2009 YAMAHA YFM350R-W torque

4-17
4
CAUTION:ECB00090Never turn an adjusting mechanism beyondthe minimum and maximum settings.3. Tighten the locknut to the specified torque.
CAUTION:ECB00080Always tighten the locknut against the adjust-
ing nut, and then tighten it to the specifiedtorque.
1. Special wrenchSpring preload setting:
Minimum (hard):
Distance A = 218.5 mm (8.6 in)
Standard:
Distance A = 228.5 mm (9.0 in)
Maximum (soft):
Distance A = 233.5 mm (9.2 in)
1. Distance ATightening torque:
Locknut:
42 Nm (4.2 m·kgf, 30 ft·lbf)
1
U10P60E0.book Page 17 Thursday, June 15, 2006 4:19 PM

8-2
8The service information included in this manual
and the tools provided in the owner’s tool kit are in-
tended to assist you in the performance of preven-
tive maintenance and minor repairs. However,
additional tools such as a torque wrench may be
necessary to perform certain maintenance work
correctly.
NOTE:If you do not have the tools or experience required
for a particular job, have a Yamaha dealer performit for you.
WARNING
EWB01850Never modify this ATV through improper in-
stallation or use of accessories, as it may
cause changes in handling, which in some sit-
uations could lead to an accident. All parts and
accessories added to this ATV should be gen-
uine Yamaha or equivalent components de-
signed for use on this ATV and should be
installed and used according to instructions. If
you have questions, consult an authorizedYamaha ATV dealer.U10P60E0.book Page 2 Thursday, June 15, 2006 4:19 PM

8-9
8 2. Check the spark plug for electrode erosion
and excessive carbon or other deposits, and
replace it if necessary.
To install the spark plug
1. Measure the spark plug gap with a wire thick-
ness gauge and, if necessary, adjust the gap
to specification.
2. Clean the surface of the spark plug gasket
and its mating surface, and then wipe off any
grime from the spark plug threads.
3. Install the spark plug with the spark plug
wrench, and then tighten it to the specified
torque. Specified spark plug:
NGK/DR8EA
Spark plug gap:
0.6–0.7 mm (0.024–0.028 in)
1. Spark plug gapTightening torque:
Spark plug:
17.5 Nm (1.75 m·kgf, 12.7 ft·lbf)
U10P60E0.book Page 9 Thursday, June 15, 2006 4:19 PM

8-10
8
NOTE:If a torque wrench is not available when installing
a spark plug, a good estimate of the correct torque
is 1/4–1/2 turn past finger tight. However, the spark
plug should be tightened to the specified torque assoon as possible.
4. Install the spark plug cap.EBU23273Engine oil and oil filter element The engine oil level should be checked before
each ride. In addition, the oil must be changed and
the oil filter element cleaned at the intervals speci-
fied in the periodic maintenance and lubrication
chart.
To check the engine oil level
1. Place the ATV on a level surface.
2. Start the engine, warm it up for several min-
utes, and then turn it off.
3. Wait a few minutes until the oil settles before
checking.
4. Remove the engine oil filler cap, and then
wipe the dipstick off with a clean rag.5. Insert the dipstick into the filler hole (without
screwing it in), and then remove it again to
check the oil level.
NOTE:The engine oil should be between the minimumand maximum level marks.
6. If the engine oil is at or below the minimum
level mark, add sufficient oil of the recom-
mended type to raise it to the correct level.1. Dipstick
2. Maximum level mark
3. Minimum level mark
4. Engine oil filler cap
U10P60E0.book Page 10 Thursday, June 15, 2006 4:19 PM

