2009 VOLVO S60 fog light

02 Instruments and controls
Instrument overview
0249
G029581
1
Front fog lights
60
2
Headlights/Parking lights/
switch for unlocking fuel filler
door
59
3
Rear fog light
4
Turn signals/High/low beams
62
5
Cruise control
67
6
Horn
-
7
Instrument panel
50
8
Audio controls in steering
wheel
221
9
Windshield wipers
64
10
Parking brake (hand brake)
69
11
Center console buttons
56
12
Climate control
86
13
Audio system
216
14
12-V socket
57,
71
15
Hazard warning flashers
66
16
Glove compartment
101
17
Panel vents
88
18
Text display
50
19
Temperature gauge
50
20
Odometer/Trip odometer/
Cruise control indicator
50
21
Speedometer
50
22
Turn signal indicators
50
23
Tachometer
50
24
Ambient temperature/Clock/
Selected gear indicator
50
25
Fuel gauge
50
26
Indicator and warning sym-
bols
52
27
Panel vents
88
28
Instrument lighting
60
29
Not in use
30
Lighting panel
59
31
Reading lights
97
32
Interior lighting
97
33
Moonroof control
76
34
Seat belt reminder
18
35
Rearview mirror
73
36
Lock button, for all doors
112
37
Cut-out button for rear seat
power windows
73
38
Controls, power windows
73
39
Controls, door mirrors
76

02 Instruments and controls
Indicator and warning symbols
02``53
If the BRAKE and ABS warning lights come
on at the same time, this could indicate a
fault in the brake system.
1. Stop the vehicle in a suitable place and
switch off the engine.
2. Restart the engine.
3. If both warning lights go off, no further
action is required.
4. If both lights are still on after the engine has
been restarted, switch off the engine again
and check the brake fluid level (see
page 193 for the location of the brake fluid
reservoir).
5.
If the brake fluid level is above the MIN
mark, drive carefully to a trained and quali-
fied Volvo service technician and have the
brake system inspected.
WARNING
If the fluid level is below the MIN mark in the
reservoir or if a "
Brake failure - Service
urgent
" message is displayed in the text
window:DO NOT DRIVE. Have the vehicle
towed to a trained and qualified Volvo serv-
ice technician and have the brake system
inspected.
PARK BRAKE - Parking brake appliedThis light will be on when the parking brake
(hand brake) is applied. The parking brake lever
is situated between the front seats. For addi-
tional information, see page 71.
Canadian models are equipped
with this symbol.Low oil pressure
2
If the light comes on while driving,
stop the vehicle and then stop the
engine immediately and check the
engine oil level, see page 191.
If the light stays on after restart, have the vehi-
cle towed to the nearest trained and qualified
Volvo service technician. After hard driving, the
light may come on occasionally when the
engine is idling. This is normal, provided it goes
off when the engine speed is increased.Generator warning light
If the light comes on while the
engine is running, have the charg-
ing system checked.
Rear fog light
This light indicates that the fog
light is on.
CHECK ENGINE - Malfunction indicator
lightOn-Board Diagnostics II (OBDII): As you drive,
a computer called "OBDII" monitors your vehi-
cle's engine, transmission, electrical and emis-
sion systems. The CHECK ENGINE light will
light up if the computer senses a condition that
potentially may need correcting. When this
happens, please have your vehicle checked by
a trained and qualified Volvo service technician
as soon as possible.
ACHECK ENGINE light may have many cau-
ses. Sometimes, you may not notice a change
in your vehicle's behavior. Even so, an uncor-
rected condition could hurt fuel economy,
emission cleanliness, and driveability.
Extended driving without correcting the cause
could even damage other components in your
vehicle.
Canadian models are equipped
with this warning light.
2On certain engines, the symbol for low oil pressure is not used. Instead, a text warning is provided in the information display.

