Maintenance and care
45
EJU33480
Storage
WARNING
EWJ00320
Always turn the fuel cock knob to “OFF”
when storing the watercraft, otherwise
fuel could leak out into the engine or en-
gine compartment, which would create a
fire hazard.
Storage for long periods of time, such as win-
ter storage, requires preventive maintenance
to ensure against deterioration. It is advisable
to have the watercraft serviced by a Yamaha
dealer prior to storage. However, the following
procedures can be performed by the owner.
EJU33513Flushing the cooling system
Flushing the cooling system is essential to
prevent it from clogging with salt, sand, or dirt.
(1) Place the watercraft in a horizontal posi-
tion.
(2) Remove the hood. (See page 17 for hood
removal and installation procedures.)
(3) Remove the flushing hose connector
cap, and then insert the garden hoseadapter into the flushing hose connector
and turn it until it is securely connected.
(4) Connect the garden hose adapter to a
water tap using a garden hose.
TIP:
A garden hose is not included.
(5) Start the engine, and then immediately
turn the water supply on until water flows
out continually from the cooling water pi-
lot outlet. NOTICE: Do not run the en-
gine for more than 15 seconds without
supplying water, otherwise the engine
could overheat.
[ECJ01010]
TIP:
If you will be storing the watercraft for a pro-
longed period, such as winter storage, top off
the fuel tank with fresh gasoline and add fuel
stabilizer and conditioner to the fuel tank ac-
cording to the manufacturer’s instruction be-
fore starting the engine.
(6) Run the engine at idling speed for about
3 minutes watching the engine condition.
If the engine stops while flushing, turn the
water supply off immediately and repeat
the above steps. NOTICE: Do not sup-
ply water to the cooling water passag-
es when the engine is not running. The
water could flow back through the
1Garden hose adapter
2Flushing hose connector
3Flushing hose connector cap
UF2F71E0.book Page 45 Thursday, April 10, 2008 11:47 AM
Maintenance and care
49
EJU33821Periodic maintenance chart
The following chart gives general guidelines for periodic maintenance. However, maintenance
may need to be performed more frequently depending on your operating conditions.
This “ ” mark indicates maintenance that you may do yourself.
This “ ” mark indicates work to be done by a Yamaha dealer.
Item OperationInitial Thereafter every
Page 10
hours50
hours100
hours100
hours200
hours
6
months12
months12
months24
months
Spark plugsCheck, clean, adjust 55
Lubrication pointsLubricate 56
Intermediate hous-
ingLubricate 56
Fuel systemCheck 51
Fuel filterCheck, clean, replace 51
Fuel tankCheck, clean 51
CarburetorCheck, adjust 58
Trolling speedCheck, adjust 58
Carburetor throt-
tle shaftCheck —
Cooling water pas-
sagesFlush
*45
Bilge strainerClean —
ImpellerCheck —
Jet thrust nozzle
angleCheck, adjust 51
Handlebar pivot
shaftCheck —
Steering frictionCheck, adjust 52
Throttle cableCheck, adjust 54
Choke cableCheck, adjust 57
BatteryCheck, charge 57
Rubber couplingCheck —
Engine mountCheck —
UF2F71E0.book Page 49 Thursday, April 10, 2008 11:47 AM
Maintenance and care
51
EJU34202Checking the fuel system
WARNING
EWJ00381
Leaking fuel can result in fire or explosion.
Check for fuel leakage regularly.
If any fuel leakage is found, the fuel sys-
tem must be repaired by a qualified me-
chanic. Improper repairs can make the
watercraft unsafe to operate.
Check the fuel system for leaks, cracks, and
malfunctions. If any problem is found, consult
a Yamaha dealer.
Check:
Carburetor for leakage
Fuel tank filler cap and seal for damage
Fuel in fuel tank for water and dirt
Fuel tank for damage, cracks, and leakage
Fuel hoses and joints for damage, cracks,
and leakage
Fuel filter for leakage
Fuel cock for leakage
Air vent check valve for leakageEJU34221Fuel filter
Check the fuel filter. If water or dirt is found in
the fuel filter, have a Yamaha dealer replace
it.
EJU34230Fuel tank
Check the fuel tank for leakage and for water
in the tank. If water is found in the fuel system,
or if the fuel tank needs to be cleaned, have a
Yamaha dealer service the watercraft.
EJU34321Checking the jet thrust nozzle angle
Check the handlebars and jet thrust nozzle for
smooth operation.
Turn the handlebars as far as possible to the
right and left and check that the difference of
distances A and B between the jet thrust noz-
zle and the nozzle is within specification.
