2009 SKODA SUPERB ESP

Communication
147
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Other possible commandsEnter PIN codeA PIN code must be entered before operating the system. – Press the PTT button.– Give the command
ENTER PIN/PIN CODE
after the signal tone.
After this command the PIN code can be entered. The entry of the PIN code is only possible if:•
the ignition is switched on,
•
the mobile phone is in the mount,
•
the mobile phone is switched on.
The digits
zero to nine
are permitted. The system detects no continuous digit
combinations such as twenty-three, but only individually spoken digits (two, three). After each order of digits (separation through brief voice pause) the detected digits are repeated. Notes for entering the PIN code•
When entering a PIN code with more than 8 digits, the system indicates “
The
PIN is too long
”.
•
When entering an incorrect PIN code, the system indicates “
The PIN is incor-
rect
”.
•
If the incorrect PIN code has been entered three times consecutively, the card
is blocked. With the aid of the personal
unblocking code PU
K (Personal Unblock
Key), the SIM card can be unblocked.
The unblocking code can only be entered
via the phone keypad and not through the voice control. Example for entering the PIN code You can interrupt the dialogue at any time
by pressing the PTT
button or with the
voice command
CANCEL
.
Dial number– Press the PTT button.
Voice command
Activity
DIAL
The telephone number is selected.
STORE
In addition to the name in the phone book, which is selected on the information display, a voice recording is stored to select with the help of the voice com- mands or the entered PIN code.
REPEAT
The entered name or the digits are repeated. Then the system requests with voice response “
please pro-
ceed
” the entry of further digits or commands.
BACK
The entered name or the last entered order of digits is erased. Previously entered groups of digits are repeated. Then the system requests with voice response “
please proceed
” the entry of further digits
or commands.
DELETE
All entered digits are erased. Then the system requests with voice response “
The number is
deleted. The number please
” the entry of further
digits or commands.
CANCEL
The dialogue is ended.
Voice command
Announcement
ENTER PIN/PIN CODE
“ The PIN please
”.
e.g.
ZERO ONE TWO THREE
“Zero One Two Three
”.
If no entry is put in, the following anno
uncement is made after about 5 seconds.“Possible commands are: store, repeat, correct, delete or more digits
”.
STORE
“The PIN is saved
”.
(end of dialogue)
s2dk.1.book Page 147 Wednesday, April 8, 2009 12:23 PM

Communication
150
You can interrupt the dialogue at any time
by pressing the PTT button or with the
voice command
CANCEL
.
If the user answers with
NO
, the system answers with “
Cancel
” and the dialogue is
ended.Delete voice phonebook– Press the PTT button. – Give the command
DELETE PHONEBOOK
after the signal tone.
After giving this command there is the
possibility to erase the complete phone
voice phone book or the individually stored names out of the phone phone book. Example for erasing the complete phonebook You can interrupt the dialogue at any time
by pressing the PTT button or with the
voice command
CANCEL
.
Example for erasing individual names out of the phone phonebook As long as the phonebook is read out, ot
her entries can be erased by pressing the
PTT button. You can end the dialogue at an
y time with the voice command
CANCEL
.
Listening-in to the phonebook– Press the PTT button. – Give the command
LISTEN TO/PLAY PHONEBOOK
after the signal
tone.
After giving this command the phone voic
e phone book is read out by the system.
By pressing the PTT button when announ
cing the desired name, the corresponding
telephone number is being dialed; the system answers: “
The number is being
dialed
”.
Voice command
Announcement
DELETE PHONEBOOK
“Do you want to delete the whole phonebook?
”.
If no entry is put in, the following a
nnouncement is made af
ter about 5 seconds.
“Possible commands are: yes, no, repeat
”.
YES
“Are you sure?
”.
YES
“The phonebook is deleted
”.
Voice command
Announcement
DELETE PHONEBOOK
“Do you want to delete the whole phonebook?
”
If no entry is put in, the following anno
uncement is made after about 5 seconds.“Possible commands are: yes, no, repeat
”.
NO
The phonebook is read out.
When announcing the entry to be erased, press the PTT button.
“ Do you want to delete (name)?
”
If no entry is put in, the following anno
uncement is made after about 5 seconds.“Possible commands are: yes, no
”.
YES
“The name is deleted
”.
Continue reading out the phone book.
s2dk.1.book Page 150 Wednesday, April 8, 2009 12:23 PM

