2009 YAMAHA VMAX coolant

PERIODIC MAINTENANCE AND ADJUSTMENT
6-4
1
2
3
4
5
6
7
8
9

21

*
Shock absorber
assembly

Check operation and shock
absorber for oil leakage.
√√√√
22

*
Rear suspension
relay arm and con-
necting arm pivoting
points

Check operation.
√√√√
23

*
Fuel injection sys-
tem

Adjust synchronization.
√√√√√
24

Engine oil

Change.

Check oil level and vehicle for oil
leakage.
√√√√√√
25

Engine oil filter car-
tridge

Replace.
√√√
26

*
Cooling system

Check coolant level and vehicle
for coolant leakage.
√√√√√

Change. Every 3 years
27

Final gear oil

Check oil level and vehicle for oil
leakage.
√√ √

Change.
√√√
28

*
Front and rear brake
switches

Check operation.
√√√√√√
29

Moving parts and
cables

Lubricate.
√√√√√
30

*
Throttle grip hous-
ing and cable

Check operation and free play.

Adjust the throttle cable free play
if necessary.

Lubricate the throttle grip housing
and cable.
√√√√√
NO. ITEM CHECK OR MAINTENANCE JOBODOMETER READING
ANNUAL
CHECK 1000 km
(600 mi)10000 km
(6000 mi)20000 km
(12000 mi)30000 km
(18000 mi)40000 km
(24000 mi)

PERIODIC MAINTENANCE AND ADJUSTMENT
6-14
1
2
3
4
5
6
7
8
9

EAU20070
Coolant
The coolant level should be checked
before each ride. In addition, the cool-
ant must be changed at the intervals
specified in the periodic maintenance
and lubrication chart.
EAU46690
To check the coolant level
1. Place the vehicle on a level sur-
face and hold it in an upright posi-
tion.
TIP


The coolant level must be checked
on a cold engine since the level
varies with engine temperature.

Make sure that the vehicle is posi-
tioned straight up when checking
the coolant level. A slight tilt to the
side can result in a false reading.
2. Check the coolant level in the cool-
ant reservoir.
TIP

The coolant should be between the
minimum and maximum level marks.3. If the coolant is at or below the
minimum level mark, remove the
coolant reservoir cap guard by re-
moving the bolt, and then remove
the reservoir cap.
4. Add coolant to the maximum level
mark, and then install the reservoir
cap.
WARNING! Remove only
the coolant reservoir cap. Never
attempt to remove the radiator
cap when the engine is
hot.
[EWA15161]

NOTICE:
If coolant is
not available, use distilled wateror soft tap water instead. Do not
use hard water or salt water
since it is harmful to the engine.
If water has been used instead
of coolant, replace it with cool-
ant as soon as possible, other-
wise the cooling system will not
be protected against frost and
corrosion. If water has been
added to the coolant, have a
Yamaha dealer check the anti-
freeze content of the coolant as
soon as possible, otherwise the
effectiveness of the coolant will
be reduced.
[ECA10472]

5. Install the coolant reservoir cap
guard by installing the bolt.
EAU46422
To change the coolant
1. Place the vehicle on a level sur-
face and let the engine cool if nec-
essary.
2. Remove cowling A. (See
page 6-6.)
1. Coolant reservoir cap
2. Coolant reservoir cap guard
3. Bolt
4. Maximum level mark
5. Minimum level mark2
1
5 4
3

Coolant reservoir capacity (up to the
maximum level mark):
0.27 L (0.29 US qt, 0.24 Imp.qt)

PERIODIC MAINTENANCE AND ADJUSTMENT
6-15
2
3
4
5
67
8
9
3. Remove the air intake duct by re-
moving the bolts.
4. Place a container under the engine
to collect the used coolant.
5. Remove the radiator cap.
WARNING! Never attempt to re-
move the radiator cap when the
engine is hot.

