Page 14 of 342
Lighting dimmer fixed. The lighting dimmer is making an adjustment. You can adjust the level of illumination of the instruments between 1 and 16.
Passenger's airbag system fixed on the seat belt and passenger's front airbag warning lamps display.
The control switch, located in the glove box, has been placed in the "ON" position.The passenger's front airbag is activated. In this case, do not install a "rear facing" child seat.
Move the control switch to the "OFF" position to deactivate the passenger's front airbag. In this case, you can install a "rear facing" child seat.
Automatic wiping fixed. The wiper control is pushed downwards. Automatic front wiping is activated.
Warning lampis onCauseAction/Obser vations
Stop & Star t
fixed. The Stop & Star t system has put the engine in STOP mode at a vehicle stop (traffic lights, traffic jam, or other...).
The warning lamp goes off and the engine restar ts automatically in START mode, as soon as you want to move off.
flashes for a few seconds, then goes off.
STOP mode is temporarily unavailable. or START mode is invoked automatically.
Refer to "Driving - § Stop & Star t" for special cases with STOP mode and START mode.
Parking space sensors fixed. The parking space sensors function is selected. To star t measurement, operate the direction indica tor on the side of the space to be measured, and do not exceed 12 mph (20 km/h). A message is displayed once the measurement has been completed.
Page 50 of 342
Front seats Seat consisting of a seat cushion, a seat back and a head restraint which can all be adjusted to adapt your position for ease of driving and comfor t.
Manual adjustments
F o r w a r d s - b a c k w a r d s a d j u s t m e n t
Raise the control and slide the seat
for wards or backwards.
Driver's or passenger's seat h e i g h t a d j u s t m e n t
Pull the control upwards to raise or push it downwards to lower, as many times as necessary, to obtain the position required.
Seat back angle adjustment
Turn the control knob to adjust the seat
backrest angle.
As a safety measure, seat adjustments should only be done when stationary.
Page 51 of 342
Heated seats control
With the engine running, the front seats can be heated separately. Use the adjustment dial, placed on the side of each front seat, to switch on and select the level of heating required: 0: Off. 1: Low. 2: Medium. 3: High.
Additional adjustments
H e a d r e s t r a i n t h e i g h t a n d a n g l e adjustment
To raise a head restraint, pull it upwards. To remove the head restraint, press the lug A and pull the head restraint upwards. To put the head restraint back in place, engage the head restraint stems in the openings keeping them in line with the seat back. To lower the head restraint, press the lug Aand the head restraint at the same time. To adjust the angle of the head restraint, tilt
its lower par t for wards or rear wards.
The head restraint is fitted with a frame with notches which prevents it from lowering; this is a safety device in case of impact. T h e a d j u s t m e n t i s c o r r e c t w h e n t h e u p p e r e d g e o f t h e h e a d r e s t r a i n t i s l e v e l w i t h t h e t o p o f t h e h e a d . Never drive with the head restraints removed; they must be in place and
adjusted correctly.
Page 53 of 342
87Comfort
Front seats
Seat consisting of a seat cushion, a seat back and a head restraint which can all be adjusted to adapt your position for ease of driving and comfor t.
Driver's seat electric adjustments
F o r w a r d s - b a c k w a r d s a d j u s t m e n t
Push the control for wards or rear wards to
slide the seat.
S e a t c u s h i o n h e i g h t a n d a n g l e adjustment
Tilt the rear par t of the control upwards or downwards to obtain the required height. Tilt the front par t of the control upwards or downwards to obtain the required angle.
Seat back angle adjustment
Tilt the control for wards or rear wards to
adjust the angle of the seat back.
The electrical functions of the driver's seat are deactivated approximately one minute after the ignition is switched off. To reactivate them, switch on the ignition.
Page 54 of 342
Heated seats control
With the engine running, the front seats can be heated separately. Use the adjustment dial, placed on the side of each front seat, to switch on and select the level of heating required: 0: Off. 1: Low. 2: Medium. 3: High.
Additional adjustments
H e a d r e s t r a i n t h e i g h t a n d a n g l e adjustment
To raise a head restraint, pull it upwards. To remove the head restraint, press the lug A and pull the head restraint upwards. To put the head restraint back in place, engage the head restraint stems in the openings keeping them in line with the seat back. To lower the head restraint, press the lug Aand the head restraint at the same time. To adjust the angle of the head restraint, tilt
its lower par t for wards or rear wards.
The head restraint is fitted with a frame with notches which prevents it from lowering; this is a safety device in case of impact. T h e a d j u s t m e n t i s c o r r e c t w h e n t h e u p p e r e d g e o f t h e h e a d r e s t r a i n t i s l e v e l w i t h t h e t o p o f t h e h e a d . Never drive with the head restraints removed; they must be in place and
adjusted correctly.
Page 56 of 342
Storing driving positions
System which registers the electrical settings of the driver's seat and door mirrors. It enables you to store and recall two positions using the buttons on the side of the driver's seat.
Storing a position
Using buttons M/1/2
Switch on the ignition. Adjust your seat and the door mirrors. Press button M , then press button 1 or 2within four seconds. An audible signal indicates that the position has been stored.
Recalling a stored position
Ignition on or engine running
Press button 1 or 2 to recall the corresponding position. An audible signal indicates the end of the adjustment.
Storing a new position cancels the previous position.
You can interrupt the current movement by pressing button M , 1 or 2 or by using one of the seat controls. A stored position cannot be recalled
while driving. Recalling stored positions is deactivated 45 seconds after switching off the ignition.
Page 97 of 342
Automatic adjustment of Xenon headlamps
Do not touch the xenon headlamp bulbs. Contact a CITROËN dealer or a
qualified workshop.
In order to avoid causing a nuisance to other road users, this system corrects the height of the xenon headlamp beams automatically and when stationary, in relation to the load in the vehicle.
If a malfunction occurs, this warning lamp and/or the ser vice warning lamp is displayed on the instrument panel, accompanied by an audible signal and a message in the screen. The system then places your headlamps in the lowest position.
Manual adjustment
of halogen
headlamps
To avoid causing a nuisance to other road users, the height of the halogen headlamps should be adjusted according to the load in the vehicle. 0. 1 or 2 people in the front seats.
-. 3 people. 1. 5 people. -. Intermediate setting. 2. 5 people + maximum authorised load. -. Intermediate setting. 3. Driver + maximum authorised load.
The initial setting is position "0" .
Page 155 of 342
Safety
Seat belts
Front seat belts
The front seat belts are fitted with a pretensioning and force limiting system. This system improves safety in the front seats in the event of a front or side impact.
Depending on the severity of the impact, the pretensioning system instantly tightens the seat belts against the body of the occupants. The pretensioning seat belts are active when the ignition is on. The force limiter reduces the pressure of the seat belt on the chest of the occupant, so improving their protection.
Fastening
Pull the strap, then inser t the tongue in the buckle. Check that the seat belt is fastened
correctly by pulling the strap.
Unfastening
Press the red button on the buckle. Guide the seat belt as it reels in.
Seat belt not fastened/unfastened warning lamp
When the ignition is switched on, this warning lamp comes on in the instrument panel if the driver and/or the front passenger has not fastened their seat belt. From approximately 12 mph (20 km/h) this warning lamp flashes for two minutes accompanied by an audible signal of increasing volume. Once these two minutes have elapsed, this warning lamp remains on until the driver and/
or the front passenger fastens their seat belt.
Height adjustment
To lower the attachment point, squeeze the control A and slide it downwards. To raise the attachment point, slide the control A upwards.
