2009 YAMAHA YFM90R checking oil

Cleaning the spark arrester ...................... 8-19
Adjusting the carburetor ........................... 8-20
Adjusting the engine idling speed ............ 8-20
Checking the throttle cable free play ....... 8-21
Timing chain ............................................ 8-22
Valve clearance ....................................... 8-22
Checking the front brake shoes................ 8-22
Adjusting the front brake lever free play ....................................................... 8-23
Checking the rear brake pads ................. 8-25
Checking the brake fluid level ................. 8-25
Changing the rear brake fluid .................. 8-26
Checking the rear brake lever free play ........................................................8-26
Checking and lubricating the cables........ 8-27
Checking and lubricating the front and rear brake levers............................... 8-27
Checking the wheel hub bearings ............ 8-28
Battery ..................................................... 8-28
Replacing the fuse ................................... 8-30
Removing a wheel ................................... 8-32
Installing a wheel ..................................... 8-33
Troubleshooting ....................................... 8-34
Troubleshooting chart .............................. 8-35
RIDING YOUR ATV ...................................... 7-1
GETTING TO KNOW YOUR ATV...............7-2
RIDE WITH CARE AND GOOD JUDGEMENT ............................................ 7-2
BE CAREFUL WHERE YOU RIDE...........7-11
TURNING YOUR ATV..............................7-15
CLIMBING UPHILL....................................7-17
RIDING DOWNHILL..................................7-20
CROSSING A SLOPE................................7-21
CROSSING THROUGH SHALLOW WATER ................................................... 7-22
RIDING OVER ROUGH TERRAIN...........7-24
SLIDING AND SKIDDING.........................7-25
WHAT TO DO IF.......................................7-26
WHAT TO DO... ........................................ 7-26
PERIODIC MAINTENANCE AND MINOR
REPAIR..........................................................8-1 Owner’s manual and tool kit ...................... 8-1
Periodic maintenance chart for the emission control system .......................... 8-3
General maintenance and lubrication chart ........................................................ 8-5

Checking the spark plug ............................. 8-9
Engine oil ................................................. 8-11
Final transmission oil ................................ 8-14
Cleaning the air filter element .................. 8-15 CLEANING AND STORAGE.........................9-1
Cleaning ..................................................... 9-1
Storage ...................................................... 9-2 Brakes ..................................................... 8-22

8-11
2. Clean the surface of the spark plug gasketand its mating surface, and then wipe off any
grime from the spark plug threads.
3. Install the spark plug with the spark plug wrench, and then tighten it to the specified
torque.TIPIf a torque wrench is not available when installing
a spark plug, a good estimate of the correct torque
is 1/4–1/2 turn past finger tight. However, the spark
plug should be tightened to the specified torque assoon as possible.
4. Install the spark plug cap. Engine oil The engine oil level should be checked before
each ride. In addition, the oil must be changed at
the intervals specified in the periodic maintenance
and lubrication chart. To check the engine oil level
1. Place the ATV on a level surface.
2. Check the engine oil level on a cold engine.
TIPIf the engine was started before checking the oil
level, be sure to warm up the engine sufficiently,
and then wait at least ten minutes until the oil set-1. Engine oil filler cap
2. Dipstick
12
tles for an accurate reading.
3. Remove the engine oil filler cap, and then wipe the dipstick off with a clean rag.
Tightening torque:
Spark plug:12.0 Nm (1.20 m·kgf, 8.9 ft·lbf)
8

8-13
8
7. Add the specified amount of the recommend-ed engine oil, and then install and tighten the
engine oil filler cap.
Tightening torque:
Engine oil drain bolt:8 Nm (0.8m·kgf, 5.8 ft·lbf)
Recommended oil: See page 10-1.
Oil quantity: 0.8 L (0.84 US qt) (0.70 Imp.qt)N O T I C EDo not mix any chemical additives. Do
not use oils with a diesel specification
of "CD" or oils of a higher quality than
sp eci fi ed . I n ad d i ti o n , d o n o t u se o i ls l ab el e d " E N E R G Y C O N S E R V I N G I I " o r
higher.the crankcase.
8. Start the engine, and then let it idle for severalMake sure that no foreign material enters minutes while checking it for oil leakage. If oil
is leaking, immediately turn the engine off and
check for the cause.
9. Turn the engine off, wait at least ten minutes, and then check the oil level and correct it if
necessary.

