2009 VOLVO S60 brake

02 Instruments and controls
Indicator and warning symbols
02``53
If the BRAKE and ABS warning lights come
on at the same time, this could indicate a
fault in the brake system.
1. Stop the vehicle in a suitable place and
switch off the engine.
2. Restart the engine.
3. If both warning lights go off, no further
action is required.
4. If both lights are still on after the engine has
been restarted, switch off the engine again
and check the brake fluid level (see
page 193 for the location of the brake fluid
reservoir).
5.
If the brake fluid level is above the MIN
mark, drive carefully to a trained and quali-
fied Volvo service technician and have the
brake system inspected.
WARNING
If the fluid level is below the MIN mark in the
reservoir or if a "
Brake failure - Service
urgent
" message is displayed in the text
window:DO NOT DRIVE. Have the vehicle
towed to a trained and qualified Volvo serv-
ice technician and have the brake system
inspected.
PARK BRAKE - Parking brake appliedThis light will be on when the parking brake
(hand brake) is applied. The parking brake lever
is situated between the front seats. For addi-
tional information, see page 71.
Canadian models are equipped
with this symbol.Low oil pressure
2
If the light comes on while driving,
stop the vehicle and then stop the
engine immediately and check the
engine oil level, see page 191.
If the light stays on after restart, have the vehi-
cle towed to the nearest trained and qualified
Volvo service technician. After hard driving, the
light may come on occasionally when the
engine is idling. This is normal, provided it goes
off when the engine speed is increased.Generator warning light
If the light comes on while the
engine is running, have the charg-
ing system checked.
Rear fog light
This light indicates that the fog
light is on.
CHECK ENGINE - Malfunction indicator
lightOn-Board Diagnostics II (OBDII): As you drive,
a computer called "OBDII" monitors your vehi-
cle's engine, transmission, electrical and emis-
sion systems. The CHECK ENGINE light will
light up if the computer senses a condition that
potentially may need correcting. When this
happens, please have your vehicle checked by
a trained and qualified Volvo service technician
as soon as possible.
ACHECK ENGINE light may have many cau-
ses. Sometimes, you may not notice a change
in your vehicle's behavior. Even so, an uncor-
rected condition could hurt fuel economy,
emission cleanliness, and driveability.
Extended driving without correcting the cause
could even damage other components in your
vehicle.
Canadian models are equipped
with this warning light.
2On certain engines, the symbol for low oil pressure is not used. Instead, a text warning is provided in the information display.

02 Instruments and controlsIndicator and warning symbols
0254
ABS (Anti-lock brake system)
If the warning light comes on, there
is a malfunction of the ABS system
(the standard braking system will
still function). The vehicle should
be driven to a trained and qualified
Volvo service technician for inspection. For
additional information, see page 135.
Dynamic Stability Traction Control
(DSTC) system
This indicator light will flash when
DSTC is actively working to stabi-
lize the vehicle. For more detailed
information, see page 138.
Tire pressure monitoring light
See page 172 for more informa-
tion on this function.
Turn signal indicator - trailer (certain
models)
If you are towing a trailer, this light
will flash simultaneously with the
turn signals on the trailer. If the
light does not flash when signaling,
neither the trailer's turn signals nor
the vehicle's turn signals are functioning.
Messages in the text window
G026979
When a warning light in the instrument panel
comes on, a message is also displayed in the
text window. After you have read the message,
you can erase it by pressing button A (see illus-
tration).
NOTE
Certain messages cannot be erased until
the condition has been corrected.If a warning message is displayed when e.g.
you are using the trip computer, this messagemust be erased before you can access the
function of your choice. Press button A to erase
the warning message.
You can scroll through the stored messages by
pressing button A (see illustration). The text
window can be cleared (the message will be
returned to memory) by pressing button A
again.

02 Instruments and controls
Cruise control
02``69
G027177
The cruise control panel is located on the left
side of the steering wheel hub and may differ
in appearance, depending on the model.Engaging cruise control±
Press the CRUISE button.
>
CRUISE will be displayed in the infor-
mation window in the instrument panel.
NOTE
This does not set the vehicle's speed.Setting speed±
Press+ or – to set the current speed.>
CRUISE-ON
will be displayed in the
information window in the instrument
panel.
G027139
Increasing or decreasing speedUse+ or – in the following ways to increase or
decrease the vehicle's speed•
Press and hold down + or – until the vehicle
reaches the desired speed.
•
Press+ or – for approximately a half sec-
ond and release the button to increase or
decrease vehicle speed by approximately
1 mph (1.6 km/h).
NOTE
Cruise control will not function at speeds
below approximately 20 mph (30 km/h).Braking•
Cruise control is automatically disengaged
when the brake pedal is depressed. The
currently set speed is stored in memory.
•
Pressing resume (see illustration) will
return the vehicle to the previously set
speed.
AccelerationMomentary acceleration, such as when pass-
ing another vehicle, does not affect cruise con-
trol operation. The vehicle will automatically
return to the previously set speed when you
release the accelerator pedal.Disengaging cruise controlTo disengage cruise control:
±
Press the CRUISE button.
>
CRUISE
or
CRUISE-ON
will no longer
be displayed in the information window
in the instrument panel.

02 Instruments and controlsCruise control
0270
NOTE
Cruise control is automatically disengaged
if:•
the engine is switched off
•
the gear selector is placed in (N)eutral
•
the wheels start to spin or lock
•
if an increase in speed is maintained for
more than one minute
•
if the vehicle's speed falls below
approximately 20 mph (30 km/h).
Temporarily disengaging cruise control1.
Press0 to temporarily disengage cruise
control.
>
CRUISE
will be displayed in the infor-
mation window in the instrument panel.
2. Press the brake pedal.
Press resume (see illustration) to return to the
previously set speed.
WARNING
Cruise control should not be used in heavy
traffic or when driving on wet or slippery
roads, or when driving on unpaved or
uneven road surfaces. Cruise control may
not maintain set speed on steep down-
grades.

