2009 YAMAHA YZF-R1 lock

PERIODIC MAINTENANCE AND ADJUSTMENT
6-33
6 3. Unhook the headlight bulb holder,
and then remove the burnt-out
bulb.
4. Place a new headlight bulb into po-
sition, and then secure it with the
bulb holder.5. Connect the headlight coupler.
6. Install the headlight bulb cover by
turning it clockwise.
7. Have a Yamaha dealer adjust the
headlight beam if necessary.
EAU24181
Tail/brake light This model is equipped with an LED-
type tail/brake light.
If the tail/brake light does not come on,
have a Yamaha dealer check it.
1. Headlight coupler
1. Headlight bulb
2. Headlight bulb holder
1
12
U14BE0E0.book Page 33 Friday, November 21, 2008 9:23 AM

PERIODIC MAINTENANCE AND ADJUSTMENT
6-34
6
EAU24204
Replacing a turn signal light
bulb 1. Remove the turn signal light lens
by removing the screw.
2. Remove the burnt-out bulb by
pushing it in and turning it counter-
clockwise.
3. Insert a new bulb into the socket,
push it in, and then turn it clock-
wise until it stops.
4. Install the lens by installing the
screw. NOTICE: Do not over-
tighten the screw, otherwise the
lens may break.
[ECA11191]EAU24312
Replacing the license plate
light bulb 1. Remove the license plate light unit
by removing the screws.
2. Remove the socket (together with
the bulb) by pulling it out.3. Remove the burnt-out bulb by pull-
ing it out.
4. Insert a new bulb into the socket.
5. Install the socket (together with the
bulb) by pushing it in.
6. Install the license plate light unit by
installing the screws.
1. Screw
1
1. License plate light unit
2. Screw
1. License plate light bulb
1
2
1
U14BE0E0.book Page 34 Friday, November 21, 2008 9:23 AM

PERIODIC MAINTENANCE AND ADJUSTMENT
6-38
612. While applying the front brake,
push down hard on the handlebar
several times to check for proper
fork operation.
EAU25080
Rear wheel
EAU25312
To remove the rear wheel
WARNING
EWA10821
To avoid injury, securely support the
vehicle so there is no danger of itfalling over.
1. Loosen the axle nut.
2. Lift the rear wheel off the ground
according to the procedure on
page 6-35.
3. Remove the axle nut.4. Loosen the locknut on each side of
the swingarm.
5. Turn the drive chain slack adjust-
ing bolts fully in direction (a) and
push the wheel forward.
6. Remove the drive chain from the
rear sprocket.
TIP

If the drive chain is difficult to re-
move, remove the wheel axle first,
and then lift the wheel upward
enough to remove the drive chain
from the rear sprocket.


The drive chain cannot be disas-sembled.
7. While supporting the brake caliper
bracket, pull the wheel axle out,
and then remove the wheel.
NOTICE: Do not apply the brake
after the wheel has been re-
moved together with the brake
disc, otherwise the brake pads
will be forced shut.
[ECA11071]
Tightening torque:
Wheel axle pinch bolt:
21 Nm (2.1 m·kgf, 15 ft·lbf)
1. Axle nut
2. Brake caliper bracket
3. Brake caliper
4. Locknut
5. Drive chain slack adjusting bolt12
3
5
4(a)
U14BE0E0.book Page 38 Friday, November 21, 2008 9:23 AM

PERIODIC MAINTENANCE AND ADJUSTMENT
6-42
6Engine overheating
WARNING
EWAT1040


Do not remove the radiator cap when the engine and radiator are hot. Scalding hot fluid and steam may be
blown out under pressure, which could cause serious injury. Be sure to wait until the engine has cooled.