8-12
85. Remove the oil filter element cover by remov-
ing the bolts, and then remove the oil filter el-
ement.
6. Clean the oil strainer and oil filter element with
solvent.
7. Check the O-rings for damage and replace it if
necessary.
8. Install the oil filter element and O-ring.
NOTE:Make sure that the O-ring is properly seated.9. Install the oil filter element cover by installing
the bolts, and then tighten them to the speci-
fied torque.
10. Install the oil strainer, compression spring, O-
ring and engine oil drain bolt. Tighten the en-
gine oil drain bolt to the specified torque.
CAUTION:ECB00320Before installing the engine oil drain bolt, be
sure to install the O-ring, compression springand oil strainer.
11. Add the specified amount of the recommend-
ed engine oil, and then install and tighten the
engine oil filler cap.
1. Oil filter element cover
2. Bolt
3. Oil filter element
4. O-ring
Tightening torque:
Oil filter element cover bolt:
10 Nm (1.0 m·kgf, 7.2 ft·lbf)
Tightening torque:
Engine oil drain bolt:
32 Nm (3.2 m·kgf, 23 ft·lbf)
U10P60E0.book Page 12 Thursday, June 15, 2006 4:19 PM

8-25
8
NOTE:If the cable length cannot be adjusted to specifica-tion, consult a Yamaha dealer.
5. Tighten the locknut on the brake cable.
6. Turn in the adjusting bolt at the rear brake cal-
iper until it feels tight, then turn it out 1/8 turn
and tighten its locknut to the specified torque.CAUTION:ECB00520When tightening the locknut, hold the adjust-
ing bolt with a wrench so that it does not turntogether with the locknut.
WARNING
EWB02090Operating with improperly serviced or adjust-
ed brakes could cause the brakes to malfunc-
tion, resulting in reduced braking
performance. This could increase the chance
of a collision or accident. After adjusting the
parking brake free play, block the rear of the
ATV off the ground and spin the rear wheels.
Check to make sure there is no brake drag. If
brake drag is noticed, perform the adjustmentagain.EBU24740Brake light switches The operation of the brake light switches must be
checked and, if necessary, adjusted at the inter-
vals specified in the periodic maintenance and lu-
brication chart.
The brake light switch for the brake pedal can be
adjusted as follows, but the other brake light
switches should be adjusted by a Yamaha dealer.
1. Locknut
2. Adjusting nut
Tightening torque:
Locknut (rear brake caliper):
16 Nm (1.6 m·kgf, 11 ft·lbf)
U10P60E0.book Page 25 Thursday, June 15, 2006 4:19 PM

8-29
8 mark on both drive chain pullers with the alignment
mark on either side of the swingarm for proper
wheel alignment.CAUTION:ECB00541Improper drive chain slack will overload the en-
gine as well as other vital parts of the ATV and
can lead to drive chain slippage or breakage.
To prevent this from occurring, keep the drivechain slack within the specified limits.3. Tighten the locknuts and the axle holding nuts
to the specified torques.
NOTE:Make sure that the curved edge of the speed sen-
sor bracket touches the rear wheel hub when tight-ening the axle holding nuts.
1. Locknut
2. Drive chain slack adjusting bolt
3. Alignment marks
1. Speed sensor bracket
2. Rear wheel hub
3. Curved edge
U10P60E0.book Page 29 Thursday, June 15, 2006 4:19 PM

8-30
8
EBU24880Lubricating the drive chain The drive chain must be cleaned and lubricated at
the intervals specified in the periodic maintenance
and lubrication chart, otherwise it will quickly wear
out, especially when riding in dusty or wet areas.
Service the drive chain as follows.
CAUTION:ECB00560The drive chain must be lubricated after wash-ing the ATV or riding in the rain.
1. Clean the drive chain with kerosene and a
small soft brush.CAUTION:ECB00570To prevent damaging the O-rings, do not clean
the drive chain with steam cleaners, high-pres-sure washers or inappropriate solvents.
2. Wipe the drive chain dry.
3. Thoroughly lubricate the drive chain with a
special O-ring chain lubricant.CAUTION:ECB00580Do not use engine oil or any other lubricants
for the drive chain, as they may contain sub-stances that could damage the O-rings.EBU24900Checking and lubricating the cables The operation and the condition of all control ca-
bles should be checked before each ride, and the
cables and cable ends should be lubricated if nec- Tightening torques:
Locknut:
16 Nm (1.6 m·kgf, 11 ft·lbf)
Axle holding nut (upper):
120 Nm (12.0 m·kgf, 85 ft·lbf)
Axle holding nut (lower):
73 Nm (7.3 m·kgf, 53 ft·lbf)
1. O-ringU10P60E0.book Page 30 Thursday, June 15, 2006 4:19 PM