02 Instruments and controls
Parking brake
0271
G033050
The parking brake lever is located between the
front seats.
NOTE
The indicator light will light up even if the
parking brake has only been partiallyap-
plied.When applying the parking brake1. Press firmly on the brake pedal.
2. Pull the parking brake lever up firmly to its
full extent.
3. Release the brake pedal and ensure that
the vehicle is at a standstill.4. If the vehicle rolls, the parking brake lever
must be pulled more firmly.
5. When parking a vehicle always put the gear
selector in first gear (for manual transmis-
sion) or P (for automatic transmission).
Parking on a hill•
If the vehicle is pointing uphill, turn the front
wheels so that they point away from the
curb.
•
If the vehicle is pointing downhill, turn the
front wheels so that they point toward the
curb.
Releasing the parking brake1. Press firmly on the brake pedal.
2. Pull the lever up slightly, press the button
at the end of the lever and lower the lever
completely.
WARNING
Pull up the parking brake lever up firmly to
its full extent.

04 InteriorFront seats
0494
Manually adjusted front seats
G027214
1. Front-rear adjustment: lift the bar and
move the seat to the position of your
choice.
2. Raise/lower the front edge of the seat
cushion (option): use the control to pump
the front edge of the cushion up or down.
3. Raise/lower seat height: pump the seat up
or down.
4. Lumbar support: turn the control for firmer
or softer lumbar support.
5. Backrest tilt: turn the control to adjust the
angle of the backrest.6. Control panel for optional power seat (see
page 94 for more information).
WARNING
Do not adjust the seat while driving. The
seat should be adjusted so that the brake
pedal can be depressed fully. In addition,
position the seat as far rearward as comfort
and control allow.
Check that the seat is securely locked into
position after adjusting.Folding the backrests in the front seat
G014805
The front passenger seat backrest can be
folded to a horizontal position to make room for
a long load. Fold the backrest as follows:•
Move the seat as far back as possible.
•
Adjust the backrest to the upright position.
•
Lift the catches on the rear of the backrest.
•
Without releasing the catches, push the
backrest forward.
•
Move the seat as far forward as possible
so that the head restraint slides under the
glove compartment.WARNING
Cover sharp edges on the load to help pre-
vent injury to occupants. Secure the load to
help prevent shifting during sudden stops.Power seat - (option on certain models)OperationDriver's seat: The seat can be adjusted if the
ignition key is in position I, II or if the engine is
running. It can also be adjusted as follows with
the ignition off:

04 InteriorFront seats
0496
WARNING
•
Because the driver's seat can be
adjusted with the ignition off, children
should never be left unattended in the
vehicle.
•
Movement of the seat can be STOPPED
at any time by pressing any button on
the power seat control panel.
•
Do not adjust the seat while driving. The
seat should be adjusted so that the
brake pedal can be depressed fully. In
addition, position the seat as far rear-
ward as comfort and control allow.
•
The seat rails on the floor must not be
obstructed in any way when the seat is
in motion.
Programming the memory (option)
G027037
Three different seating and door mirror posi-
tions can be stored in the driver seat's memory.
The following example explains how button 1
can be programmed. Buttons 2 and 3 can be
programmed in the same way.
To program (store) a seat position in button 1:
1. Move the seat to the desired position using
the seat adjustment controls (see
page 95).
2.
Press and hold down the MEM (memory)
button.3.
With the MEM button depressed, press
button 1 briefly to store the seat's current
position.
To move the seat to the position that it was in
when button 1 was programmed:
Press and hold down button 1 until the seat
stops moving.
As a safety precaution, the seat will stop auto-
matically if the button is released before the
seat has reached the preset position.

04 InteriorRear seat and trunk
04102
Folding the rear seat backrest
8503282m
G027327
Backrest release handles in trunkBoth rear seat backrests can be folded down,
together or individually to enable you to trans-
port long objects.
Fold the rear seat backrests as follows:
1. Check first that the head restraint is folded
down.
2. Pull the handle in the cargo compartment
as shown in the illustration.
3. Fold the backrest down.
G028003
WARNING
Keep vehicle doors and the luggage com-
partment locked and keep keys out of a
child's reach. Unsupervised children could
lock themselves in an open trunk and risk
injury. Children should be taught not to play
in vehicles.
On hot days, the temperature in the trunk or
vehicle interior can rise very quickly. Expo-
sure of people to these high temperatures
for even a short period of time can cause
heat-related injury or death. Small children
are particularly at risk.
WARNING
•
When the backrest is returned to the
upright position, check that it is properly
locked in place. Return the head
restraints to the upright position.
•
Long loads should always be securely
anchored to help avoid injury in the
event of a sudden stop.
•
Always turn the engine off and apply the
parking brake when loading/unloading
the vehicle.
•
Place the transmission in the P position
(automatic transmission) to help pre-
vent inadvertent movement of the gear
selector.
•
The vehicle features a 60/40 split fold-
down rear seat. This function is per-
formed by handles inside the trunk, and
also provides a means for children and
adults to enter the passenger compart-
ment in the event they become locked
inside the trunk.
•
Adults are advised to familiarize them-
selves with the operation and location
of the release handles.
•
To fold down the rear seats from inside
the trunk, pull the release control han-
dles located on either side of the trunk.