Place a thick rag, like a towel, over the radiator cap, and then slowly rotate the cap counterclockwise to the de-
tent to allow any residual pressure to escape. When the hissing sound has stopped, press down on the capwhile turning it counterclockwise, and then remove the cap.
TIPIf coolant is not available, tap water can be temporarily used instead, provided that it is changed to the recommended coolantas soon as possible.
Wait until the
engine has cooled.
Check the coolant level in the
reservoir and radiator.
The coolant level
is OK.The coolant level is low.
Check the cooling system
for leakage.
Have a Yamaha dealer checkand repair the cooling system.Add coolant. (See TIP.)
Start the engine. If the engine overheats again,
have a
Yamaha dealer check
and repair the cooling system.
There is
leakage.
There is
no leakage.
U14BE0E0.book Page 42 Friday, November 21, 2008 9:23 AM

INDEXAAir filter element .................................... 6-17
Anti-theft alarm (optional)...................... 3-18
Auxiliary light bulb, replacing ................ 6-35BBattery................................................... 6-30
Brake and clutch levers, checking and
lubricating ........................................... 6-27
Brake and shift pedals, checking and
lubricating ........................................... 6-27
Brake fluid, changing ............................ 6-24
Brake fluid level, checking .................... 6-23
Brake lever ............................................ 3-21
Brake pedal ........................................... 3-21CCables, checking and lubricating .......... 6-26
Care ........................................................ 7-1
Catalytic converter ................................ 3-24
Clutch lever ........................................... 3-20
Clutch lever free play, adjusting ............ 6-21
Coolant.................................................. 6-14
Coolant temperature warning light .......... 3-5
Cowlings and panels, removing and
installing................................................ 6-7DDimmer switch ...................................... 3-19
D-mode (drive mode) .............................. 3-1
Drive chain, cleaning and lubricating .... 6-25
Drive chain slack ................................... 6-24EEngine break-in ....................................... 5-3
Engine idling speed, checking .............. 6-17
Engine oil and oil filter cartridge ............ 6-11
Engine stop switch ................................ 3-19Engine trouble warning light ................... 3-8
FFront and rear brake pads, checking .... 6-22
Front fork, adjusting .............................. 3-28
Front fork, checking .............................. 6-28
Fuel....................................................... 3-22
Fuel consumption, tips for reducing........ 5-3
Fuel level warning light ........................... 3-5
Fuel tank breather/overflow hose ......... 3-24
Fuel tank cap ........................................ 3-22
Fuses, replacing ................................... 6-31HHandlebar switches .............................. 3-18
Hazard switch ....................................... 3-19
Headlight bulb, replacing ...................... 6-32
Helmet holder ....................................... 3-26
High beam indicator light ........................ 3-5
Horn switch ........................................... 3-19IIdentification numbers ............................ 9-1
Ignition circuit cut-off system ................ 3-34
Immobilizer system ................................. 3-1
Immobilizer system indicator light........... 3-8
Indicator and warning lights .................... 3-4KKey identification number ....................... 9-1LLicense plate light bulb, replacing ........ 6-34
Luggage strap holders .......................... 3-33MMain switch/steering lock........................ 3-3
Maintenance and lubrication, periodic .... 6-3
Maintenance, emission control system... 6-2
Matte color, caution ................................ 7-1Model label .............................................. 9-2
Multi-function meter unit .......................... 3-9
NNeutral indicator light .............................. 3-5OOil level warning light .............................. 3-5PParking .................................................... 5-4
Part locations .......................................... 2-1
Pass switch ........................................... 3-19RRear brake light switch, adjusting ......... 6-22
Rear view mirrors .................................. 3-28
Rider footrest position, adjusting ........... 3-27SSafety information ................................... 1-1
Seats ..................................................... 3-25
Shifting .................................................... 5-2
Shift pedal ............................................. 3-20
Shift timing indicator light ........................ 3-8
Shock absorber assembly, adjusting .... 3-30
Sidestand .............................................. 3-33
Sidestand, checking and lubricating...... 6-28
Spark plugs, checking ........................... 6-10
Specifications .......................................... 8-1
Starting the engine .................................. 5-1
Start switch............................................ 3-19
Steering, checking................................. 6-29
Steering damper warning light ................ 3-8
Storage.................................................... 7-4
Storage compartment............................ 3-27
Supporting the motorcycle .................... 6-35TTail/brake light ....................................... 6-33
U14BE0E0.book Page 1 Friday, November 21, 2008 9:23 AM