2010.5 Citroen DS4 lock
[x] Cancel search: lockPage 8 of 341
43Monitoring
Ser vice
temporarily, accompanied by a message.
A minor fault has occurred for which there is no specific warning lamp. Identify the fault by reading the message shown on the screen, such as, for example: - the opening of the doors, boot or bonnet, - the engine oil level, - the remote control battery,
- the tyre pressures, - saturation of the par ticle emission filter on Diesel vehicles (see "Checks - § Checks/Par ticle emissions filter"). For any other faults, contact a CITROËN dealer or a qualified workshop.
fixed, accompanied by a message and an audible signal.
A major fault has occurred for which there is no specific warning lamp. Identify the fault by reading the message shown on the screen and contact a CITROËN dealer or a qualified workshop.
Warning lampis onCauseAction/Obser vations
Par ticle emissions filter (Diesel)
fixed, accompanied by an audible signal
message on the risk of blockage of the par ticle emissions filter.
This indicates that the par ticle emissions filter is star ting to become
saturated.
As soon as driving conditions allow, regenerate the filter by driving at a speed of at least 35 mph (60 km/h)
until the warning lamp goes off.
fixed, accompanied by an audible signal and and a message that the
particle emissions filter additive level is too low.
This indicates the low level of the additive reser voir. Have the reser voir topped up as soon as possible by a CITROËN dealer or a qualified workshop.
Page 9 of 341
Warning lampis onCauseAction/Obser vations
Anti-lock Braking System (ABS) fixed. The anti-lock braking system has a fault. The vehicle retains conventional braking. Drive carefully at reduced speed and contact a CITROËN dealer or a qualified workshop without delay.
Dynamic stability control (ESP/ASR)
flashing. The ESP/ASR regulation is active. The system optimises traction and improves the directional stability of the vehicle.
fixed. Unless it has been deactivated (button pressed and its indicator lamp on), the ESP/ASR or hill star t assist system has a fault.
Have it checked by a CITROËN dealer or a qualified workshop.
Low fuel level fixed with the two last bars flashing. When it first comes on there remains approximately 6 litres of fuel in the tank.
You must refuel as soon as possible to avoid running out of fuel. This warning lamp will come on every time the ignition is switched on, until a sufficient addition of fuel is made. Fuel tank capacity: approximately 60 litres. Never continue to drive until you run out of fuel a s this could damage the emission control and injection systems.
Engine autodiagnosis system
fixed. The emission control system has a fault. The warning lamp should go off when the engine is started. If it does not go off, contact a CITROËN dealer or qualified workshop without delay.
flashing. The engine management system has a fault. Risk of destruction of the catalytic conver ter. Have it checked by a CITROËN dealer or a qualified workshop.
Page 19 of 341
A few seconds after the ignition is switched on, the distance recorder resumes its normal operation. The spanner remains on .
The distance remaining may be weighted by the time factor, depending on the type of driving. Therefore, the spanner may also come on if you have exceeded the two year ser vice inter val.
Service indicator zero reset
After each ser vice, the ser vice indicator must be reset to zero. The procedure for resetting to zero is as follows: switch off the ignition, press and hold the ".../000" trip distance recorder zero reset button, switch on the ignition; the distance recorder display begins a countdown, when the screen indicates "=/0" and the spanner disappears, release the button.
This operation cannot be carried out while a reminder of the ser vicing information is being displayed. Following this operation, if you wish to disconnect the battery, lock the vehicle and wait at least five minutes for the zero reset to be registered.
Recalling the service information
You can recall the ser vice information at any time. Briefly press the ".../000" trip distance recorder zero reset button. The ser vice information is displayed for a few seconds, in the total distance recorder line or in the instrument panel central colour screen, according to version.
Service overdue
For a few seconds after the ignition is switched on, the spanner flashes to indicate that the service must be carried out as soon as possible. Example: the ser vice is overdue by 180 miles (300 km). For a few seconds after the ignition is switched
on, the screen indicates:
Page 20 of 341
A few seconds after the ignition is switched on, the distance recorder resumes its normal operation. The spanner remains on .
The distance remaining may be weighted by the time factor, depending on the type of driving. Therefore, the spanner may also come on if you have exceeded the two year ser vice inter val.
