2010.5 Peugeot 107 Dag warning
[x] Cancel search: warningPage 21 of 97
1
23
INSTRUMENTS and CONTROLS
"2 TRONIC" GEARBOX
INDICATOR
Lever in EASY mode
(automatic mode)
"E" is displayed when this
operating mode is selected.
It goes off on switching to manual
mode.
Lever in manual mode
"M" is displayed when this
operating mode is selected.
It is switched off on switching
to EASY mode.
"Neutral"
"Reverse"
Operating mode:
1st
gear
2nd gear
3rd
gear
4th
gear
5th
gear
If this warning lamp comes
on with the engine running,
this indicates a fault with the
" 2 Tronic
" gearbox.
"!" warning lamp
Contact a PEUGEOT dealer or a
q u a l i fi e d w o r k s h o p .
Page 55 of 97
4
53
ACCESS
FUEL TANK
O p e n t h e f u e l fi l l e r fl a p .
Insert the key, turn it slightly to
the left then return to the right.
The key returns to its initial posi-
tion and the cap is unlocked.
Low fuel level
When the low fuel level is
r e a c h e d , t h e l a s t b a r fl a s h e s ,
accompanied by an audible
signal.
You have approximately
5 litres remaining.
In certain driving conditions and depend-
ing on the engine, the distance which
can be travelled with the fuel remaining
may be less than 30 miles (50 km).
W h e n t h e f r e q u e n c y o f t h e fl a s h i n g
increases, you have approximately
3 litres remaining .
Unscrew the cap and hook it onto
the clip located on the inside of
t h e fl a p .
A l a b e l a f fi x e d o n t h e i n s i d e o f t h e
fl a p r e m i n d s y o u w h i c h t y p e o f f u e l
to use.
W h e n y o u fi l l t h e f u e l t a n k , d o n o t
continue after the 3rd cut-off of the
pump. This could cause malfunc-
tions.
Remove the key.
If you run out of fuel, the
emission control system
warning lamp may come on
in the instrument panel. It will
go off automatically after the engine
has been started a few times.
T h e f u e l t a n k m u s t b e fi l l e d
with the engine switched
off .
The capacity of the fuel tank is ap-
proximately 35 litres.
A f t e r fi l l i n g t h e f u e l t a n k , s c r e w
the cap back on fully to the right
u n t i l i t c l i c k s a n d c l o s e t h e fl a p .
Page 57 of 97
5
55
VISIBILITY
LIGHTING STALK
1. Lamps off
2. Sidelamps
3. Dipped headlamps/
Main beam
headlamps Dipped/Main beam headlamps
Dipped beam headlamps: pull the
stalk.
Main beam headlamps: push the
stalk.
Lighting on audible warning
When the driver's door is opened
with the ignition off, a continuous au-
dible signal is heard if you have left
your lighting on. Rear foglamp
With the dipped head-
lamps on, selection is
by rotation of ring B for-
wards to switch on and
rearwards to switch off.
The status is displayed by the indica-
tor lamp in the instrument panel.
In clear weather or in rain,
both day and night, the rear
foglamp is dazzling and its
use is prohibited.
Direction indicators (flashers)
Left: stalk downwards.
Right: stalk upwards.
Headlamp flash
Pull the stalk fully towards you.
Front and rear lamps
Selection is by rotation of ring
A .
Switching to sidelamps does
not switch off the rear foglamp
if it is on.
Do not forget to switch them off when
they are no longer needed.
Page 60 of 97
6
58
SAFETY
HORN
Press one of the spokes of the steering
wheel.
HAZARD WARNING LAMPS
Press the button, the direction indica-
t o r s fl a s h .
They can operate with the ignition off.
ANTI-LOCK BRAKING SYSTEM (ABS) AND BRAKING SYSTEMS(EBFD AND CSC * )
When the vehicle is being driv-
en, illumination of this warning
lamp indicates that the park-
ing brake is still on or has not
been properly released.
When parking on a slope,
direct your wheels towards
the pavement and pull the
parking brake
on
.
PARKING BRAKE
Applying
Pull the parking brake to immobilise
your vehicle.
When changing wheels
(tyres), make sure that these
are approved.
The anti-lock braking system comes
into operation automatically when
there is a risk of wheel lock.
Releasing
Pull on the handle and press the but-
ton to release the parking brake.
* The CSC system is linked with the E B F D o n v e h i c l e s w h i c h a r e n o t fi t -
ted with ASR/ESP systems.
EMERGENCY BRAKING ASSISTANCE
The ABS, in conjunction with the
EBFD and CSC * braking systems,
increases the stability and manoeu-
vrability of your vehicle on braking
and provides improved control, in
particular on poor or slippery road
surfaces.
The ABS prevents wheel lock in the
event of emergency braking.