Changing the rear brake fluidChecking the rear brake lever free play
The brake lever free play must be checked at the
intervals specified in the periodic maintenance and
lubrication chart. The brake lever free play should
measure 0 – 1.5 mm (0 – 0.06 in) as shown. If
the free play is incorrect, have a Yamaha dealer
check the brake system.
1
LOWER
1
8-26
8
Recommended brake fluid:
DOT4
1. Brake lever free play
1. Minimum level mark
Have a Yamaha dealer change the rear brake fluid
at the intervals specified in the TIP after the periodic
maintenance and lubrication chart. In addition,
have the oil seals of the master cylinders and
calipers as well as the brake hoses replaced at the
intervals listed below or whenever they are damaged
or leaking.
Oil seals: Replace every two years.Brake hoses: Replace every four years.

8-27
Checking and lubricating the cables The operation and the condition of all control ca-
bles should be checked before each ride, and the
cables and cable ends should be lubricated if nec-
essary. If a cable is damaged or does not move
smoothly, have a Yamaha dealer check or replace
it.
Checking and lubricating the front and
rear brake levers The operation of the front and rear brake levers
should be checked before each ride, and the lever
pivots should be lubricated if necessary.Recommended lubricant:
Engine oil
8
WARNING
Operating with improperly serviced or adjust-
ed brakes could cause loss of braking ability,
which could lead to an accident.
After servicing:Make sure the brakes operate smoothly and
that the free play is correct.Make sure the brakes do not drag.Make sure the brakes are not spongy. All air
must be bled from the brake system.
Replacement of brake components requires
professional knowledge. These proceduresshould be performed by a Yamaha dealer.
WARNING
Inspect cables frequently and replace if dam-
aged. Corrosion can result when the cable
sheaths become damaged, and cables can
also become frayed or kinked, which could re-
strict the operation of controls and lead to anaccident or injury.

8-28
8
Checking the wheel hub bearings The front and rear wheel hub bearings must be
checked at the intervals specified in the periodic
maintenance and lubrication chart. If there is play
in a wheel hub or if a wheel does not turn smoothly,
have a Yamaha dealer check the wheel hub bearings.1. Lever pivot
BatteryT h i s m o d e l i s e q u i p p e d w i t h a V R L A ( V a l v e
Regulated Lead Acid) battery. There is no need to
check the electrolyte or to add distilled water.
However, the battery lead connections need to be
checked and, if necessary, tightened.
Recommended lubricant:Front brake lever: Lithium-soap-based grease
N O T I C E Never attempt to remove the battery cell seals,
as this would permanently damage the battery.
1
WARNING
Battery electrolyte is poisonous and danger-
ous, as it contains sulfuric acid, which can
cause severe burns. Avoid contact with skin,
eyes or clothing. Always shield your eyes
when working near batteries.
Antidote:
EXTERNAL: Flush with water.
INTERNAL: Drink large quantities of water or
milk. Follow with milk of magnesia, beaten egg
or vegetable oil. Call a physician immediately.
Rear brake lever:
Silicone grease

INDEX
AAccessories and loading ................................................ 6-6
Air filter element, cleaning ............................................ 8-15BBattery ........................................................................\
...8-28
Brake lever, front.............................................................4-6Brake lever, rear............................................................4-6
Brake lever free play, checking the rear........................8-26
Brake levers, checking and lubricating .............. .......... 8-27
Brakes, front and rear....................................................5-3
Brake pads, checking the rear.......................................8-25
Brake fluid level, checking the rear...............................8-25
Brake fluid level, changing the rear..............................8-26 Brake lever free play, adjusting the front......................8-23CCables, checking and lubricating ................................. 8-27
Carburetor, adjusting.................................................... 8-20
Chassis fasteners........................................................... 5-7
Cleaning..........................................................................9-1EEngine break-in .............................................................. 6-4
Engine, cold start...........................................................6-1
Engine idling speed ...................................................... 8-20 Engine oil............................................................5-3, 8-11
Engine, starting a warm................................................6-3
Engine stop switch.......................................................4-2
Fuel........................................................................4-8, 5-3
Fuel cock......................................................................4-10
Fuel tank cap..................................................................4-8
Fuse, replacing.............................................................8-30
F
KKey identification number ............................................. 11-1LLabel locations...............................................................2-1HHandlebar switches ........................................................ 4-2IIdentification numbers .................................................. 11-1
Instruments and switches.............................................5-7MMain switch .................................................................... 4-1
Maintenance and lubrication chart.................................8-5
Maintenance chart, emission control system.................8-3
Model label...................................................................11-2
Choke ............................................................................ 4-11 Brake shoes, checking the front .................................. 8-22
Final transmission oil ........................................... 5-3, 8-14
Engine speed limiter plate............................................ 4-5
Kick starter ................................................................. 4-12