2009 YAMAHA GRIZZLY 450 battery

Checking the front brake lever free
play ......................................................... 8-41
Adjusting the brake pedal and rear brake
lever free play and checking the brake
pedal position ......................................... 8-42
Axle boots ................................................ 8-46
Brake light switches ................................. 8-47
Checking and lubricating the cables ........ 8-48
Checking and lubricating the front and
rear brake levers .................................... 8-48
Checking and lubricating the brake
pedal ...................................................... 8-48
Checking the wheel hub bearings ............ 8-49
Lubricating the drive shaft universal
joint ......................................................... 8-49
Checking the stabilizer bushes ................ 8-49
Lubricating the rear knuckle pivots ........... 8-50
Lubricating the steering shaft ................... 8-50
Battery ...................................................... 8-50
Replacing a fuse ...................................... 8-52
Replacing a headlight bulb ....................... 8-54
Adjusting a headlight beam ...................... 8-56
Replacing the tail/brake light bulb ............ 8-56
Removing a wheel .................................... 8-58
Installing a wheel ...................................... 8-58
Troubleshooting ....................................... 8-60
Troubleshooting charts ............................. 8-61CLEANING AND STORAGE ..........................9-1
Cleaning ......................................................9-1
Storage .......................................................9-2
SPECIFICATIONS .......................................10-1
CONSUMER INFORMATION.......................11-1
Identification numbers ...............................11-1
U37S60E0.book Page 3 Thursday, June 5, 2008 6:51 PM

3-1
3
EBU17680
DESCRIPTION
EBU17690Left view
EBU17700Right view
1. Radiator cap
2. Fuel cock
3. Recoil starter
4. Throttle stop screw
5. Air filter case
6. Battery
7. Fuses
8. Tail/brake light
9. Engine oil filler cap
10.Oil filter cartridge
11.Coolant reservoir
12.V-belt cooling duct check hose
1. Rear shock absorber assembly spring preload adjusting
ring
2. Spark arrester
3. Rear storage compartment and tool kit
4. Spark plug
5. Front shock absorber assembly spring preload adjusting
ring
6. Rear brake light switch
7. Brake pedal
8. V-belt case drain plug
U37S60E0.book Page 1 Thursday, June 5, 2008 6:51 PM

4-6
4
EBU18080Engine stop switch“/”
Set this switch to“” before starting the engine.
The engine stop switch controls the ignition and
stops the engine when it is running. Use this switch
to stop the engine in an emergency situation. The
engine will not start or run when this switch is set
to“”.EBU18100Start switch“”
Push this switch to crank the engine with the start-
er.NOTICEECB00050See the starting instructions on page 6-1 priorto starting the engine.EBU18151Light switch“//OFF”
Set this switch to“” to turn on the low beams
and the taillight. Set the switch to“” to turn on
the high beams and the taillight. Set the switch to
“OFF” to turn off all the lights.
NOTICEECB00040Do not use the headlights with the engine
turned off for an extended period of time, oth-
erwise the battery may discharge to the point
that the starter motor will not operate properly.
If this should happen, remove the battery andrecharge it.EBU18170Horn switch“”
Press the switch to sound the horn.EBU18190Override switch “OVERRIDE” 1. Override switch “OVERRIDE”
U37S60E0.book Page 6 Thursday, June 5, 2008 6:51 PM

4-24
4

If accessories are used without the engine
running or with the headlights turned on, the
battery will lose its charge and engine start-
ing may become difficult.
Do not use an automotive cigarette lighter or
other accessories with a plug that gets hotbecause the jack can be damaged.
U37S60E0.book Page 24 Thursday, June 5, 2008 6:51 PM

