2009 TOYOTA LAND CRUISER reset

3
OVERVIEW
FEATURES/OPERATIONS
SAFETY AND EMERGENCY FEATURES
CD INRAND RPTSCAN ALBDISC FLD ART TR FILE ST MEG TRAFPLDGNPAUTO-P ART4 DISC OF OWNER
TYPE∑DISCAM-GAT
SCAN
FMDISC∑AUXTRAF
00 H
M
LOADTUNE·FILE
CH-DISCFMTA P EPWR·VOL
SEEK-TRACKDISC·AUXSAT
AM4 DISC OF OWNER
SCAN
LOGIC CONTROL DECK
SECURITYCLIMATE
DEST MAVOICEP
MENU
DISP
INFO
A UDIO
Four-wheel drive control switch
VSC/TRAC OFF switch
Center differential lock/unlock switch
Cruise control
Tire Pressure Warning System reset
Power rearview mirror control
Instrument panel light control
Tilt and telescopic steering control
Roll Sensing of Curtain shield Airbag OFF switch
Toyota park assist switch
1
115V AC Power outlet main switch
Headlight cleaner1
1
If equipped2Vehicles with navigation system: for details, refer to the “ Navigation
System Owner’s Manual .”
Without navigation system
With navigation system
M2.qxd 7/28/08 3:14 PM Page 3

4
OVERVIEW
Indicator symbols
Instrument cluster
Tachometer
Engine coolant temperature
Fuel gauge
Speedometer
Service indicator and reminder
Vo l t m e t e r
Multi-information display
Automatic Transmission shift range display
Odometer and two trip meters
Engine oil pressure gauge
Odometer/Trip meter and trip meter reset button
Charging system warning1
Brake system warningAIR BAG ON and AIR BAG OFF indicator
1
Driver seat belt reminder
(alarm will sound if speed is over 12 mph)Front passenger seat belt reminder
(alarm will sound if speed is over 12 mph)
Pre-Collision System warning light1
Malfunction/Check Engine indicator1
For details, refer to “Indicators and warning lights,” Section 2-2\
, 2009
Owner’s Manual .
M2.qxd 7/28/08 3:14 PM Page 4

20
FEATURES/OPERATIONS
Audio
RADIO
To preset stations Tune in the desired station and hold down a preset
button (1-6) until you hear a beep. Push desired preset button (1-6)\
to
select.
To scan stations Push and hold “SCAN” to scan preset stations. Push again
to hold selection.
CD PLAYER
To scan tracks on a disc Push and hold “SCAN.” Push again to hold
selection.
CD changer
-To load one disc Push “LOAD” and insert one disc.
-To load multiple discs Push and hold “LOAD” until you hear a beep.
Insert one disc. Shutter will close and then re-open for next disc.
To select a file (MP3/WMA only) Turn “TUNE.
FILE.”
To select a folder (MP3/WMA only) Push the preset button “5” or “6.”
AUX audio jack
Eject CD
Push to
turn
ON/OFF Load CD(s)
Seek station/
CD track select
Station/CD
track scan
Mode Traffic information
Preset buttons - functions in other
modes indicated above number
View CD
text
Push to skip
up/down CD and
radio category type
Push to
adjust tone
& balance
AUXBy inserting a mini plug into
the AUX audio jack, you can
listen to music from a portable
audio device through the
vehicle’s speaker system while
in AUX mode.
M2.qxd 7/28/08 3:14 PM Page 20

21
OVERVIEW
FEATURES/OPERATIONS
SAFETY AND EMERGENCY FEATURES
“ ”
-In radio modePush to select a preset station; push and hold to seek
the next strong station.
-In CD mode Push to skip up or down to next/previous track.
“MODE”
Push to turn audio ON and to select an audio mode. Push and hold to
turn audio system OFF.vv
Steering wheel switches
MODE
Volume control
Rear seat entertainment system
(if equipped)
PHONE VOL
PHONE VIDEO MONOLVOLRAC1
15
V10 0W
Front audio system (DVD player)
DVD screen
Remote control
Headphone volume control and headphone jacks
A/V input adapter
115V AC Power outlet
For details, refer to the “ Navigation System Owner’s Manual .”
M2.qxd 7/28/08 3:14 PM Page 21

28
SAFETY AND
EMERGENCY FEATURES
If belt is fully extended, then retracted even slightly, it cannot be
re-extended beyond that point, unless fully retracted again. This featur\
e
is used to help hold child restraint systems securely.
To find more information about seat belts, and how to install a child
restraint system, refer to the Owner's Manual.
Keep as low on
hips as possible
Take up slack
Too high
Seat belts
Push up, or squeeze
lock release to lower
System reset initialization
1. Push and hold “ SET” button
until the indicator blinks
three times.
2. Wait a few minutes to allow initialization to complete.
Seat belts-Shoulder belt anchor
After adjusting tire pressures, or after tires have been rotated or
replaced, turn the ignition switch to “ON” and press and hold the \
“ SET” button until indicator blinks three times. Let the vehicle sit f\
or a
few minutes to allow initialization to complete.
Refer to the load label on the door jamb or the Owner’s Manualfor tire
inflation specifications.
If the tire pressure indicator flashes for more than 60 seconds and then\
remains on, take the vehicle to your local Toyota dealer.
Note : The warning light may come on due to temperature changes or
changes in tire pressure from natural air leakage. If the system has not\
been initialized recently, setting the tire pressures to factory
specifications should turn off the light.
Tire Pressure Monitoring (warning)
System
M2.qxd 7/28/08 3:14 PM Page 28