2009 YAMAHA WOLVERINE 450 oil level

8-23
83. If the oil is below the brim of the filler hole, add
sufficient oil of the recommended type to raise
it to the correct level.
4. Install the oil filler bolt, and then tighten it to the
specified torque.
To change the final gear oil
1. Place the ATV on a level surface.2. Remove the final gear case guard by remov-
ing the bolts.
3. Place an oil pan under the final gear case to
collect the used oil.
4. Remove the final gear oil filler bolt and the fi-
nal gear oil drain bolt to drain the oil from the
final gear case.
1. Final gear oil
2. Final gear oil filler bolt
3. Correct oil levelTightening torque:
Final gear oil filler bolt:
23 Nm (2.3 m·kgf, 17 ft·lbf)
1. Final gear case guard
2. Bolt
U3C263E0.book Page 23 Thursday, May 15, 2008 10:44 AM

8-24
8 5. Install the drain bolt, and then tighten it to the
specified torque.
6. Refill with the recommended final gear oil to
the brim of the filler hole as shown.
NOTICEECB00420Be sure no foreign material enters the finalgear case.
7. Install the oil filler bolt, and then tighten it to the
specified torque.
1. Final gear oil drain boltTightening torque:
Final gear oil drain bolt:
23 Nm (2.3 m·kgf, 17 ft·lbf)
1. Final gear oil
2. Final gear oil filler bolt
3. Correct oil levelRecommended final gear oil:
See page 10-1.
U3C263E0.book Page 24 Thursday, May 15, 2008 10:44 AM

8-25
88. Check the final gear case for oil leakage. If oil
is leaking, check for the cause.
9. Install the final gear case guard by installing
the bolts and tightening them to the specified
torque.
EBU23433Changing the differential gear oil The differential gear case must be checked for oil
leakage before each ride. If any leakage is found,
have a Yamaha dealer check and repair the ATV.
In addition, the differential gear oil must be
changed as follows at the intervals specified in the
periodic maintenance and lubrication chart.
1. Place the ATV on a level surface.
2. Place an oil pan under the differential gear
case to collect the used oil.3. Remove the differential gear oil filler bolt and
the differential gear oil drain bolt to drain the
oil from the differential gear case. Tightening torque:
Final gear oil filler bolt:
23 Nm (2.3 m·kgf, 17 ft·lbf)
Tightening torque:
Final gear case guard bolt:
16 Nm (1.6 m·kgf, 11 ft·lbf)
1. Differential gear oil filler bolt
U3C263E0.book Page 25 Thursday, May 15, 2008 10:44 AM

8-26
8 4. Install the drain bolt, and then tighten it to the
specified torque.
5. Refill with the specified amount of the recom-
mended differential gear oil.
TIP
Do not exceed the specified differential gear oil
quantity when filling. Overfilling will cause the oil
to seep out of the breather hose during and after
riding.

The differential gear case capacity is greater
than the recommended oil quantity, therefore
the oil level cannot be accurately checked fromthe oil filler hole.NOTICEECB00410Be sure no foreign material enters the differen-tial gear case.
6. Install the oil filler bolt, and then tighten it to the
specified torque.
7. Check the differential gear case for oil leak-
age. If oil is leaking, check for the cause.
1. Differential gear oil drain boltTightening torque:
Differential gear oil drain bolt:
10 Nm (1.0 m·kgf, 7.2 ft·lbf)
Recommended differential gear oil:
See page 10-1.
Oil quantity:
0.35 L (0.37 US qt, 0.31 Imp.qt)
Tightening torque:
Differential gear oil filler bolt:
23 Nm (2.3 m·kgf, 17 ft·lbf)
U3C263E0.book Page 26 Thursday, May 15, 2008 10:44 AM

8-41
8Rear brake
TIPTo check the rear brake fluid level, remove cowlingB. (See page 8-9.)
Observe these precautions:
When checking the fluid level, make sure that
the top of the brake fluid reservoir is level.
Use only the recommended quality brake fluid,
otherwise the rubber seals may deteriorate,
causing leakage and poor braking performance.

Refill with the same type of brake fluid. Mixing
fluids may result in a harmful chemical reaction
and lead to poor braking performance.
Be careful that water does not enter the brake
fluid reservoir when refilling. Water will signifi-
cantly lower the boiling point of the fluid and may
result in vapor lock.
Brake fluid may deteriorate painted surfaces or
plastic parts. Always clean up spilled fluid imme-
diately.
As the brake pads wear, it is normal for the brake
fluid level to gradually go down. However, if the
brake fluid level goes down suddenly, have a
Yamaha dealer check the cause.EBU24291Changing the brake fluid Have a Yamaha dealer change the brake fluid at
the intervals specified in the TIP after the periodic
maintenance and lubrication chart. In addition,
have the oil seals of the master cylinders and cali-
pers as well as the brake hoses replaced at the in-
tervals listed below or whenever they are damaged
or leaking.
Oil seals: Replace every two years.
Brake hoses: Replace every four years.
1. Minimum level markRecommended brake fluid:
DOT 4
U3C263E0.book Page 41 Thursday, May 15, 2008 10:44 AM