1Fuel filter
1Fuel tank
UF2F71E0.book Page 51 Thursday, April 10, 2008 11:47 AM
Specifications
60
EJU34542
Specifications
Watercraft capacity:
Maximum people on board:
1 person
Dimensions:
Length:
2240 mm (88.2 in)
Width:
680 mm (26.8 in)
Height:
660 mm (26.0 in)
Dry weight:
139 kg (306 lb)
Performance:
Maximum output (according to ISO 8665/SAE
J1228):
48.50 kW@6250 r/min
Maximum fuel consumption:
29.0 L/h (7.7 US gal/h, 6.4 Imp.gal/h)
Cruising range at full throttle:
0.62 hour
Trolling speed:
1300 ±50 r/min
Engine:
Engine type:
2-stroke
Number of cylinders:
2
Engine displacement:
701 cm³
Bore & stroke:
81.0 × 68.0 mm (3.19 × 2.68 in)
Compression ratio:
7.2 : 1
Lubrication system:
Pre-mixed fuel and oil
Cooling system:
Water
Starting system:
Electric
Ignition system:
C.D.I.
Spark plug:
BR7HS
Spark plug gap:
0.6–0.7 mm (0.024–0.028 in)
Battery capacity:
12 V, 19.0 AhCharging system:
Flywheel magneto
Drive unit:
Propulsion system:
Jet pump
Jet pump type:
Axial flow, single stage
Impeller rotation:
Counterclockwise
Jet thrust nozzle angle:
P1: 14.4+14.4 °
P2: 17.3+17.3 °
Fuel and oil:
Recommended fuel:
Regular unleaded gasoline
Minimum octane rating (PON):
86
Minimum octane rating (RON):
90
Recommended engine oil:
YAMALUBE 2-W or TC-W3 outboard motor
oil or equivalent
Fuel mixing ratio (fuel to oil):
50 :1
Fuel tank total capacity:
18 L (4.8 US gal, 4.0 Imp.gal)
Fuel tank reserve capacity:
5.5 L (1.5 US gal, 1.2 Imp.gal)
UF2F71E0.book Page 60 Thursday, April 10, 2008 11:47 AM
Trouble recovery
61
EJU34560
Troubleshooting
If you have any trouble with your watercraft, use this section to check for the possible cause.
If you cannot find the cause, or if the procedure for replacement or repair is not described in
this owner’s/operator’s manual, have a Yamaha dealer perform the necessary service.
EJU34571Troubleshooting chart
TROUBLE POSSIBLE CAUSE REMEDY PAGE
Engine does not
start (Starter motor
does not turn over)Engine shut-
off switchClip not in place Install clip
19
Fuse Burned out Replace fuse and
check wiring64
Battery Run down Recharge 57
Poor terminal con-
nectionsTighten as required
57
Terminal corroded Clean 46
Starter motor Faulty Have serviced by
Yamaha dealer—
Engine does not
start (Starter motor
turns over)Fuel cock Turned to “OFF” Turn fuel cock knob to
“ON”18
Fuel Empty Refill as soon as pos-
sible25
Stale or contaminat-
edHave serviced by
Yamaha dealer51
Fuel tank Water or dirt present Have serviced by
Yamaha dealer51
Spark plug Fouled or defective Clean or replace 55
Spark plug
capNot connected or
looseConnect properly
55
Crankcase Filled with water Have serviced by
Yamaha dealer65
Fuel filter Clogged or water
pooledHave serviced by
Yamaha dealer51
Choke Knob moves back on
its ownTighten choke knob
adjusting nut57
UF2F71E0.book Page 61 Thursday, April 10, 2008 11:47 AM
Trouble recovery
62
Engine runs irregu-
larly or stallsFuel Empty Refill as soon as pos-
sible25
Stale or contaminat-
edHave serviced by
Yamaha dealer51
Too much oil in fuel
mixing ratioCorrect fuel-to-oil ra-
tio to 50:124
Choke Knob is left pulled Push fully in 20
Fuel filter Clogged or water
pooledHave serviced by
Yamaha dealer51
Fuel tank Water or dirt present Have serviced by
Yamaha dealer51
Spark plug Fouled or defective Replace 55
Incorrect heat range Replace 55
Gap incorrect Adjust 55
Spark plug
capLoose Connect properly 55
Cracked, torn or dam-
agedHave serviced by
Yamaha dealer—
Electrical wir-
ingLoose electrical con-
nectionsHave serviced by
Yamaha dealer—
Carburetor Incorrect idle adjust-
mentAdjust idle
58
Clogged Have serviced by
Yamaha dealer58
Watercraft slow or
loses powerCavitation Jet intake clogged Clean 63
Impeller damaged or
wornHave serviced by
Yamaha dealer63
Engine over-
heatedJet intake clogged Clean
63
Fuel filter Clogged Have serviced by
Yamaha dealer51
Spark plug Fouled or defective Replace 55
Incorrect heat range Replace 55
Gap incorrect Adjust 55
Spark plug
capsLoose Connect properly
55
Fuel Stale or contaminat-
edHave serviced by
Yamaha dealer51 TROUBLE POSSIBLE CAUSE REMEDY PAGE
UF2F71E0.book Page 62 Thursday, April 10, 2008 11:47 AM
Trouble recovery
65
system damage and possible fire.
