2009 YAMAHA GRIZZLY 350 brake light

6-4
6 3. Shift from neutral to reverse and vice versa by
moving the drive select lever along the shift
guide.
TIPWhen in reverse, the reverse indicator light should
come on. If the indicator light does not come on,have a Yamaha dealer check the electrical circuit.
4. Check behind for people or obstacles, and
then release the brake pedal.5. Open the throttle lever gradually and continue
to watch to the rear while backing.
WARNING
EWB00720Improper operation in reverse could make you
hit an obstacle or even a person behind you,
resulting in serious injury. When you shift into
reverse, make sure there are no people or ob-
stacles behind you. When it is safe to proceed,go slowly.EBU20682Engine break-in TIP
For ATVs equipped with an odometer or an hour
meter, follow the figures given in km (mi) or the
figures given in hours.
For ATVs not equipped with an odometer orhour meter, follow the figures given in hours.
There is never a more important period in the life of
your engine than the first 320 km (200 mi) or 20
hours of riding. For this reason, you should read
the following material carefully.
Since the engine is brand new, do not put an ex-
cessive load on it for the first 320 km (200 mi) or 20
hours. The various parts in the engine wear and
1. Drive select lever
2. F (Forward)
3. N (Neutral)
4. R (Reverse)U4S262E0.book Page 4 Tuesday, June 10, 2008 11:40 AM

7-13
7With the engine idling, return the starter (choke) to
the closed position, shift the drive select lever into
the forward position, and then release the parking
brake. Apply the throttle slowly and smoothly. The
centrifugal clutch will engage and you will start to
accelerate. If the throttle is applied too abruptly, the
front wheels may lift off the ground, resulting in a
loss of directional control. Avoid higher speeds un-
til you are thoroughly familiar with the operation of
your ATV.
When slowing down or stopping, release the throt-
tle and apply the brakes smoothly and evenly. Im-
proper use of the brakes can cause the tires to lose
traction, reducing control and increasing the possi-
bility of an accident.
TURNING YOUR ATV
To achieve maximum traction on unpaved surfac-
es in 2WD or 4WD, the two rear wheels turn to-
gether at the same speed. Furthermore, when
riding in 4WD-LOCK (“DIFF. LOCK”), the front
wheels also turn together at the same speed.
Therefore, unless the wheel on the inside of the
turn is allowed to slip or lose some traction, the
ATV will resist turning. A special turning techniquemust be used to allow the ATV to make turns
quickly and easily. It is essential that this skill be
learned first at low speed.
WARNING
EWB01770Always follow proper procedures for turning
as described in this Owner’s Manual. Practice
turning at low speeds before attempting to turn
at faster speeds. Do not turn at speeds too fast
for your skills or the conditions. Operate at a
slow speed and allow extra time and distance
for maneuvers when in 4WD-LOCK (“DIFF.LOCK”).
As you approach a curve, slow down and begin to
turn the handlebars in the desired direction. As you
do so, put your weight on the footboard to the out-
side of the turn (opposite your desired direction)
and lean your upper body into the turn. Use the
throttle to maintain an even speed through the turn.
This maneuver will let the wheel on the inside of
the turn slip slightly, allowing the ATV to make the
turn properly.
U4S262E0.book Page 13 Tuesday, June 10, 2008 11:40 AM

8-7
8
EBU28390TIP
The air filter needs more frequent service if you are riding in unusually wet or dusty areas.
Hydraulic brake service
Regularly check and, if necessary, correct the brake fluid level.21 Final gear oilChange.
Check ATV for oil leakage, and correct if neces-
sary.√√√
22*Moving parts and
cablesLubricate.√√√√
23*Drive select lever
safety system cableCheck operation and adjust or replace if neces-
sary.√√√
24*Throttle lever hous-
ing and cableCheck operation and correct if necessary.
Check throttle cable free play and adjust if neces-
sary.
Lubricate throttle lever housing and cable.√√√√√
25*Front and rear brake
switchesCheck operation and correct if necessary.√√√√√
26*Lights and switchesCheck operation and correct if necessary.
Adjust headlight beams.√√√√√ NO. ITEMCHECK OR MAINTENANCE
JOBINITIAL EVERY
Whichev-
er comes
firstmonth136612
km
(mi)320
(200)1300
(800)2500
(1600)2500
(1600)5000
(3200)
hours 20 80 160 160 320U4S262E0.book Page 7 Tuesday, June 10, 2008 11:40 AM