The EBFD and CSC * systems pro-
vide full control of the braking pres-
sure wheel by wheel. A distribution
between:
- the front and the rear in the case of the EBFD (Electronic Brake
Force Distribution),
- the left and the right in the case of the CSC * (Cornering Stability
Control).
In an emergency, this system enables
you to reach the optimum braking
pressure more quickly and therefore
reduce the stopping distance.
It is triggered by the speed at which
the brake pedal is pressed. This is
felt by a reduction in the resistance
of the pedal and an increase in the
effectiveness of the braking.
Page 61 of 97
6
58
SAFETY
HORN
Press one of the spokes of the steering
wheel.
HAZARD WARNING LAMPS
Press the button, the direction indica-
t o r s fl a s h .
They can operate with the ignition off.
ANTI-LOCK BRAKING SYSTEM (ABS) AND BRAKING SYSTEMS(EBFD AND CSC * )
When the vehicle is being driv-
en, illumination of this warning
lamp indicates that the park-
ing brake is still on or has not
been properly released.
When parking on a slope,
direct your wheels towards
the pavement and pull the
parking brake
on
.
PARKING BRAKE
Applying
Pull the parking brake to immobilise
your vehicle.
When changing wheels
(tyres), make sure that these
are approved.
The anti-lock braking system comes
into operation automatically when
there is a risk of wheel lock.
Releasing
Pull on the handle and press the but-
ton to release the parking brake.
* The CSC system is linked with the E B F D o n v e h i c l e s w h i c h a r e n o t fi t -
ted with ASR/ESP systems.
EMERGENCY BRAKING ASSISTANCE
The ABS, in conjunction with the
EBFD and CSC * braking systems,
increases the stability and manoeu-
vrability of your vehicle on braking
and provides improved control, in
particular on poor or slippery road
surfaces.
The ABS prevents wheel lock in the
event of emergency braking.
The EBFD and CSC * systems pro-
vide full control of the braking pres-
sure wheel by wheel. A distribution
between:
- the front and the rear in the case of the EBFD (Electronic Brake
Force Distribution),
- the left and the right in the case of the CSC * (Cornering Stability
Control).
In an emergency, this system enables
you to reach the optimum braking
pressure more quickly and therefore
reduce the stopping distance.
It is triggered by the speed at which
the brake pedal is pressed. This is
felt by a reduction in the resistance
of the pedal and an increase in the
effectiveness of the braking.
Page 62 of 97
6
59
SAFETY
When this warning lamp
comes on, it indicates that
there is a fault with the ABS,
which could cause a loss of
control of the vehicle when
braking.
Contact a PEUGEOT dealer or a
q u a l i fi e d w o r k s h o p .
When these warn-
ing lamps come on
simultaneously, it
indicates that there
is a fault with the braking system or
that the parking brake has not been
released fully, which can cause a
loss of control of the vehicle when
braking.
You must stop as soon as it is safe
to do so.
Contact a PEUGEOT dealer or a
q u a l i fi e d w o r k s h o p .
Normal operation of the ABS
may make itself felt by slight
vibrations of the brake pedal.
In emergency braking,
p r e s s v e r y fi r m l y w i t h o u t
releasing the pressure.
ANTI-SLIP REGULATION (ASR) AND ELECTRONIC STABILITY PROGRAMME (ESP)
Operating check
Operation of the ASR and ESP
systems
When one of these two sys-
tems is operating, this warn-
ing lamp comes on.
If a fault occurs with the
systems, this warning lamp
comes on. The ASR/ESP systems of-
fer exceptional safety dur-
ing normal driving, but this
should not encourage the
driver to take extra risks or drive at
high speed.
Correct operation of these systems
depends on observation of the ma-
nufacturer's recommendations regar-
ding the wheels (tyres and rims), the
braking components and the elec-
tronic components as well as the re-
pair procedures use by a PEUGEOT
d e a l e r o r q u a l i fi e d w o r k s h o p .
After an impact, have these systems
checked by a PEUGEOT dealer or a
q u a l i fi e d w o r k s h o p .
Contact a PEUGEOT dealer or a
q u a l i fi e d w o r k s h o p t o h a v e t h e s y s -
tems checked.
These systems are linked and sup-
plement the ABS.
The ASR system optimises drive to
prevent the wheels skidding, by act-
ing on the brakes of the driving wheels and on the engine. It also allows the
directional stability of the vehicle to
be improved on acceleration.
If there is a variation between the tra-
jectory followed by the vehicle and
that required by the driver, the ESP
system automatically acts on the
brake of one or more wheels and on
the engine to put the vehicle back on
course, within the limits of the laws
of physics.
Page 63 of 97
6
59
SAFETY
When this warning lamp
comes on, it indicates that
there is a fault with the ABS,
which could cause a loss of
control of the vehicle when
braking.
Contact a PEUGEOT dealer or a
q u a l i fi e d w o r k s h o p .
