Page 50 of 341
Front seats Seat consisting of a seat cushion, a seat back and a head restraint which can all be adjusted to adapt your position for ease of driving and comfor t.
Manual adjustments
F o r w a r d s - b a c k w a r d s a d j u s t m e n t
Raise the control and slide the seat
for wards or backwards.
Driver's or passenger's seat h e i g h t a d j u s t m e n t
Pull the control upwards to raise or push it downwards to lower, as many times as necessary, to obtain the position required.
Seat back angle adjustment
Turn the control knob to adjust the seat
backrest angle.
As a safety measure, seat adjustments should only be done when stationary.
Page 51 of 341
Heated seats control
With the engine running, the front seats can be heated separately. Use the adjustment dial, placed on the side of each front seat, to switch on and select the level of heating required: 0: Off. 1: Low. 2: Medium. 3: High.
Additional adjustments
H e a d r e s t r a i n t h e i g h t a n d a n g l e adjustment
To raise a head restraint, pull it upwards. To remove the head restraint, press the lug A and pull the head restraint upwards. To put the head restraint back in place, engage the head restraint stems in the openings keeping them in line with the seat back. To lower the head restraint, press the lug Aand the head restraint at the same time. To adjust the angle of the head restraint, tilt its lower par t for wards or rear wards.
The head restraint is fitted with a frame with notches which prevents it from lowering; this is a safety device in case of impact. T h e a d j u s t m e n t i s c o r r e c t w h e n t h e u p p e r e d g e o f t h e h e a d r e s t r a i n t i s l e v e l w i t h t h e t o p o f t h e h e a d . Never drive with the head restraints removed; they must be in place and
adjusted correctly.
Page 53 of 341
87Comfort
Front seats
Seat consisting of a seat cushion, a seat back and a head restraint which can all be adjusted to adapt your position for ease of driving and comfor t.
Driver's seat electric adjustments
F o r w a r d s - b a c k w a r d s a d j u s t m e n t
Push the control for wards or rear wards to
slide the seat.
S e a t c u s h i o n h e i g h t a n d a n g l e adjustment
Tilt the rear par t of the control upwards or downwards to obtain the required height. Tilt the front par t of the control upwards or downwards to obtain the required angle.
Seat back angle adjustment
Tilt the control for wards or rear wards to
adjust the angle of the seat back.
The electrical functions of the driver's seat are deactivated approximately one minute after the ignition is switched off. To reactivate them, switch on the ignition.
Page 54 of 341
Heated seats control
With the engine running, the front seats can be heated separately. Use the adjustment dial, placed on the side of each front seat, to switch on and select the level of heating required: 0: Off. 1: Low. 2: Medium. 3: High.
Additional adjustments
H e a d r e s t r a i n t h e i g h t a n d a n g l e adjustment
To raise a head restraint, pull it upwards. To remove the head restraint, press the lug A and pull the head restraint upwards. To put the head restraint back in place, engage the head restraint stems in the openings keeping them in line with the seat back. To lower the head restraint, press the lug Aand the head restraint at the same time. To adjust the angle of the head restraint, tilt its lower par t for wards or rear wards.
The head restraint is fitted with a frame with notches which prevents it from lowering; this is a safety device in case of impact. T h e a d j u s t m e n t i s c o r r e c t w h e n t h e u p p e r e d g e o f t h e h e a d r e s t r a i n t i s l e v e l w i t h t h e t o p o f t h e h e a d . Never drive with the head restraints removed; they must be in place and
adjusted correctly.
Page 56 of 341
Rear seats
Move the corresponding front seat for ward if necessary. Position the seat belt between the outer and centre head restraints to avoid trapping the belt when repositioning the seat backrest. Place the head restraints in the low position.
F o l d i n g t h e b a c k r e s t
Pull control 1 for wards to release the seat back 2 . Fold the seat back 2 on to the cushion.
Straighten the seat back 2 and secure it. Check that the red indicator, located next to the control 1 , is no longer visible. Put the seat belt back in place on the side of the seat backrest.
R e p o s i t i o n i n g t h e s e a t b a c k r e s t
When repositioning the seat backrest, take care not to trap the seat belts.
Page 80 of 341
113Access
Boot
Unlocking the boot
Press this button to unlock the boot. As a safety measure, this action does
not unlock the doors.
Closing
Lower the boot lid using the interior grab handle.
If the tailgate is not closed correctly:
- when the engine is running , this warning lamp comes on, accompanied by a message in the multifunction screen for a few seconds,
- when the vehicle is moving (speed above 6 mph (10 km/h)), this warning lamp comes on, accompanied by an audible signal and a message in the multifunction screen for a few seconds.
System for mechanical unlocking of the boot in the event of a battery or central locking malfunction.
Tailgate release
Unlocking
Fold back the rear seats to gain access to the lock from inside the boot. Inser t a small screwdriver into hole Aof the lock to unlock the tailgate. After unlocking the boot or the vehicle using the remote control or the key, press the opening control, then raise the tailgate.
Opening
When the selective unlocking is activated, the boot can be opened at the second press of the unlocking button on the remote control.
Page 97 of 341
Automatic adjustment of Xenon headlamps
Do not touch the xenon headlamp bulbs. Contact a CITROËN dealer or a
qualified workshop.
In order to avoid causing a nuisance to other road users, this system corrects the height of the xenon headlamp beams automatically and when stationary, in relation to the load in the vehicle.
If a malfunction occurs, this warning lamp and/or the ser vice warning lamp is displayed on the instrument panel, accompanied by an audible signal and a message in the screen. The system then places your headlamps in the lowest position.
Manual adjustment
of halogen
headlamps
To avoid causing a nuisance to other road users, the height of the halogen headlamps should be adjusted according to the load in the vehicle. 0. 1 or 2 people in the front seats.
-. 3 people. 1. 5 people. -. Intermediate setting. 2. 5 people + maximum authorised load. -. Intermediate setting. 3. Driver + maximum authorised load.
The initial setting is position "0" .
Page 129 of 341
153Fittings
To remove the shelf: unhook the two cords, raise the shelf slightly, then remove it.
There are several options for storing the shelf: - either upright behind the front seats, - or flat at the base of the boot.
Rear parcel shelf
The hooks can be used to secure shopping bags.
Hooks
Access to the storage box
An additional hook under the shelf is used to hold up the boot floor using its cord, to facilitate access to the tools
and spare wheel or the temporary puncture repair kit...
