2009 YAMAHA GRIZZLY 350 lock

8-45
84. If the fuse immediately blows again, have a
Yamaha dealer check the electrical system.
EBU25480Replacing a headlight bulb If a headlight bulb burns out, replace it as follows.
1. Remove the cover at the rear of the headlight
by pulling it off.
2. Remove the headlight bulb holder cover by
pulling it off.3. Remove the headlight bulb holder by pushing
it in and turning it counterclockwise.1. Cover at the rear of the headlight
1. Headlight bulb holder cover
1. Headlight bulb holder
U4S262E0.book Page 45 Tuesday, June 10, 2008 11:40 AM

8-46
8 4. Remove the defective bulb by pulling it out.
WARNING
EWB02220A headlight bulb is hot when it is on and imme-
diately after it is turned off. Wait for the bulb to
cool before touching or removing it. You can
be burned or a fire could start if the bulb touch-es something flammable.
5. Insert a new headlight bulb into the bulb hold-
er by pushing it in.
NOTICEECB00650Do not touch the glass part of the headlight
bulb to keep it free from oil, otherwise the
transparency of the glass, the luminosity of the
bulb, and the bulb life will be adversely affect-
ed. Thoroughly clean off any dirt and finger-
prints on the headlight bulb using a clothmoistened with alcohol or thinner.
6. Install the bulb holder by pushing it in and turn-
ing it clockwise.
7. Install the bulb holder cover and the cover at
the rear of the headlight.NOTICEECB00670Make sure the headlight bulb holder cover is
securely fitted over the bulb holder and seatedproperly.
8. Adjust the headlight beam if necessary.EBU25551Adjusting a headlight beam NOTICEECB00690It is advisable to have a Yamaha dealer makethis adjustment.
1. Do not touch the glass part of the bulb.U4S262E0.book Page 46 Tuesday, June 10, 2008 11:40 AM

9-1
9
EBU25860
CLEANING AND STORAGE
EBU25880Cleaning Frequent, thorough cleaning of your ATV will not
only enhance its appearance but will improve its
general performance and extend the useful life of
many components.
1. Before cleaning the ATV:
a. Block off the end of the exhaust pipe to
prevent water entry. A plastic bag and
strong rubber band may be used.
b. Make sure the spark plug and all filler caps
are properly installed.
2. If the engine case is excessively greasy, apply
degreaser with a paint brush. Do not apply de-
greaser to the wheel axles.
3. Rinse the dirt and degreaser off with a garden
hose. Use only enough pressure to do the job.NOTICEECB00710Excessive water pressure may cause water
seepage and deterioration of wheel bearings,
brakes, transmission seals and electrical de-
vices. Many expensive repair bills have result-ed from improper high-pressure detergent
applications such as those available in coin-
operated car washers.
4. Once most of the dirt has been hosed off,
wash all surfaces with warm water and mild,
detergent-type soap. An old toothbrush or bot-
tle brush is handy for hard-to-reach places.
5. Rinse the ATV off immediately with clean wa-
ter and dry all surfaces with a chamois, clean
towel or soft absorbing cloth.
6. Clean the seat with a vinyl upholstery cleaner
to keep the cover pliable and glossy.
7. Automotive type wax may be applied to all
painted and chrome plated surfaces. Avoid
combination cleaner-waxes. Many contain
abrasives which may mar the paint or protec-
tive finish. When finished cleaning, start the
engine and let it idle for several minutes.
U4S262E0.book Page 1 Tuesday, June 10, 2008 11:40 AM

9-3
9c. Install the spark plug cap onto the spark
plug, and then place the spark plug on the
cylinder head so that the electrodes are
grounded. (This will limit sparking during
the next step.)
d. Turn the engine over several times with the
starter. (This will coat the cylinder wall with
oil.)
e. Remove the spark plug cap from the spark
plug, and then install the spark plug and
the spark plug cap.
6. Lubricate all control cables and the pivoting
points of all levers and pedals.
7. Check and, if necessary, correct the tire air
pressure, and then block up the ATV so that
all of its wheels are off the ground. Alternative-
ly, turn the wheels a little every month in order
to prevent the tires from becoming degraded
in one spot.
8. Cover the muffler outlet with a plastic bag to
prevent moisture from entering it.
9. Remove the battery and fully charge it. Store
it in a cool, dry place and charge it once a
month. Do not store the battery in an exces-
sively cold or warm place [less than 0 °C (30°F) or more than 30 °C (90 °F)]. For more in-
formation on storing the battery, see page
8-41.
TIPMake any necessary repairs before storing theATV.
U4S262E0.book Page 3 Tuesday, June 10, 2008 11:40 AM

10-4
10
Rim size:
12 x 7.5ATFront brake:Type:
Dual disc brake
Operation:
Right hand operation
Recommended fluid:
DOT 4Rear brake:Type:
Wet multiple disc brake
Operation:
Left hand and right foot operationFront suspension:Type:
Double wishbone
Spring/shock absorber type:
Coil spring/oil damper
Wheel travel:
160 mm (6.3 in)Rear suspension:Type:
Double wishbone
Spring/shock absorber type:
Coil spring/oil damper
Wheel travel:
180 mm (7.1 in)Electrical system:Ignition system:
DC. CDICharging system:
AC magneto
Battery:Model:
YTX14AH
Voltage, capacity:
12 V, 12.0 AhHeadlight:Bulb type:
Krypton bulbBulb voltage, wattage × quantity:Headlight:
12 V, 30.0/30.0 W × 2
Tail/brake light:
12 V, 5.0/21.0 W × 1
Meter lighting:
12 V, 1.7 W × 1
Neutral indicator light:
12 V, 1.7 W × 1
Reverse indicator light:
12 V, 1.7 W × 1
Oil temperature warning light:
12 V, 1.7 W × 1
On-command four-wheel-drive indicator light:
12 V, 1.7 W × 1
Differential gear lock indicator light:
12 V, 1.7 W x 1Fuses:Main fuse:
30.0 A
U4S262E0.book Page 4 Tuesday, June 10, 2008 11:40 AM