6-2
64. Use the starter (choke) in reference to the fig-
ure:
Position (1):
Cold engine start with ambient temperature
below 5 °C (40 °F).
Position (2):
Cold engine start with ambient temperature
between 0 °C (30 °F) and 30 °C (90 °F).
Position (3):
Cold engine start with ambient temperature
above 25 °C (80 °F).5. Apply the rear brake lever.
6. Completely close the throttle lever and start
the engine by pushing the start switch.
TIP
If the engine fails to start, release the start
switch, then push it again. Pause a few seconds
before the next attempt. Each cranking should
be as short as possible to preserve battery ener-
gy. Do not crank the engine more than 10 sec-
onds on each attempt.
If the battery is discharged, pull the recoil starterto start the engine.
7. If the engine is started with the starter (choke)
in position (1), the starter (choke) should be
returned to position (2) to warm up the engine.
If the engine is started with the starter (choke)
in position (2), keep the starter (choke) in this
position to warm up the engine.NOTICEECB00160For maximum engine life, always warm the en-
gine up before starting off. Never acceleratehard when the engine is cold!
1. Fully open
2. Half open
3. Closed
4. Starter (choke)U37S60E0.book Page 2 Thursday, June 5, 2008 6:51 PM

8-50
8
EBU25051Lubricating the rear knuckle pivots The rear knuckle pivots must be lubricated at the
intervals specified in the periodic maintenance and
lubrication chart.
Lubricate the pivoting points using a grease gun.
EBU25102Lubricating the steering shaft The steering shaft must be lubricated at the inter-
vals specified in the periodic maintenance and lu-
brication chart.EBU29182Battery This model is equipped with a VRLA (Valve Regu-
lated Lead Acid) battery. There is no need to check
the electrolyte or to add distilled water. However,
the battery lead connections need to be checked
and, if necessary, tightened.NOTICEECB00620Never attempt to remove the battery cell seals,as this would permanently damage the battery. Recommended lubricant:
Lithium-soap-based grease
1. Grease nipple
Recommended lubricant:
Lithium-soap-based grease
U37S60E0.book Page 50 Thursday, June 5, 2008 6:51 PM

8-51
8
WARNING
EWB02160Battery electrolyte is poisonous and danger-
ous, as it contains sulfuric acid, which can
cause severe burns. Avoid contact with skin,
eyes or clothing. Always shield your eyes
when working near batteries.
Antidote:
EXTERNAL: Flush with water.
INTERNAL: Drink large quantities of water or
milk. Follow with milk of magnesia, beaten egg
or vegetable oil. Call a physician immediately.
EYES: Flush with water for 15 minutes and get
prompt medical attention.
Batteries produce explosive gases. Keep
sparks, flame, cigarettes or other sources of ig-
nition away. Ventilate when charging or using
in an enclosed space.KEEP OUT OF REACH OF CHILDREN.
To remove the battery
1. Remove the seat. (See page 4-18.)
2. Remove the battery holding plate by removing
the bolts.3. Disconnect the negative battery lead first,
then the positive battery lead by removing
their bolt.
4. Pull the battery out of its compartment.
To charge the battery
Have a Yamaha dealer charge the battery as soon
as possible if it seems to have discharged. Keep in
mind that the battery tends to discharge more
quickly if the ATV is equipped with optional electri-
cal accessories.
1. Bolt
2. Battery holding plate
3. Positive battery lead (red)
4. Negative battery lead (black)
3
4
12
U37S60E0.book Page 51 Thursday, June 5, 2008 6:51 PM

8-52
8
NOTICEECB00930To charge a VRLA (Valve Regulated Lead Acid)
battery, a special (constant-voltage) battery
charger is required. Using a conventional bat-
tery charger will damage the battery. If you do
not have access to a constant-voltage battery
charger, have a Yamaha dealer charge yourbattery.
To store the battery
If the ATV will not be used for more than one
month, remove the battery, fully charge it, and
then place it in a cool, dry place.
If the battery will be stored for more than two
months, check it at least once a month and fully
charge it if necessary.
To install the batteryTIPBe sure the battery is fully charged.
1. Place the battery in its compartment.
2. Connect the positive battery lead first, then
connect the negative battery lead by installing
their bolt.3. Install the battery holding plate by installing
the bolts.
4. Install the seat. (See page 4-18.)
NOTICEECB00940Always keep the battery charged. Storing a dis-
charged battery can cause permanent batterydamage.EBU25325Replacing a fuse The main fuse and the fuse box are located under
the seat. (See page 4-18.)1. Positive battery lead (red)
2. Negative battery lead (black)
1
2
U37S60E0.book Page 52 Thursday, June 5, 2008 6:51 PM