02 Instruments and controls
Lighting panel
02``59
3501866mG027132
Headlight/parking light switchFront fog lightsRear fog lightInstrument panel lightingFuel filler door unlock button
Parking lightsThe front and rear parking lights can be turned
on even when the ignition is switched off.•
Turn switch (1) to position
.
The license plate lights also illuminate when the
parking lights are switched on.
Headlights±
Turn the ignition key to position II.
The low beam headlights (daytime running
lights) illuminate automatically, except when
the light switch (1) is in position.
1
See page 62 for information on switching
between high and low beams.
NOTE
Active Bi-Xenon headlights (option): Turn
the headlight switch to position 0 to activate
a daylight sensor, which automatically
switches the low beams on or off, depend-
ing on ambient light conditions. When driv-
ing in daylight, the headlights will switch off
and the daytime running lights will come on.
In darkness, the daytime running lights will
switch off and the Active Bi-Xenon head-
lights will switch on.
Active Bi-Xenon headlights (ABL) -
option
G020789
Active Bi-Xenon headlight beamsWhen the ABL function is activated, the head-
light beams adjust laterally to help light up a
curve according to movements of the steering
wheel (see the right-pointing beam in the illus-
tration above).
This function is activated automatically when
the engine is started and can be deactivated/
reactivated by pressing the ABL button (see
page 57).
1On Canadian models, the daytime running lights will remain on with the light switch in this position.

02 Instruments and controlsLighting panel
0260
Fog lightsFront fog lights (option)The front fog lights can be used in combination
with either the headlights or the parking lights.•
Turn the ignition key to position II.
•
Press button 2 to turn on the front fog
lights.
An indicator light in the button illuminates when
the front fog lights are on.
Rear fog lightThe single rear fog light is located in the driver's
side tail light cluster.
The rear fog light will only function in combi-
nation with the high/low beam headlights or the
optional front fog lights.•
Turn the ignition key to position II.
•
Press button 3 to turn on the rear fog light.
An indicator light in the button illuminates when
the rear fog light is on.NOTE
The rear fog light is considerably brighter
than the normal taillights and should be
used only when conditions such as fog, rain,
snow, smoke or dust reduce visibility for
other vehicles to less than 500 ft.
(150 meters).
Instrument panel lightingThe instrument panel lighting illuminates when
the ignition key is in position IIand the light
switch (1) is in either position
or
.
•
Move the thumb wheel (4) up to increase
brightness or down to decrease bright-
ness.
Unlocking the fuel filler doorPress button 5 when the vehicle is at a stand-
still to unlock the fuel filler door. Please note
that the fuel filler door will remain unlocked until
the vehicle begins to move forward. An audible
click will be heard when the fuel filler door
relocks.
NOTE
If the fuel filler door does not unlock after the
button has been pressed, drive the vehicle
at a speed of at least 5 mph (8 km/h), stop
the vehicle, and press the button again.See page 61 for information on unlocking the
fuel filler door manually.

03 ClimateClimate control systems - general information
0386
Condensation on the inside of the
windowsThe defroster function should be used to
remove fog or mist from the inside of the win-
dows. Keeping the windows clean with a com-
mercially available window washing spray will
also help prevent fogging or misting.Ice and snowAlways keep the air intake grille at the base of
the windshield free of snow.Cabin air filterReplace the cabin air filter with a new one at
the recommended intervals. Please refer to
your Warranty and Service Records Informa-
tion booklet, or consult a trained and qualified
Volvo service technician for these intervals.
The filter should be replaced more often when
driving under dirty and dusty conditions. The
filter cannot be cleaned and therefore should
always be replaced with a new one.
SensorsThe sunlight sensor on the dashboard and pas-
senger compartment temperature sensor in
the ECC control panel should not be covered
in any way as this could cause incorrect infor-
mation to be sent to the ECC system.Parking the vehicle in warm weatherIf your vehicle has been parked in the sun in
warm weather, opening the windows and
moonroof (option) for several minutes before
driving will help release the warm air from the
passenger compartment. When the engine is
running, close the windows and moonroof and
use the recirculation function for several
minutes to enable the air conditioning to cool
the compartment as quickly as possible.Windows and optional moonroofThe ECC system will function best if the win-
dows and optional moonroof are closed. If you
drive with the moonroof open, we recommend
that you manually adjust the temperature and
blower control (the LED in the AUTO switch
should be off).
AccelerationThe air conditioning is momentarily disen-
gaged during full-throttle acceleration.Climate control maintenanceSpecial tools and equipment are required to
maintain and carry out repairs on the climate
system. Work of this type should only be done
by a trained and qualified Volvo service tech-
nician.RefrigerantVolvo cares about the environment. The air
conditioning system in your vehicle contains a
CFC-free refrigerant - R134a (HFC134a). This
substance will not deplete the ozone layer. The
system contains 1.5 lbs (700 g) R134a and
uses PAG oil.Climate system blowerThe climate system blower will be automati-
cally switched off when the engine is not run-
ning (even if the ignition key is in position Ior
II) to avoid unnecessary battery drain. To acti-
vate the blower, turn the control to the desired
setting.