[EWJ00801]
EJU34702
Towing the watercraft
WARNING
EWJ00811
The operator of the towing boat must
keep speed to a minimum and avoid traf-
fic or obstacles which could be a hazard
to the operator on the watercraft.
The towline should be long enough so
that the watercraft will not collide with
the towing boat when slowing down.
If the watercraft becomes inoperative in the
water, it can be towed to shore.
When the watercraft is towed using a towline,
the operator should ride the watercraft, hold-
ing onto the handlebars and supporting his or
her body weight on the riding tray. This will
help keep the bow of the watercraft out of the
water.
Use a towline that is three times the combined
length of the towing boat and the watercraft.Tow the watercraft using the bow rope hole
only.
Tow the watercraft at 5 mph (8 km/h) or less.
The bow must be kept up out of the water dur-
ing towing to prevent water from entering the
engine compartment.
EJU34731Submerged watercraft
If the watercraft is submerged or flooded with
water, follow the procedure below and consult
a Yamaha dealer as soon as possible. Failure
to do so could result in serious engine dam-
age.
(1) Beach the watercraft and remove the
hood.
(2) Turn the fuel cock knob to “OFF”.
(3) Turn the watercraft over far enough to
drain the water from the engine compart-
ment. NOTICE: Turning the watercraft
on its side with the hood removed
could cause damage to the steering
pole. Use two people to provide
enough support to make sure that the
steering pole is not damaged.
[ECJ00701]
(4) Turn the watercraft upright again.
(5) Have the watercraft inspected by a
Yamaha dealer as soon as possible.
NOTICE: Be sure to have a Yamaha
dealer inspect the watercraft. Other-
wise, serious engine damage could re-
sult.
[ECJ00791]
1Electrical box
2Fuse holder
3Cap
4Fuse
Fuse amperage:
Battery fuse:
10 A
1Bow rope hole
UF2F71E0.book Page 65 Thursday, April 10, 2008 11:47 AM
Index
2-stroke engine oil .................................... 24
B
Battery ................................................ 28, 46
Battery, checking...................................... 57
Battery, jumping ....................................... 64
Beaching the watercraft ........................... 42
Bilge ......................................................... 28
Boarding and starting in deep water ........ 38
Boarding and starting in shallow water .... 37
Bow rope hole .......................................... 22
C
Capsized watercraft ................................. 39
Carburetor, adjusting................................ 58
Choke cable, adjusting ............................. 57
Choke knob .............................................. 20
Cleaning the watercraft ............................ 47
Cooling water pilot outlet .................... 20, 31
Craft Identification Number (CIN) ............... 1
Cruising limitations ..................................... 8
E
Emergency procedures ............................ 63
Engine break-in ........................................ 32
Engine compartment ................................ 27
Engine overheat warning system ............. 22
Engine serial number ................................. 1
Engine shut-off cord (lanyard) .................. 30
Engine shut-off switch .............................. 19
Engine stop switch ................................... 19
Enjoy your watercraft responsibly ............ 14
F
Fire extinguisher....................................... 28
Flushing the cooling system ..................... 45
Fuel and oil............................................... 24
Fuel cock knob ......................................... 18
Fuel filter .................................................. 51
Fuel system .............................................. 27
Fuel system, checking.............................. 51
Fuel tank .................................................. 51
Fuel tank filler cap .................................... 18
Fuel tank, filling ........................................ 25
Fuse, replacing......................................... 64
G
Gasohol .................................................... 24
Gasoline ................................................... 24Getting to know your watercraft ............... 35
H
Hazard information ................................... 12
Hood ......................................................... 17
Hull and deck ........................................... 27
I
Identification numbers ................................ 1
J
Jet intake .................................................. 30
Jet intake and impeller, cleaning .............. 63
Jet thrust nozzle angle, adjusting ............. 53
Jet thrust nozzle angle, checking ............. 51
Jumper cables, connecting ...................... 64
K
Kneeling ................................................... 36
L
Labels, important ........................................ 2
Labels, other .............................................. 6
Labels, warning .......................................... 3
Launching the watercraft .......................... 32
Learning to operate your watercraft ......... 35
Leaving the watercraft .............................. 34
Limitations on who may operate the
watercraft ................................................ 7
Lubrication................................................ 46
Lubrication points ..................................... 56
M
Main components, location of .................. 15
Maintenance and adjustments ................. 47
Mixing fuel and oil .................................... 24
O
Operating in weeded areas ...................... 42
Operating positions .................................. 36
Operating your watercraft ......................... 35
Operation ................................................. 32
Operation of controls and other
functions ............................................... 17
Operation requirements ............................. 9
Owner’s/operator’s manual and tool kit .... 47
P
Periodic maintenance chart ...................... 49
Post-operation care .................................. 42
Pre-operation check list ............................ 26
Pre-operation check points ...................... 27
Pre-operation checks ............................... 26
UF2F71E0.book Page 1 Thursday, April 10, 2008 11:47 AM