2009 YAMAHA YZF-R1 light

MOTORCYCLE CARE AND STORAGE
7-2
7off any detergent residue using
plenty of water, as it is harmful
to plastic parts.


Do not use any harsh chemical
products on plastic parts or the
mufflers. Be sure to avoid using
cloths or sponges which have
been in contact with strong or
abrasive cleaning products, sol-
vent or thinner, fuel (gasoline),
rust removers or inhibitors,
brake fluid, antifreeze or electro-
lyte.


Do not use high-pressure wash-
ers or steam-jet cleaners since
they cause water seepage and
deterioration in the following ar-
eas: seals (of wheel and swing-
arm bearings, fork and brakes),
storage compartments, electric
components (couplers, connec-
tors, instruments, switches and
lights), breather hoses and
vents.


For motorcycles equipped with
a windshield: Do not use strong
cleaners or hard sponges as
they will cause dulling or
scratching. Some cleaning com-pounds for plastic may leave
scratches on the windshield.
Test the product on a small hid-
den part of the windshield to
make sure that it does not leave
any marks. If the windshield is
scratched, use a quality plastic
polishing compound after
washing.
After normal use
Remove dirt with warm water, a mild
detergent, and a soft, clean sponge,
and then rinse thoroughly with clean
water. Use a toothbrush or bottlebrush
for hard-to-reach areas. Stubborn dirt
and insects will come off more easily if
the area is covered with a wet cloth for
a few minutes before cleaning.
After riding in the rain, near the sea oron salt-sprayed roadsSince sea salt or salt sprayed on roads
during winter are extremely corrosive in
combination with water, carry out the
following steps after each ride in the
rain, near the sea or on salt-sprayed
roads.
TIPSalt sprayed on roads in the winter mayremain well into spring.
1. Clean the motorcycle with cold wa-
ter and a mild detergent, after the
engine has cooled down.
NOTICE: Do not use warm water
since it increases the corrosive
action of the salt.
[ECA10791]
2. After drying the motorcycle, apply
a corrosion protection spray on all
metal, including chrome- and nick-
el-plated, surfaces (except the tita-
nium mufflers) to prevent
corrosion.
Cleaning the titanium mufflersThis model is equipped with titanium
mufflers, which require the following
special care.

Use only a soft, clean cloth or
sponge with mild detergent and
water to clean the titanium muf-
flers. However, if the mufflers can-
not be thoroughly cleaned with
mild detergent, alkaline products
and a soft brush may be used.
U14BE0E0.book Page 2 Friday, November 21, 2008 9:23 AM

MOTORCYCLE CARE AND STORAGE
7-3
7


Never use compounds or other
special treatments to clean the tita-
nium mufflers, as they will remove
the finish on the outer surface of
the mufflers.


Even the smallest amounts of oil,
such as from oily towels or finger-
prints, will leave stains on the tita-
nium mufflers, which can be
removed with a mild detergent.


Note that the thermally induced
discoloring of the portion of the ex-
haust pipe leading into the titanium
mufflers is normal and cannot be
removed.
After cleaning
1. Dry the motorcycle with a chamois
or an absorbing cloth.
2. Immediately dry the drive chain
and lubricate it to prevent it from
rusting.
3. Use a chrome polish to shine
chrome, aluminum and stainless-
steel parts.4. To prevent corrosion, it is recom-
mended to apply a corrosion pro-
tection spray on all metal,
including chrome- and nickel-plat-
ed, surfaces.
5. Use spray oil as a universal clean-
er to remove any remaining dirt.
6. Touch up minor paint damage
caused by stones, etc.
7. Wax all painted surfaces.
8. Let the motorcycle dry completely
before storing or covering it.
WARNING
EWA11131
Contaminants on the brakes or tires
can cause loss of control.

Make sure that there is no oil or
wax on the brakes or tires.


If necessary, clean the brake
discs and brake linings with a
regular brake disc cleaner or ac-
etone, and wash the tires with
warm water and a mild deter-
gent. Before riding at higher
speeds, test the motorcycle’s
braking performance and cor-nering behavior.
NOTICE
ECA10800


Apply spray oil and wax spar-
ingly and make sure to wipe off
any excess.