03 ClimateElectronic climate control, ECC
0390
Blower control
Turn the control clockwise to
increase or counterclockwise
to decrease the blower
speed. Pressing the AUTO
switch will automatically reg-
ulate blower speed and over-
ride manual adjustment.
Turning the blower control counterclockwise
until an orange LED comes on will turn both the
blower and the air conditioning off.Air distributionAir flow to windows
Air through panel vents
Air through floor vents
G027267
PressAUTO to automatically regulate air flow
or press any combination of the controls
shown in the illustration to manually adjust air
flow. An LED in the switch will light up if an air
flow control has been pressed.Heated front seats (option)•
Press the switch once for maximum seat
heating. Both LEDs in the switch will be lit.
•
Press the switch a second time for comfort
heating. One LED in the switch will be lit.
•
Press the switch a third time to turn the
heating off completely. The LED will go off.
The seat heating for the passenger seat should
be switched off when the seat is not occupied.
A/C - ON/OFF
Press the switch to turn the air
conditioning on or off. The
"ON" or "OFF" LED will light up
to indicate if the system is
switched on or off. Other func-
tions will still be regulated auto-
matically (if the AUTO switch is on).
•
The air conditioning functions only at tem-
peratures above 32 °F (0 °C).
•
While the Defroster function is selected,
the air conditioning is temporarily activated
to dehumidify the air, even if you have man-
ually switched the air conditioning off. This
will only function if the blower is not
switched off.
Recirculation
Press this switch to engage the
recirculation function (air in the
passenger compartment recir-
culates - no fresh air enters the
compartment). The LED in the
switch will light up to indicate
that the function is engaged.
MANAUT€
Use this function if the outside air is con-
taminated with exhaust gases, smoke, etc
or to heat/cool the vehicle quickly.
€
Recirculation should not be used for more
than 15 minutes. If your windows begin to
fog or mist, make sure that the recirculation
function is switched off.
€
SelectingDefroster automatically
switches recirculation off.