Service indicator zero reset
After each ser vice, the ser vice indicator must be reset to zero. The procedure for resetting to zero is as follows: switch off the ignition, press and hold the ".../000" trip distance recorder zero reset button, switch on the ignition; the distance recorder display begins a countdown, when the screen indicates "=/0" and the spanner disappears, release the button.
This operation cannot be carried out while a reminder of the ser vicing information is being displayed. Following this operation, if you wish to disconnect the battery, lock the vehicle and wait at least five minutes for the zero reset to be registered.
Recalling the service information
You can recall the ser vice information at any time. Briefly press the ".../000" trip distance recorder zero reset button. The ser vice information is displayed for a few seconds, in the total distance recorder line or in the instrument panel central colour screen, according to version.
Service overdue
For a few seconds after the ignition is switched on, the spanner flashes to indicate that the service must be carried out as soon as possible. Example: the ser vice is overdue by 180 miles (300 km). For a few seconds after the ignition is switched
on, the screen indicates:
Page 22 of 341
The total and trip distances are displayed for thir ty seconds when the ignition is switched off, when the driver's door is opened and when the vehicle is locked or unlocked.
Distance recorders
Total distance recorder Trip distance recorder
Measures a distance travelled since it was reset to zero by the driver.
With the ignition on, press and hold this button until zeros appear.
Measures the total distance travelled by the vehicle since its first registration.
Page 47 of 341
83Comfort
S w i t c h i n g t h e s y s t e m o f f
Turn the air flow control to the left until all of the indicator lamps go off.
This switch does not operate the air conditioning, only the air fan. When the "REST" function is activated, you cannot modify the temperature, air flow and distribution settings: these are controlled automatically according to the ambient temperature. This function is not available in the STOP mode of Stop & Star t.
Avoid prolonged operation in interior air recirculation mode or driving for long periods with the system off (risk of
condensation and deterioration of air quality).
O n s w i t c h i n g o n t h e e n g i n e - The control screens come on: the function is available. - Pressing the REST button activates the ventilation for a few minutes. Activation of the function is confirmed by the display of two dashes in the control screens and four air flow level indicator lamps. - The function can be deactivated and reactivated if the control screens are on. - The screens go off at the end of this period.
O n s t o p p i n g t h e e n g i n e - While the control screens remain on: the function is available. - Pressing the REST button activates the ventilation for a few minutes. Activation of the function is confirmed by the display of two dashes in the control screens and four air flow level indicator lamps. Locking the vehicle has no effect on this function. - The control screens go off at the end of this period. Pressing again before the end of the period interrupts off the ventilation definitively: the control screens go off and the function is no longer available.
This action switches off the air conditioning and the ventilation. Temperature related comfor t is no longer assured but a slight flow of air, due to the movement of the vehicle, can still be felt. Modify the settings (temperature, air flow or air distribution) or press the "AUTO" button to reactivate the system with the values set before it was switched off.
Page 57 of 341
91Comfort
These have one position for use (up) and a stowed position (down). They can also be removed. To remove a head restraint: release the backrest using control 1 , tilt the backrest 2 slightly for wards,
pull the head restraint upwards to the stop, then, press the lug A .
R e a r h e a d r e s t r a i n t s
Never drive with the head restraints removed; they must be in place and correctly adjusted.
Steering wheel adjustment
W h e n s t a t i o n a r y , pull the control lever to W h e n s t a t i o n a r y W h e n s t a t i o n a r yrelease the steering wheel. Adjust the height and reach to suit your driving position. Push the control lever to lock the steering wheel.
As a safety precaution, these operations should only be carried out while the vehicle is stationary.
Page 58 of 341
91Comfort
These have one position for use (up) and a stowed position (down). They can also be removed. To remove a head restraint: release the backrest using control 1 , tilt the backrest 2 slightly for wards,
pull the head restraint upwards to the stop, then, press the lug A .
R e a r h e a d r e s t r a i n t s
Never drive with the head restraints removed; they must be in place and correctly adjusted.
Steering wheel adjustment
W h e n s t a t i o n a r y , pull the control lever to W h e n s t a t i o n a r y W h e n s t a t i o n a r yrelease the steering wheel. Adjust the height and reach to suit your driving position. Push the control lever to lock the steering wheel.
As a safety precaution, these operations should only be carried out while the vehicle is stationary.