Never apply oil or wax to any
rubber and plastic parts, but
treat them with a suitable care
product.


Avoid using abrasive polishing
compounds as they will wearaway the paint.
TIP

Consult a Yamaha dealer for ad-
vice on what products to use.


Washing, rainy weather or humid
climates can cause the headlight
lens to fog. Turning the headlight
on for a short period of time will
help remove the moisture from thelens.
U14BE0E0.book Page 3 Friday, November 21, 2008 9:23 AM

SPECIFICATIONS
8-2
8
Chassis:Frame type:
Diamond
Caster angle:
24.00 °
Trail:
102.0 mm (4.02 in)Front tire:Type:
Tubeless
Size:
120/70 ZR17M/C (58W)
Manufacturer/model:
MICHELIN/Pilot POWER P
Manufacturer/model:
DUNLOP/D210FRear tire:Type:
Tubeless
Size:
190/55 ZR17M/C (75W)
Manufacturer/model:
MICHELIN/ Pilot POWER
Manufacturer/model:
DUNLOP/D210Loading:Maximum load:
189 kg (417 lb)
(Total weight of rider, passenger, cargo and
accessories)Tire air pressure (measured on cold
tires):Loading condition:
0–90 kg (0–198 lb)Front:
250 kPa (2.50 kgf/cm², 36 psi)
Rear:
290 kPa (2.90 kgf/cm², 42 psi)
Loading condition:
90–189 kg (198–417 lb)
Front:
250 kPa (2.50 kgf/cm², 36 psi)
Rear:
290 kPa (2.90 kgf/cm², 42 psi)
High-speed riding:
Front:
250 kPa (2.50 kgf/cm², 36 psi)
Rear:
290 kPa (2.90 kgf/cm², 42 psi)
Front wheel:Wheel type:
Cast wheel
Rim size:
17M/C x MT3.50Rear wheel:Wheel type:
Cast wheel
Rim size:
17M/C x MT6.00Front brake:Type:
Dual disc brake
Operation:
Right hand operation
Recommended fluid:
DOT 4
Rear brake:Type:
Single disc brake
Operation:
Right foot operation
Recommended fluid:
DOT 4Front suspension:Type:
Telescopic fork
Spring/shock absorber type:
Coil spring/oil damper
Wheel travel:
120.0 mm (4.72 in)Rear suspension:Type:
Swingarm (link suspension)
Spring/shock absorber type:
Coil spring/gas-oil damper
Wheel travel:
120.0 mm (4.72 in)Electrical system:Ignition system:
TCI (digital)
Charging system:
AC magnetoBattery:Model:
YTZ10S
Voltage, capacity:
12 V, 8.6 AhHeadlight:Bulb type:
Halogen bulb
U14BE0E0.book Page 2 Friday, November 21, 2008 9:23 AM

SPECIFICATIONS
8-3
8
Bulb voltage, wattage × quantity:Headlight:
12 V, 55 W × 2
Tail/brake light:
LED
Front turn signal light:
12 V, 10.0 W × 2
Rear turn signal light:
12 V, 10.0 W × 2
Auxiliary light:
12 V, 5.0 W × 2
License plate light:
12 V, 5.0 W × 1
Meter lighting:
LED
Neutral indicator light:
LED
High beam indicator light:
LED
Oil level warning light:
LED
Turn signal indicator light:
LED
Fuel level warning light:
LED
Coolant temperature warning light:
LED
Engine trouble warning light:
LED
Steering damper warning light:
LED
Immobilizer system indicator light:
LEDShift timing indicator light:
LED
Fuses:Main fuse:
50.0 A
Headlight fuse:
20.0 A
Signaling system fuse:
7.5 A
Ignition fuse:
15.0 A
Radiator fan fuse:
15.0 A × 2
Turn signal light fuse:
7.5 A
Fuel injection system fuse:
15.0 A
Steering damper fuse:
7.5 A
Backup fuse:
7.5 A
Electronic throttle valve fuse:
7.5 A
U14BE0E0.book Page 3 Friday, November 21, 2008 9:23 AM