03 Climate
Electronic climate control, ECC
0391
•
Timer mode activation: (vehicles with the
Interior Air Quality system have no timer
mode) Press and hold the recirculation but-
ton for at least 3 seconds to activate a
recirculation timer mode. The amber LED
in the recirculation button will flash 5 times
to show that the timer mode is being acti-
vated. In timer mode, each time the recir-
culation button is pressed, the climate
control system will recirculate the air in the
passenger compartment for 5-12 minutes,
depending on the outside air temperature,
and then revert back to fresh air.
•
Timer mode deactivation: Press and hold
the recirculation button for 3 seconds. The
amber LED in the recirculation button will
illuminate steadily for 5 seconds to show a
return to "normal" mode.
•
In normal mode, when the recirculation
button is pressed, the climate control sys-
tem will recirculate the air in the passenger
compartment until the recirculation button
is pressed again.
•
Timer mode memory: If the vehicle is
turned off while timer mode is active, timer
mode will still be active when the vehicle is
restarted.
Interior air quality sensor (option)
Some vehicles are equipped
with a multifilter and air quality
sensor. The filter separates
gases and particles, thereby
reducing the amounts of odors
and contaminants entering the
vehicle. The air quality sensor detects
increased levels of contaminants in the outside
air. When the air quality sensor detects conta-
minated outside air, the air intake closes and
the air inside the passenger compartment is
recirculated, i.e. no outside air enters the vehi-
cle. The filter also cleans recirculated passen-
ger compartment air.
MANAUTWhen the ECC system is in the AUTO mode,
the green LED in the button will be on.Operation±
PressAUTO to operate the air quality sen-
sor (normal setting).
or
±
Select one of the following three functions
by pressing the recirculation button 1, 2 or
3 times.
1.
The AUT LED lights. The air quality sensor
is now activated.2. No LED lights. Recirculation is not acti-
vated unless needed to cool the passenger
compartment in a warm climate.
3.
TheMAN LED lights. Recirculation is now
activated.
Keep in mind the following•
Make it a rule to have the air quality sensor
activated at all times.
•
Recirculation is limited in cold climates to
avoid fogging.
•
If window fogging occurs, you should
deactivate the air quality sensor.
•
If fogging occurs, use the defroster func-
tions for the windshield, side windows and
rear window, see page 66.
The filter should be changed at the intervals
recommended in the service schedule. How-
ever, if the vehicle is used in a severely conta-
minated environment, it may be necessary to
change the filter more frequently.

08 Car care
Washing and cleaning the vehicle
08``177
NOTE
When washing the vehicle, remember to
remove dirt from the drain holes in the doors
and sills
WARNING
When the vehicle is driven immediately after
being washed, apply the brakes several
times in order to remove any moisture from
the brake linings.
Engine cleaning agents should not be used
when the engine is warm. This constitutes a
fire risk.Automatic washing - simple and quick•
We do NOT recommend washing your
vehicle in an automatic wash during the
first six months (because the paint will not
have hardened sufficiently).
•
An automatic wash is a simple and quick
way to clean your vehicle, but it is worth
remembering that it may not be as thor-
ough as when you yourself go over the
vehicle with sponge and water. Keeping
the underbody clean is most important,
especially in the winter. Some automatic
washers do not have facilities for washing
the underbody.
•
Before driving into an automatic vehicle
wash, make sure that side view mirrors,auxiliary lamps, etc, are secure, and that
any antenna(s) are retracted or removed.
Otherwise there is risk of the machine dis-
lodging them.
Exterior lightingCondensation may form temporarily on the
inside of the lenses of exterior lights such as
headlights, fog lights, or tail lights. This is nor-
mal and the lights are designed to withstand
moisture. Normally, condensation will dissi-
pate after the lights have been on for a short
time.Polishing and waxing•
Normally, polishing is not required during
the first year after delivery, however, wax-
ing may be beneficial.
•
Before applying polish or wax the vehicle
must be washed and dried. Tar spots can
be removed with kerosene or tar remover.
Difficult spots may require a fine rubbing
compound.
•
After polishing use liquid or paste wax.
•
Several commercially available products
contain both polish and wax.
•
Waxing alone does not substitute for pol-
ishing a dull surface.
•
A wide range of polymer-based vehicle
waxes can be purchased today. Thesewaxes are easy to use and produce a long-
lasting, high-gloss finish that protects the
bodywork against oxidation, road dirt and
fading.
•
Do not polish or wax your vehicle in direct
sunlight (the surface of the vehicle should
not be warmer than 113 ° F (45 ° C).CAUTION
Volvo does not recommend the use of long-
life or durable paint protection coatings,
some of which may claim to prevent pitting,
fading, oxidation, etc. These coatings have
not been tested by Volvo for compatibility
with your vehicle's clear coat. Some of them
may cause the clear coat to soften, crack,
or cloud. Damage caused by application of
paint protection coatings may not be cov-
ered under your vehicle's paint warranty.Cleaning the upholsteryFabricClean with soapy water or a detergent. For
more difficult spots caused by oil, ice cream,
shoe polish, grease, etc., use a clothing/fabric
stain remover. Consult your Volvo retailer.Interior plastic componentsCleaning interior plastic components should
be done with a cleaning agent specially