When these warn-
ing lamps come on
simultaneously, it
indicates that there
is a fault with the braking system or
that the parking brake has not been
released fully, which can cause a
loss of control of the vehicle when
braking.
You must stop as soon as it is safe
to do so.
Contact a PEUGEOT dealer or a
q u a l i fi e d w o r k s h o p .
Normal operation of the ABS
may make itself felt by slight
vibrations of the brake pedal.
In emergency braking,
p r e s s v e r y fi r m l y w i t h o u t
releasing the pressure.
ANTI-SLIP REGULATION (ASR) AND ELECTRONIC STABILITY PROGRAMME (ESP)
Operating check
Operation of the ASR and ESP
systems
When one of these two sys-
tems is operating, this warn-
ing lamp comes on.
If a fault occurs with the
systems, this warning lamp
comes on. The ASR/ESP systems of-
fer exceptional safety dur-
ing normal driving, but this
should not encourage the
driver to take extra risks or drive at
high speed.
Correct operation of these systems
depends on observation of the ma-
nufacturer's recommendations regar-
ding the wheels (tyres and rims), the
braking components and the elec-
tronic components as well as the re-
pair procedures use by a PEUGEOT
d e a l e r o r q u a l i fi e d w o r k s h o p .
After an impact, have these systems
checked by a PEUGEOT dealer or a
q u a l i fi e d w o r k s h o p .
Contact a PEUGEOT dealer or a
q u a l i fi e d w o r k s h o p t o h a v e t h e s y s -
tems checked.
These systems are linked and sup-
plement the ABS.
The ASR system optimises drive to
prevent the wheels skidding, by act-
ing on the brakes of the driving wheels and on the engine. It also allows the
directional stability of the vehicle to
be improved on acceleration.
If there is a variation between the tra-
jectory followed by the vehicle and
that required by the driver, the ESP
system automatically acts on the
brake of one or more wheels and on
the engine to put the vehicle back on
course, within the limits of the laws
of physics.
Page 65 of 97
6
61
SAFETY
The driver must ensure that
the passengers use the seat
belts correctly and that they
are all properly restrained
before setting off.
Wherever you are seated in the ve-
hicle, always fasten your seat belt,
even for short journeys.
Do not invert the seat belt buckles as
t h e y w i l l n o t f u l fi l t h e i r r o l e f u l l y .
If the seats have armrests * , the lap
part of the seat belt must always
pass under the armrest.
T h e s e a t b e l t s a r e fi t t e d w i t h a n i n -
ertia reel permitting automatic adjust-
ment of the length of the strap to your
size. The seat belt is stored automat-
ically when not in use.
Before and after use, ensure that the
seat belt is reeled in correctly.
The lower part of the strap must be
positioned as low as possible on the
pelvis.
The upper part must be positioned in
the hollow of the shoulder.
T h e i n e r t i a r e e l s a r e fi t t e d w i t h a n a u -
tomatic locking device which comes
into operation in the event of a colli-
sion, on emergency braking or if the
vehicle rolls over. You can release
the device by pulling rapidly on the
strap and releasing it. In order to be effective, a seat belt:
- must be tightened as close to the
body as possible,
- must restrain one adult only,
- must not bear any trace of cuts or fraying,
- must be pulled in front of you with a smooth movement, checking
that it does not twist,
- must not be transformed or m o d i fi e d t o a v o i d a l t e r i n g i t s
performance.
In accordance with current safety
regulations, all repairs and checks
must be carried out by a PEUGEOT
dealer who can guarantee that the
work is carried out correctly, or quali-
fi e d w o r k s h o p .
Have your seat belts checked regu-
larly by a PEUGEOT dealer or a
q u a l i fi e d w o r k s h o p a n d p a r t i c u l a r l y i f
the straps show signs of damage.
Clean the seat belt straps with soapy
water or a textile cleaning product,
sold by PEUGEOT dealers.
After folding or moving a seat or rear
bench seat, ensure that the seat belt
is positioned and rolled up correctly. Recommendations for children:
- use a suitable child seat if the
passenger is less than 12 years
o l d o r s h o r t e r t h a n o n e m e t r e fi f t y ,
- do not use the strap-guide * when a child seat is installed,
- never use the same seat belt to secure more than one person,
- never allow a child to travel on your lap.
Depending on the nature and se-
riousness of the impacts , the pre-
tensioning device may be triggered
before and independently of the air
bags. Triggering of the pre-tension-
ers is accompanied by a slight emis-
sion of harmless smoke and a noise,
due to the activation of the pyrotechnic
cartridge incorporated in the system.
In all cases, the airbag warning lamp
comes on.
Following an impact, have the seat
belts system checked, and if neces-
sary replaced, by a PEUGEOT dea-
l e r o r a q u a l i fi e d w o r k s h o p .
* According to model.