INDEXAAir filter element .................................... 6-17
Anti-theft alarm (optional)...................... 3-18
Auxiliary light bulb, replacing ................ 6-35BBattery................................................... 6-30
Brake and clutch levers, checking and
lubricating ........................................... 6-27
Brake and shift pedals, checking and
lubricating ........................................... 6-27
Brake fluid, changing ............................ 6-24
Brake fluid level, checking .................... 6-23
Brake lever ............................................ 3-21
Brake pedal ........................................... 3-21CCables, checking and lubricating .......... 6-26
Care ........................................................ 7-1
Catalytic converter ................................ 3-24
Clutch lever ........................................... 3-20
Clutch lever free play, adjusting ............ 6-21
Coolant.................................................. 6-14
Coolant temperature warning light .......... 3-5
Cowlings and panels, removing and
installing................................................ 6-7DDimmer switch ...................................... 3-19
D-mode (drive mode) .............................. 3-1
Drive chain, cleaning and lubricating .... 6-25
Drive chain slack ................................... 6-24EEngine break-in ....................................... 5-3
Engine idling speed, checking .............. 6-17
Engine oil and oil filter cartridge ............ 6-11
Engine stop switch ................................ 3-19Engine trouble warning light ................... 3-8
FFront and rear brake pads, checking .... 6-22
Front fork, adjusting .............................. 3-28
Front fork, checking .............................. 6-28
Fuel....................................................... 3-22
Fuel consumption, tips for reducing........ 5-3
Fuel level warning light ........................... 3-5
Fuel tank breather/overflow hose ......... 3-24
Fuel tank cap ........................................ 3-22
Fuses, replacing ................................... 6-31HHandlebar switches .............................. 3-18
Hazard switch ....................................... 3-19
Headlight bulb, replacing ...................... 6-32
Helmet holder ....................................... 3-26
High beam indicator light ........................ 3-5
Horn switch ........................................... 3-19IIdentification numbers ............................ 9-1
Ignition circuit cut-off system ................ 3-34
Immobilizer system ................................. 3-1
Immobilizer system indicator light........... 3-8
Indicator and warning lights .................... 3-4KKey identification number ....................... 9-1LLicense plate light bulb, replacing ........ 6-34
Luggage strap holders .......................... 3-33MMain switch/steering lock........................ 3-3
Maintenance and lubrication, periodic .... 6-3
Maintenance, emission control system... 6-2
Matte color, caution ................................ 7-1Model label .............................................. 9-2
Multi-function meter unit .......................... 3-9
NNeutral indicator light .............................. 3-5OOil level warning light .............................. 3-5PParking .................................................... 5-4
Part locations .......................................... 2-1
Pass switch ........................................... 3-19RRear brake light switch, adjusting ......... 6-22
Rear view mirrors .................................. 3-28
Rider footrest position, adjusting ........... 3-27SSafety information ................................... 1-1
Seats ..................................................... 3-25
Shifting .................................................... 5-2
Shift pedal ............................................. 3-20
Shift timing indicator light ........................ 3-8
Shock absorber assembly, adjusting .... 3-30
Sidestand .............................................. 3-33
Sidestand, checking and lubricating...... 6-28
Spark plugs, checking ........................... 6-10
Specifications .......................................... 8-1
Starting the engine .................................. 5-1
Start switch............................................ 3-19
Steering, checking................................. 6-29
Steering damper warning light ................ 3-8
Storage.................................................... 7-4
Storage compartment............................ 3-27
Supporting the motorcycle .................... 6-35TTail/brake light ....................................... 6-33
U14BE0E0.book Page 1 Friday, November 21, 2008 9:23 AM

INDEX
Throttle cable free play, checking ......... 6-17
Throttle grip and cable, checking and
lubricating ........................................... 6-26
Tires...................................................... 6-18
Tool kit .................................................... 6-1
Troubleshooting .................................... 6-39
Troubleshooting charts ......................... 6-41
Turn signal indicator lights ...................... 3-4
Turn signal light bulb, replacing ............ 6-34
Turn signal switch ................................. 3-19VValve clearance .................................... 6-18
Vehicle identification number.................. 9-1WWheel bearings, checking .................... 6-29
Wheel (front) ......................................... 6-36
Wheel (rear).......................................... 6-38
Wheels.................................................. 6-20
U14BE0E0.book Page 2 Friday, November 21, 2008 9:23 AM