8-37
8
EBU24752Brake light switches The operation of the brake light switches must be
checked and, if necessary, adjusted at the inter-
vals specified in the periodic maintenance and lu-
brication chart.
The brake light switch for the brake pedal can be
adjusted as follows, but the other brake light
switches should be adjusted by a Yamaha dealer.
1. Remove panel A. (See page 8-9.)
TIPThe brake light switch is properly adjusted when
the brake light comes on just before braking takeseffect.
2. Turn the brake light switch adjusting nut while
holding the brake light switch in place. To
make the brake light come on earlier, turn the
adjusting nut in direction (a). To make the
brake light come on later, turn the adjusting
nut in direction (b).
3. Install the panel.
1. Rear axle boot (each side)
1. Brake light switch
2. Brake light switch adjusting nut
U4S262E0.book Page 37 Tuesday, June 10, 2008 11:40 AM

8-47
8To raise a headlight beam, turn the headlight beam
adjusting screw in direction (a).
To lower a headlight beam, turn the adjusting
screw in direction (b).
EBU25580Replacing the tail/brake light bulb If the tail/brake light bulb burns out, have a
Yamaha dealer replace it.EBU25651Removing a wheel 1. Place the ATV on a level surface.
2. Loosen the wheel nuts.3. Elevate the ATV and place a suitable stand
under the frame.
4. Remove the nuts from the wheel.
5. Remove the wheel.
EBU25701Installing a wheel 1. Place the ATV on a level surface.
2. Install the wheel and the nuts.TIP
The arrow mark on the tire must point toward
the rotating direction of the wheel.
1. Headlight beam adjusting screw
1. Wheel nut
U4S262E0.book Page 47 Tuesday, June 10, 2008 11:40 AM

10-4
10
Rim size:
12 x 7.5ATFront brake:Type:
Dual disc brake
Operation:
Right hand operation
Recommended fluid:
DOT 4Rear brake:Type:
Wet multiple disc brake
Operation:
Left hand and right foot operationFront suspension:Type:
Double wishbone
Spring/shock absorber type:
Coil spring/oil damper
Wheel travel:
160 mm (6.3 in)Rear suspension:Type:
Double wishbone
Spring/shock absorber type:
Coil spring/oil damper
Wheel travel:
180 mm (7.1 in)Electrical system:Ignition system:
DC. CDICharging system:
AC magneto
Battery:Model:
YTX14AH
Voltage, capacity:
12 V, 12.0 AhHeadlight:Bulb type:
Krypton bulbBulb voltage, wattage × quantity:Headlight:
12 V, 30.0/30.0 W × 2
Tail/brake light:
12 V, 5.0/21.0 W × 1
Meter lighting:
12 V, 1.7 W × 1
Neutral indicator light:
12 V, 1.7 W × 1
Reverse indicator light:
12 V, 1.7 W × 1
Oil temperature warning light:
12 V, 1.7 W × 1
On-command four-wheel-drive indicator light:
12 V, 1.7 W × 1
Differential gear lock indicator light:
12 V, 1.7 W x 1Fuses:Main fuse:
30.0 A
U4S262E0.book Page 4 Tuesday, June 10, 2008 11:40 AM

