2009 YAMAHA YFZ450R air filter

8-25
1
2
3
4
5
6
78
9
10
11

8. Wash the sponge material gently but thor-
oughly in solvent.
WARNING

EWB01940
Always use parts cleaning solvent to clean the
sponge material. Never use low-flash-point
solvents or gasoline to clean the sponge mate-
rial because the engine could catch fire or ex-
plode.
9. Squeeze the excess solvent out of the sponge
material and let it dry.
NOTICE
ECB00440
Do not twist the sponge material when squeez-
ing it.
10. Check the sponge material and replace it if
damaged.
11. Apply a quality foam air filter oil to the sponge
material.TIP

The sponge material should be wet but not drip-
ping.
12. Pull the sponge material over the air filter ele-
ment frame.
1. Sponge material
2. Air filter element frame
1 2

8-26
1
2
3
4
5
6
78
9
10
11

13. Install the washer onto the air filter element
frame, and then insert the wing bolt into the
hole in the air filter element frame.
NOTICE

ECB00451
Be sure to install the washer with the bent edge
facing outward as shown.
14. Insert the air filter element into the air filter
case, and then tighten the wing bolt.
15. Install the air filter case cover by hooking the
holders onto the air filter case.
16. Install the seat.TIP
The air filter element should be cleaned every 20–
40 hours. It should be cleaned and lubricated more
often if the ATV is operated in extremely dusty ar-
eas. Each time the air filter element maintenance
is performed, check the air inlet of the air filter case
for obstructions. Check the air filter case rubber
joint to the throttle body and the rubber joint mani-
fold fittings for an air-tight seal. Tighten all fittings
securely to avoid the possibility of unfiltered air en-
tering the engine.NOTICE
ECB00760

Make sure that the air filter element is prop-
erly seated in the air filter case.

Never operate the engine with the air filter el-
ement removed. This will allow unfiltered air
to enter the engine, causing rapid engine
wear and possible engine damage. Addition-
ally, operation without the air filter element
will affect the fuel injection system with sub-
sequent poor performance and possible en-
gine overheating.
1. Washer
1

10-2
1
2
3
4
5
6
7
8
910
11

Recommended engine oil grade:
API service SG type or higher, JASO standard MA
Engine oil quantity:
Without oil filter element replacement:
1.40 L (1.48 US qt, 1.23 Imp.qt)
With oil filter element replacement:
1.45 L (1.53 US qt, 1.28 Imp.qt)
Cooling system:
Coolant reservoir capacity (up to the maximum level mark):
0.25 L (0.26 US qt, 0.22 Imp.qt)
Radiator capacity (including all routes):
1.25 L (1.32 US qt, 1.10 Imp.qt)
Air filter:
Air filter element:
Wet element
Fuel:
Recommended fuel:
Premium unleaded gasoline only
Fuel tank capacity:
10.0 L (2.64 US gal, 2.20 Imp.gal)
Fuel reserve amount:
3.4 L (0.90 US gal, 0.75 Imp.gal)
Fuel injection:
Throttle body:
Type/quantity:
42EHS/1
Spark plug (s):
Manufacturer/model:
NGK/CR8E
Spark plug gap:
0.7–0.8 mm (0.028–0.031 in)
Clutch:
Clutch type:
Wet, multiple-disc
Transmission:
Primary reduction system:
Spur gear
Primary reduction ratio:
61/23 (2.652)
Secondary reduction system:
Chain drive
Secondary reduction ratio:
38/14 (2.714)
Transmission type:
Constant mesh 5-speed
-20 -10 0
1020 304050 ˚C
SAE 15W-40
SAE 20W-40SAE 20W-50
SAE 10W-40
SAE 5W-30
SAE 10W-30

INDEX
A
Accessories and loading ................................................ 6-5
Air filter element, cleaning ............................................ 8-23
B
Battery .......................................................................... 8-43
Brake and clutch levers, checking and lubricating ....... 8-40
Brake fluid, changing.................................................... 8-32
Brake fluid level, checking............................................ 8-30
Brake lever ..................................................................... 4-6
Brake lever free play, checking the front ...................... 8-32
Brake light switches ..................................................... 8-35
Brake pads, checking the front and rear ...................... 8-29
Brake pedal .................................................................... 4-7
Brake pedal, checking and lubricating ......................... 8-41
Brake pedal position, checking .................................... 8-33
Brakes, front and rear .................................................... 5-4
C
Cables, checking and lubricating ................................. 8-40
Chassis fasteners........................................................... 5-8
Cleaning ......................................................................... 9-1
Clutch lever .................................................................... 4-6
Clutch lever free play, adjusting ................................... 8-36
Coolant ................................................................. 5-4
,
8-19
Coolant temperature warning light ................................. 4-2
D
Drive chain ..................................................................... 5-5Drive chain, lubricating ................................................. 8-39
Drive chain slack .......................................................... 8-37
E
Engine break-in .............................................................. 6-4
Engine oil ....................................................................... 5-4
Engine oil and oil filter element .................................... 8-14
Engine, start ................................................................... 6-1
Engine stop switch ......................................................... 4-3
Engine trouble warning light ........................................... 4-3
F
Fuel ........................................................................ 4-9
,
5-4
Fuel level warning light................................................... 4-2
Fuel tank cap.................................................................. 4-8
Fuse, replacing............................................................. 8-46
H
Handlebar position, adjusting ....................................... 4-24
Handlebar switches ........................................................ 4-3
Headlight beam, adjusting............................................ 8-48
Headlight bulb, replacing.............................................. 8-46
I
Identification numbers .................................................. 11-1
Indicator light and warning lights .................................... 4-2
Instruments, lights and switches .................................... 5-8
K
Key identification number ............................................. 11-1