[EWA10381]
6. Remove the coolant reservoir cov-
er and coolant reservoir by remov-
ing the bolts.
7. Remove the coolant reservoir cap
guard by removing the bolt, and
then remove the reservoir cap.
8. Drain the coolant from the coolant
reservoir by turning it upside down.
9. Install the coolant reservoir cover
and the coolant reservoir by plac-
ing them in their original position,
and then installing the bolts.
10. Remove the coolant drain bolt to
drain the cooling system.
1. Bolt
2. Air intake duct
11
2

1. Radiator cap
1

1. Bolt
2. Coolant reservoir cap
3. Coolant reservoir cap guard
4. Bolt
5. Coolant reservoir cover
6. Coolant reservoir
5
6
1
2
3
4

PERIODIC MAINTENANCE AND ADJUSTMENT
6-16
1
2
3
4
5
6
7
8
9
11. After the coolant is completely
drained, thoroughly flush the cool-
ing system with clean tap water.
12. Install the coolant drain bolt.
TIP

Check the O-ring for damage and re-
place it if necessary.
13. Hold the vehicle upright, and pour
the specified amount of the recom-
mended coolant into the radiator
and reservoir.
NOTICE:
Failing to
hold the vehicle upright when
filling the radiator with coolant
may cause air to be trapped in
the cooling system.
[ECA16540]
14. Install the coolant reservoir cap,
and then install the reservoir cap
guard by installing the bolt.
15. Install the radiator cap.
16. Start the engine, let it idle for sev-
eral minutes, and then turn it off.
17. Remove the radiator cap to check
the coolant level in the radiator. If
necessary, add sufficient coolant
until it reaches the top of the radia-
tor, and then install the radiator
cap.
18. Check the coolant level in the res-
ervoir. If necessary, remove the
coolant reservoir cap guard and
the cap, add coolant to the maxi-mum level mark, and then install
the cap and the cap guard.
19. Start the engine, and then check
the vehicle for coolant leakage. If
coolant is leaking, have a Yamaha
dealer check the cooling system.
20. Install the air intake duct by install-
ing the bolts.
21. Install the cowling.
1. Coolant drain bolt
1

Antifreeze/water mixture ratio:
1:1
Recommended antifreeze:
High-quality ethylene glycol anti-
freeze containing corrosion inhibitors
for aluminum engines
Coolant quantity:
Radiator capacity (including all
routes):
3.75 L (3.96 US qt, 3.30 Imp.qt)
Coolant reservoir capacity (up to the
maximum level mark):
0.27 L (0.29 US qt, 0.24 Imp.qt)

PERIODIC MAINTENANCE AND ADJUSTMENT
6-39
2
3
4
5
67
8
9 Engine overheating
WARNING

EWAT1040

Do not remove the radiator cap when the engine and radiator are hot. Scalding hot fluid and steam may be
blown out under pressure, which could cause serious injury. Be sure to wait until the engine has cooled.

Place a thick rag, like a towel, over the radiator cap, and then slowly rotate the cap counterclockwise to the de-
tent to allow any residual pressure to escape. When the hissing sound has stopped, press down on the cap
while turning it counterclockwise, and then remove the cap.
TIP

If coolant is not available, tap water can be temporarily used instead, provided that it is changed to the recommended coolant
as soon as possible.
Wait until the
engine has cooled.
Check the coolant level in the
reservoir and radiator.
The coolant level
is OK.The coolant level is low.
Check the cooling system
for leakage.
Have a Yamaha dealer checkand repair the cooling system.Add coolant. (See TIP.)
Start the engine. If the engine overheats again,
have a
Yamaha dealer check
and repair the cooling system.
There is
leakage.
There is
no leakage.

