive until you
run out of fuel, this could damage
the emission control and injection
systems.
Foot on brake.
Press the brake pedal to start
the engine with the automatic
gearbox. U n t i l s u f fi c i e n t f u e l h a s b e e n a d d e d , t h i s
warning lamp comes on again every the
ignition is switched on, along with an au-
dible signal and an alert message. When
driving, this audible signal and the display
of the message are repeated with increas-
ing frequency, as the fuel level drops to-
wards
"0" .
Capacity of the tank: approximately 60 litres .
Page 26 of 280
1
!
29
INSTRUMENTS and CONTROLS
Airbags.
If this is displayed, it indicates
the occurrence of a fault in one
of the airbag, roll-over hoop
or pretensioning seat belt sys-
tems.
Braking.
If this is displayed, it indicates
the occurrence of a fault in one
of the braking systems:
- s i g n i fi c a n t d r o p i n t h e fl u i d l e v e l i n the system,
- electronic brake force distribution (EBFD) fault (the ABS warning lamp
comes on as well).
Stop the vehicle as soon as it is safe to
do so.
If the vehicle is moving, check that the
parking brake is fully released. Anti-lock braking system
(ABS).
If this is displayed, it indicates
the occurrence of a fault in the
anti-lock braking system.
However, this does not prevent op-
eration of the vehicle's servo-assisted
braking.
Dynamic stability control
(ESP/ASR).
The ESP/ASR system is put into
service automatically when the ve-
hicle is started.
Unless the system has been deactivated, if
this warning lamp and the indicator lamp on
the button come on, this indicates the occur-
rence of a fault in the ESP/ASR system.
Door open.
A door or the boot is open:
Ice warning.
If this is displayed, it indicates
that there is risk of the forma-
tion of ice on the road below a
temperature of 3 °C.
Drive carefully. Parking brake.
If this is displayed, while the ve-
hicle is moving, it indicates that
the parking brake has not been
fully released.
Electronic immobiliser.
If this is displayed, it indicates
the occurrence of a fault in the
electronic engine immobiliser
system or that the remote control bat-
t e r y i s fl a t .
Fuel level.
W h e n t h i s fi r s t c o m e s o n , y o u
have approximately 6 litres of
fuel left in the tank.
It is imperative that you refuel to avoid
running out of fuel.
U n t i l s u f fi c i e n t f u e l h a s b e e n a d d e d , t h i s
warning lamp comes on again every
time the ignition is switched on, accom-
panied by an audible signal and an alert
message. When driving, this audible
signal and the display of the message
are repeated with increasing frequency
as the fuel level drops towards "0" .
Capacity of the tank: approximately
60 litres .
S c r e e n w a s h fl u i d l e v e l .
If this is displayed, following an
action on the wiper stalk, it indi-
c a t e s t h a t t h e fl u i d l e v e l i s l o w .
F i l l t h e s c r e e n w a s h / h e a d l a m p w a s h fl u -
id reservoir when you next stop. -
if the speed is below 6 mph (10 km/h),
this warning lamp is displayed in orange,
- if the speed is higher than 6 mph
(10 km/h), this warning lamp is dis-
played in red.
Coolant level.
If this is displayed, it indicates
a n i n s u f fi c i e n t l e v e l o f c o o l a n t i n
the system. Stop the vehicle as
soon as it is safe to do so.
Never continue to drive until you
run out of fuel, this could damage
the emission control and injection
systems.
Page 36 of 280
2
!
39
MULTIFUNCTION SCREENS
F o r s a f e t y r e a s o n s , c o n fi g u r a t i o n
of the multifunction screen by the
driver must be done only when sta-
tionary. "Telephone" menu
D i s p l a y c o n fi g u r a t i o n
Once this menu has been selected, you
have access to the following settings:
- brightness-video setting,
- date and time setting,
- choice of units.
Choice of language
Once this menu has been selected,
you can change the language used by
the display (Deutsch, English, Espanol,
Français, Italiano, Nederlands,
Portugues, Portugues-Brasil, Türkçe * ).
Example: setting of the duration of the
"guide-me-home" lighting
Press the " " or " " buttons, then
the "OK" button to select the menu
required.
Press the " " or " " buttons,
then the "OK" button to select the
"Guide-me-home headlamps" line.
Press the " " or " " buttons to set
the value required (15, 30 or 60 sec-
onds), then press the "OK" button
t o c o n fi r m .
Press the " " or " " buttons, then
the "OK" button to select the "OK"
b o x a n d c o n fi r m o r p r e s s t h e "ESC"
button to cancel. With the Peugeot Connect Sound
switched on, once this menu has
b e e n s e l e c t e d y o u c a n c o n fi g u r e y o u r
Bluetooth hands-free kit (pairing), con-
sult the various telephone directories
(calls log, services...) and manage your
communications (pick up, hang up, call
waiting, secret mode...).
For more information on the "Telephone"
application, refer to the Peugeot
Connect Sound part of the "Audio and
Telematics" section.
* According to country.