INDEX
AAccessories and loading ................................................ 6-6
Air filter element, cleaning ............................................ 8-21
Axle boots .................................................................... 8-36BBattery .......................................................................... 8-41
Brake fluid, changing ................................................... 8-31
Brake fluid level, checking ........................................... 8-30
Brake lever free play, checking the front ...................... 8-31
Brake lever, front .......................................................... 4-11
Brake levers, checking and lubricating ........................ 8-38
Brake light switches ..................................................... 8-37
Brake pads and friction plates, checking ..................... 8-29
Brake pedal and brake lever free play (rear) and
brake pedal position, adjusting and checking ............ 8-32
Brake pedal and rear brake lever ................................. 4-11
Brake pedal, checking and lubricating ......................... 8-39
Brakes, front and rear .................................................... 5-3CCables, checking and lubricating ................................. 8-38
Carburetor, adjusting ................................................... 8-26
Carrier, front ................................................................. 4-19
Carrier, rear .................................................................. 4-19
Chassis fasteners .......................................................... 5-6
Cleaning ......................................................................... 9-1DDifferential gear lock indicator light ................................ 4-3
Differential gear oil ................................................ 5-3, 8-19Drive select lever ......................................................... 4-12
Drive select lever and driving in reverse ........................ 6-3
Drive select lever safety system cable, adjusting ........ 8-29
Drive shaft universal joint, lubricating .......................... 8-39
EEngine break-in .............................................................. 6-4
Engine, cold start ........................................................... 6-1
Engine idling speed ..................................................... 8-26
Engine oil ....................................................................... 5-3
Engine oil and oil filter cartridge ................................... 8-11
Engine, starting a warm ................................................. 6-3
Engine stop switch ......................................................... 4-4FFinal gear oil ......................................................... 5-3, 8-15
Four-wheel-drive indicator light ...................................... 4-3
Fuel ....................................................................... 4-14, 5-3
Fuel cock ..................................................................... 4-15
Fuel tank cap ............................................................... 4-13
Fuses, replacing .......................................................... 8-43HHandlebar switches ....................................................... 4-4
Headlight beam, adjusting ........................................... 8-46
Headlight bulb, replacing ............................................. 8-45
Horn switch .................................................................... 4-5IIdentification numbers .................................................. 11-1
Indicator lights and warning light ................................... 4-2
Instruments, lights and switches .................................... 5-6
U4S262E0.book Page 1 Tuesday, June 10, 2008 11:40 AM

KKey identification number ............................................. 11-1LLabel locations ............................................................... 2-1
Light switch .................................................................... 4-5MMain switch .................................................................... 4-1
Maintenance and lubrication chart ................................. 8-5
Maintenance chart, emission control system ................. 8-3
Model label ................................................................... 11-2NNeutral indicator light ..................................................... 4-2OOil temperature warning light ......................................... 4-2
On-Command differential gear lock switch .................... 4-7
On-Command four-wheel-drive switch ........................... 4-6
Override switch .............................................................. 4-5
Owner’s manual and tool kit ........................................... 8-1PPanel, removing and installing ....................................... 8-9
Parking ........................................................................... 6-5
Parking brake ............................................................... 4-12
Parking on a slope ......................................................... 6-5
Part locations ................................................................. 3-1
Pre-operation check list .................................................. 5-1RRear knuckle pivots, lubricating ................................... 8-40
Recoil starter ................................................................ 4-13
Reverse indicator light .................................................... 4-2
Riding your ATV ............................................................. 7-1
SSafety information .......................................................... 1-1
Seat .............................................................................. 4-17
Shock absorber assemblies, adjusting the front and
rear ............................................................................ 4-19
Spark arrester, cleaning ............................................... 8-24
Spark plug, checking ...................................................... 8-9
Specifications ............................................................... 10-1
Speed limiter ................................................................ 4-10
Speedometer .................................................................. 4-3
Stabilizer bushes, checking .......................................... 8-40
Starter (choke) ............................................................. 4-16
Start switch ..................................................................... 4-5
Steering shaft, lubricating ............................................. 8-40
Storage ........................................................................... 9-2
Storage compartment ................................................... 4-18TTail/brake light bulb, replacing ..................................... 8-47
Throttle cable free play, adjusting ................................ 8-28
Throttle lever ........................................................... 4-9, 5-4
Tire pressure, measuring ............................................... 5-5
Tires ............................................................................... 5-4
Tire wear limit ................................................................. 5-6
Troubleshooting ........................................................... 8-49
Troubleshooting chart .................................................. 8-50VValve clearance ............................................................ 8-28
V-belt case drain plug .................................................. 8-26
V-belt cooling duct check hose .................................... 8-25
Vehicle identification number ....................................... 11-1WWheel hub bearings, checking ..................................... 8-39
U4S262E0.book Page 2 Tuesday, June 10, 2008 11:40 AM