8-1
1
2
3
4
5
6
7
8
9

SPECIFICATIONS
EAU2633P
Dimensions:
Overall length:
2395 mm (94.3 in)
Overall width:
820 mm (32.3 in)
Overall height:
1190 mm (46.9 in)
Seat height:
775 mm (30.5 in)
Wheelbase:
1700 mm (66.9 in)
Ground clearance:
140 mm (5.51 in)
Minimum turning radius:
3500 mm (137.8 in)
Weight:
With oil and fuel:
310.0 kg (683 lb)
Engine:
Engine type:
Liquid cooled 4-stroke, DOHC
Cylinder arrangement:
V-type 4-cylinder
Displacement:
1679.0 cm
3

Bore
×
stroke:
90.0
×
66.0 mm (3.54
×
2.60 in)
Compression ratio:
11.30 :1
Starting system:
Electric starterLubrication system:
Wet sump

Engine oil:
Type:
SAE 10W-40, SAE 10W-50, SAE 15W-40,
SAE 20W-40 or SAE 20W-50
Recommended engine oil grade:
API service SG type or higher, JASO stan-
dard MA
Engine oil quantity:
Without oil filter cartridge replacement:
4.30 L (4.55 US qt, 3.78 Imp.qt)
With oil filter cartridge replacement:
4.70 L (4.97 US qt, 4.14 Imp.qt)
Final gear oil:
Type:
Shaft drive gear oil (Part No.:
9079E-SH001-00)
Quantity:
0.30 L (0.32 US qt, 0.26 Imp.qt)
Cooling system:
Coolant reservoir capacity (up to the maxi-
mum level mark):
0.27 L (0.29 US qt, 0.24 Imp.qt)
Radiator capacity (including all routes):
3.75 L (3.96 US qt, 3.30 Imp.qt)
Air filter:
Air filter element:
Oil-coated paper element
Fuel:
Recommended fuel:
Premium unleaded gasoline only
Fuel tank capacity:
15.0 L (3.96 US gal, 3.30 Imp.gal)
Fuel reserve amount:
3.9 L (1.03 US gal, 0.86 Imp.gal)
Fuel injection:
Throttle body:
Manufacturer:
MIKUNI
Type/quantity:
EIS48/4
Spark plug (s):
Manufacturer/model:
NGK/CR9EIA
Manufacturer/model:
DENSO/IU27D
Spark plug gap:
0.8–0.9 mm (0.031–0.035 in)
Clutch:
Clutch type:
Wet, multiple-disc
-20 -10 0
10 20 30
40
50 ˚C
SAE 10W-30
SAE 15W-40SAE 20W-40SAE 20W-50
SAE 10W-40SAE 10W-50

SPECIFICATIONS
8-3
1
2
3
4
5
6
7
8
9Front suspension:

Type:
Telescopic fork
Spring/shock absorber type:
Coil spring/oil damper
Wheel travel:
120.0 mm (4.72 in)
Rear suspension:
Type:
Swingarm (link suspension)
Spring/shock absorber type:
Coil spring/gas-oil damper
Wheel travel:
110.0 mm (4.33 in)
Electrical system:
Ignition system:
TCI (digital)
Charging system:
AC magneto
Battery:
Model:
YTZ14S
Voltage, capacity:
12 V, 11.2 Ah
Headlight:
Bulb type:
Halogen bulb
Bulb voltage, wattage
×
quantity:
Headlight:
12 V, 60 W/55.0 W
×
1
Tail/brake light:
LEDFront turn signal light:
12 V, 10.0 W
×
2
Rear turn signal light:
12 V, 10.0 W
×
2
Auxiliary light:
12 V, 5.0 W
×
1
Meter lighting:
LED
Neutral indicator light:
LED
High beam indicator light:
LED
Oil level warning light:
LED
Turn signal indicator light:
LED x 2
Fuel level warning light:
LED
Coolant temperature warning light:
LED
Engine trouble warning light:
LED
ABS warning light:
LED
Immobilizer system indicator light:
LED