10-1
10
EBU25960
SPECIFICATIONS
Dimensions:Overall length:
1978 mm (77.9 in)
Overall width:
1063 mm (41.9 in)
Overall height:
1095 mm (43.1 in)
Seat height:
840 mm (33.1 in)
Wheelbase:
1233 mm (48.5 in)
Ground clearance:
220 mm (8.7 in)
Minimum turning radius:
3000 mm (118 in)Weight:With oil and fuel:
250.0 kg (551 lb)Noise and vibration level:Noise level (77/311/EEC):
80.8 dB(A)
Vibration on seat (EN1032, ISO5008):
Will not exceed 0.7 m/s²
Vibration on handlebar (EN1032, ISO5008):
Will not exceed 2.5 m/s²Engine:Engine type:
Liquid cooled 4-stroke, SOHCCylinder arrangement:
Forward-inclined single cylinder
Displacement:
421.0 cm³
Bore × stroke:
84.5 × 75.0 mm (3.33 × 2.95 in)
Compression ratio:
10.00 :1
Starting system:
Electric starter
Lubrication system:
Wet sump
U3C263E0.book Page 1 Thursday, May 15, 2008 10:44 AM

10-2
10
Engine oil:Type:
SAE 5W-30 or SAE 10W-30 or SAE 10W-40 or SAE
15W-40 or SAE 20W-40 or SAE 20W-50
Recommended engine oil grade:
API service SG type or higher, JASO standard MA
Engine oil quantity:
Without oil filter cartridge replacement:
2.30 L (2.43 US qt, 2.02 Imp.qt)
With oil filter cartridge replacement:
2.40 L (2.54 US qt, 2.11 Imp.qt)Final gear oil:Type:
SAE 80 API GL-4 Hypoid gear oil
Quantity:
0.23 L (0.24 US qt, 0.20 Imp.qt)
Differential gear oil:Type:
SAE 80 API GL-4 Hypoid gear oil
Quantity:
0.35 L (0.37 US qt, 0.31 Imp.qt)Cooling system:Coolant reservoir capacity (up to the maximum level mark):
0.25 L (0.26 US qt, 0.22 Imp.qt)
Radiator capacity (including all routes):
1.32 L (1.40 US qt, 1.16 Imp.qt)Air filter:Air filter element:
Wet elementFuel:Recommended fuel:
Regular unleaded gasoline only
Fuel tank capacity:
14.5 L (3.83 US gal, 3.19 Imp.gal)
Fuel reserve amount:
4.5 L (1.19 US gal, 0.99 Imp.gal)Carburetor:Manufacturer:
MIKUNI
Type × quantity:
BSR33 x 1Spark plug (s):Manufacturer/model:
NGK/DR8EA
Spark plug gap:
0.6–0.7 mm (0.024–0.028 in)
-20 -10 0
1020 304050 ˚C
SAE 15W-40
SAE 20W-40SAE 20W-50
SAE 10W-40
SAE 5W-30
SAE 10W-30
U3C263E0.book Page 2 Thursday, May 15, 2008 10:44 AM

INDEX
AAccessories and loading ................................................ 6-6
Air filter element, cleaning ............................................ 8-31
Axle boots .................................................................... 8-44BBattery .......................................................................... 8-47
Brake fluid, changing .................................................... 8-41
Brake fluid level, checking ............................................ 8-40
Brake lever free play and brake pedal position (rear),
adjusting and checking .............................................. 8-42
Brake lever free play, checking the front ...................... 8-42
Brake lever, front ............................................................ 4-8
Brake levers, checking and lubricating ......................... 8-46
Brake light switches ..................................................... 8-45
Brake pads, checking the front and rear ...................... 8-39
Brake pedal and rear brake lever ................................... 4-8
Brake pedal, checking and lubricating ......................... 8-46
Brakes, front and rear .................................................... 5-4CCables, checking and lubricating ................................. 8-45
Carburetor, adjusting .................................................... 8-36
Chassis fasteners ........................................................... 5-7
Cleaning ......................................................................... 9-1
Coolant .................................................................. 5-3, 8-27
Coolant temperature warning light ................................. 4-2
Cowlings and panels, removing and installing ............... 8-9DDifferential gear oil ......................................................... 5-3Differential gear oil, changing ....................................... 8-25
Drive select lever ............................................................ 4-9
Drive select lever and driving in reverse ........................ 6-3
Drive select lever safety system cable, adjusting ......... 8-39
EEngine break-in .............................................................. 6-5
Engine, cold start ........................................................... 6-1
Engine idling speed ...................................................... 8-36
Engine oil ....................................................................... 5-3
Engine oil and oil filter cartridge ................................... 8-17
Engine, starting a warm ................................................. 6-3
Engine stop switch ......................................................... 4-4FFinal gear oil .......................................................... 5-3, 8-22
Four-wheel-drive indicator .............................................. 4-3
Fuel ......................................................................... 4-9, 5-3
Fuel cock ...................................................................... 4-10
Fuel tank cap .................................................................. 4-9
Fuses, replacing ........................................................... 8-50HHandlebar switches ........................................................ 4-4
Headlight beam, adjusting ............................................ 8-53
Headlight bulb, replacing .............................................. 8-51IIdentification numbers .................................................. 11-1
Indicator lights and warning light .................................... 4-2
Instruments, lights and switches .................................... 5-7
U3C263E0.book Page 1 Thursday, May 15, 2008 10:44 AM