INDEX
AAccessories and loading ................................................ 6-6
Air filter element, cleaning ............................................ 8-21
Axle boots .................................................................... 8-36BBattery .......................................................................... 8-41
Brake fluid, changing ................................................... 8-31
Brake fluid level, checking ........................................... 8-30
Brake lever free play, checking the front ...................... 8-31
Brake lever, front .......................................................... 4-11
Brake levers, checking and lubricating ........................ 8-38
Brake light switches ..................................................... 8-37
Brake pads and friction plates, checking ..................... 8-29
Brake pedal and brake lever free play (rear) and
brake pedal position, adjusting and checking ............ 8-32
Brake pedal and rear brake lever ................................. 4-11
Brake pedal, checking and lubricating ......................... 8-39
Brakes, front and rear .................................................... 5-3CCables, checking and lubricating ................................. 8-38
Carburetor, adjusting ................................................... 8-26
Carrier, front ................................................................. 4-19
Carrier, rear .................................................................. 4-19
Chassis fasteners .......................................................... 5-6
Cleaning ......................................................................... 9-1DDifferential gear lock indicator light ................................ 4-3
Differential gear oil ................................................ 5-3, 8-19Drive select lever ......................................................... 4-12
Drive select lever and driving in reverse ........................ 6-3
Drive select lever safety system cable, adjusting ........ 8-29
Drive shaft universal joint, lubricating .......................... 8-39
EEngine break-in .............................................................. 6-4
Engine, cold start ........................................................... 6-1
Engine idling speed ..................................................... 8-26
Engine oil ....................................................................... 5-3
Engine oil and oil filter cartridge ................................... 8-11
Engine, starting a warm ................................................. 6-3
Engine stop switch ......................................................... 4-4FFinal gear oil ......................................................... 5-3, 8-15
Four-wheel-drive indicator light ...................................... 4-3
Fuel ....................................................................... 4-14, 5-3
Fuel cock ..................................................................... 4-15
Fuel tank cap ............................................................... 4-13
Fuses, replacing .......................................................... 8-43HHandlebar switches ....................................................... 4-4
Headlight beam, adjusting ........................................... 8-46
Headlight bulb, replacing ............................................. 8-45
Horn switch .................................................................... 4-5IIdentification numbers .................................................. 11-1
Indicator lights and warning light ................................... 4-2
Instruments, lights and switches .................................... 5-6
U4S262E0.book Page 1 Tuesday, June 10, 2008 11:40 AM

KKey identification number ............................................. 11-1LLabel locations ............................................................... 2-1
Light switch .................................................................... 4-5MMain switch .................................................................... 4-1
Maintenance and lubrication chart ................................. 8-5
Maintenance chart, emission control system ................. 8-3
Model label ................................................................... 11-2NNeutral indicator light ..................................................... 4-2OOil temperature warning light ......................................... 4-2
On-Command differential gear lock switch .................... 4-7
On-Command four-wheel-drive switch ........................... 4-6
Override switch .............................................................. 4-5
Owner’s manual and tool kit ........................................... 8-1PPanel, removing and installing ....................................... 8-9
Parking ........................................................................... 6-5
Parking brake ............................................................... 4-12
Parking on a slope ......................................................... 6-5
Part locations ................................................................. 3-1
Pre-operation check list .................................................. 5-1RRear knuckle pivots, lubricating ................................... 8-40
Recoil starter ................................................................ 4-13
Reverse indicator light .................................................... 4-2
Riding your ATV ............................................................. 7-1
SSafety information .......................................................... 1-1
Seat .............................................................................. 4-17
Shock absorber assemblies, adjusting the front and
rear ............................................................................ 4-19
Spark arrester, cleaning ............................................... 8-24
Spark plug, checking ...................................................... 8-9
Specifications ............................................................... 10-1
Speed limiter ................................................................ 4-10
Speedometer .................................................................. 4-3
Stabilizer bushes, checking .......................................... 8-40
Starter (choke) ............................................................. 4-16
Start switch ..................................................................... 4-5
Steering shaft, lubricating ............................................. 8-40
Storage ........................................................................... 9-2
Storage compartment ................................................... 4-18TTail/brake light bulb, replacing ..................................... 8-47
Throttle cable free play, adjusting ................................ 8-28
Throttle lever ........................................................... 4-9, 5-4
Tire pressure, measuring ............................................... 5-5
Tires ............................................................................... 5-4
Tire wear limit ................................................................. 5-6
Troubleshooting ........................................................... 8-49
Troubleshooting chart .................................................. 8-50VValve clearance ............................................................ 8-28
V-belt case drain plug .................................................. 8-26
V-belt cooling duct check hose .................................... 8-25
Vehicle identification number ....................................... 11-1WWheel hub bearings, checking ..................................... 8-39
U4S262E0.book Page 2 Tuesday, June 10, 2008 11:40 AM