Fuses:
Main fuse:
50.0 A
Headlight fuse:
15.0 A
Signaling system fuse:
7.5 AIgnition fuse:
20.0 A
Parking lighting fuse:
7.5 A
Radiator fan fuse:
20.0 A
Fuel injection system fuse:
15.0 A
ABS control unit fuse:
7.5 A
ABS motor fuse:
30.0 A
ABS solenoid fuse:
15.0 A
Backup fuse:
7.5 A
Electronic throttle valve fuse:
7.5 A

INDEX
A
ABS ......................................................... 3-18
ABS warning light ...................................... 3-5
Air filter element....................................... 6-17
Anti-theft alarm (optional) ........................ 3-14
Auxiliary light bulb, replacing ................... 6-36
B
Battery ..................................................... 6-28
Brake and clutch fluids, changing ............ 6-24
Brake and clutch levers, checking and
lubricating .............................................. 6-25
Brake fluid level, checking ....................... 6-23
Brake lever .............................................. 3-17
Brake pedal ............................................. 3-18
Brake pedal, checking and lubricating ..... 6-25
C
Cables, checking and lubricating ............. 6-24
Care ........................................................... 7-1
Catalytic converters ................................. 3-22
Clutch lever.................................... 3-16
,
6-21
Coolant .................................................... 6-14
Coolant temperature warning light............. 3-4
Cowling and panels, removing and
installing .................................................. 6-6
D
Dimmer switch ......................................... 3-15
E
Engine break-in ......................................... 5-3
Engine idling speed, checking ................. 6-17
Engine oil and oil filter cartridge ................ 6-9
Engine stop switch................................... 3-15
Engine trouble warning light ...................... 3-4
EXUP system .......................................... 3-28
F
Final gear oil ............................................ 6-12
Front and rear brake pads, checking....... 6-22
Front brake lever free play, checking ...... 6-21
Front fork, adjusting................................. 3-24
Front fork, checking ................................. 6-26
Fuel ......................................................... 3-20
Fuel level warning light .............................. 3-4
Fuel tank cap ........................................... 3-19
Fuses, replacing ...................................... 6-31
H
Handlebar switches ................................. 3-15
Hazard switch .......................................... 3-16
Headlight bulb, replacing ......................... 6-32
High beam indicator light ........................... 3-3
Horn switch.............................................. 3-15
I
Identification numbers ............................... 9-1
Ignition circuit cut-off system ................... 3-29
Immobilizer system.................................... 3-1
Immobilizer system indicator light ............. 3-5
Indicator and warning lights....................... 3-3
K
Key identification number .......................... 9-1
L
License plate light bulb, replacing ........... 6-35
Luggage strap holders............................. 3-28
M
Main switch/steering lock .......................... 3-2
Matte color, caution ................................... 7-1
Model label ................................................ 9-2
Multi-function display ................................. 3-6
N
Neutral indicator light................................. 3-3
O
Oil level warning light ................................ 3-3
P
Parking ...................................................... 5-3
Part locations ............................................ 2-1
Pass switch ............................................. 3-15
Periodic maintenance and lubrication
chart ........................................................ 6-2
R
Rear brake light switch, adjusting ........... 6-22
S
Safety information ..................................... 1-1
Seats ....................................................... 3-22
Shifting ...................................................... 5-2
Shift pedal ............................................... 3-17
Shift pedal, checking and lubricating ...... 6-26
Shock absorber assembly, adjusting ...... 3-26
Sidestand ................................................ 3-29
Sidestand, checking and lubricating ....... 6-26
Spark plugs, checking ............................... 6-8
Specifications ............................................ 8-1
Speedometer unit...................................... 3-5
Starting the engine .................................... 5-1
Start switch ............................................. 3-15
Steering, checking .................................. 6-27
Storage ..................................................... 7-4
Supporting the motorcycle ...................... 6-36
T
Tail/brake light......................................... 6-34
Throttle cable free play, checking ........... 6-17
Throttle grip and cable, checking and
lubricating ............................................. 6-24
Tires ........................................................ 6-18
Tool kit ...................................................... 6-1