Communication
151
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Universal telephone preinstallation GSM III*IntroductionThis enables you to make full use of the
advantages of a norm
al carphone (“hands-
free system” using a microphone integrated in the vehicle, optimal transmission of signals using an external aerial etc.). The equipment includes also the voice control. The telephone is connected using the
rSAP
profile -
Remote SIM access profile
(telecommunication of the SIM data)
by means of Bluetooth
® technology, if your
telephone supports this profile. The equipment includes the following functions:•
Display of the SMS text in the information display.
•
Free talking in the vehicle interior.
•
MUTE signal to the radio.
•
Voice control (with the set-up possibility for “short and long dialogue”,
depending on the user's knowledg
e of the operating structure).
•
Convenience mode with the multifunction
steering wheel and the display in the
information display.•
Handsfree-system.
The voice control of the telephone is acti
vated by pressing the button PTT on the
multifunction st
eering wheel
⇒page 153, fig. 157
.
A phone phonebook is part of the univers
al telephone preinstallation GSM III with
voice control. In the phone phonebook ther
e are 1000 free memory locations avail-
able. This phone phonebook is independent of the appliance used for the mobile phone. Furthermore the volume can be changed indi
vidually at any time with the button
for setting the radio or on vehicles fitted with multifunction steering wheel* with function buttons on
the steering wheel.
Dialogue The period, in which the telephone system is ready to receive voice commands and carry out the voice commands, is called DIALOGUE. The system gives audible feed-back and guides you if necessary through
the relevant functions. You can start or
end the dialogue at any time by pressing the PTT button.
The dialogue is always automatically ended after carrying out an operation, e.g. after erasing the name from the phonebook. The dialogue of the incoming call is im
mediately interrupted and you can accept
the call by pressing the button
.
If a voice command is not detected, the system answers with “
Sorry?
” and a new
entry can be performed. After the 2nd error the system repeats the aid. After the 3rd error the answer “
Cancel
” is given and the dialogue is ended.
Optimum understanding of the voice commands depends on the following factors:•
Speak with a normal tone of voice without intonation and excessive voice
pauses.•
Avoid insufficient articulation.
•
Close the doors, windows and sliding roof, in order to reduce or stop disturbing
exterior noise.•
It is recommended to speak louder at higher speeds, so that the tone of your
voice is louder than the increased surrounding noise.•
During the dialogue avoid additional noise in the vehicle, e.g. simultaneously
talking occupants.•
Do not speak, if the system makes an announcement.
•
The microphone for voice control is in
serted in the moulded headliner and
directed to the driver and front passenger. Therefore the driver and the front passenger can operate the equipment.
WARNING
Pay attention primarily to the traffic situation! As the driver you are fully responsible for road safety. Use the tele
phone system only to such an extent,
so that you are in full control of your vehicle at any time.
Note
•
Should you have any questions, please
contact an authorised Škoda Service
Par tner.
s2dk.1.book Page 151 Wednesday, April 8, 2009 12:23 PM

Communication
152
•
Please also refer to the additional instructions
⇒page 141, “Mobile phones
and two-way radio systems”.Bluetooth
®
The equipment enables the wireless connection to the control unit of a telephone with Bluetooth
® function which supports the
rSAP
profile.
Process of connection – Switch on the ignition. – If you have not switched on Bluetooth
® on your telephone, switch it
on.
– For certain mobile phones it is necessary to switch on first the
rSAP

function.
– Press the button
 on the multifunction steering wheel and select
device search
. The system searches mobi
le devices and shows these
in the information display*.
– Select your telephone in the information display by turning the hand-
wheel and select it by pressing the handwheel.
– Within 30 seconds enter in your
telephone the 16 digit PIN of your
control unit, which is indicated in the information display* and confirm it according to the instructions on the display of your tele- phone.
– If your SIM card is blocked by a PI
N code, enter the PIN of the SIM card
of your telephone. The telephone connects to the control unit (during the first connection you can only select in the information display* and when the vehicle is stationary, if the PIN should be stored).
– For the first storage of a new user follow the instructions in the infor-
mation display.
– To download the telephone book an
d the indentification data of the
SIM card into the new control
unit, confirm ag
ain the command
rSAP

in your mobile phone. The system reads the telephone book.
If you do not want to confirm the command
rSAP
during each connection of the
telephone to the control unit, then you mu
st carry out in the menu of the mobile
phone an authorization using the control unit. The telephone deregisters from the GSM network and only the control unit ensures the communication with the network. In th
e telephone only the interface for Blue-
tooth
® remains active. In this case, you can on
ly select to separate from the device,
switch off the Bluetooth
® connection or the number of the emergency call 112.
If the PIN was stored, an automatic select
ion and connection of the telephone take
place the next time the ignition is switch
ed. Check on your mobile phone if the
automatic connection was established. Connection terminated The connection of the handsf
ree-system is terminated by means of Bluetooth
®:
•
When removing the key from the ignition lock (during a telephone call, the
connection is disconnected).•
By switching off the Bluetooth
® in the mobile phone.
•
By selecting “separate telephone” in the menu of the mobile phone.
On vehicles which are fitted out with radio or
navigation at the factory, it is possible
to terminate the telephone call after removi
ng the key from the ignition lock by
pressing the icon on the touch-screen of the radio
14) or the navigation, see oper-
ating instructions for radio or for navigation.
WARNING
•
Pay attention primarily to the traffic situation! As the driver you are fully
responsible for road safety. Use the telephone system only to such an extent, so that you are in full control of your vehicle at any time - risk of accident!•
In the event of air transport, the Bluetooth
® function of the handsfree-
system must be switched
off by a specialist garage!
14)Does not apply for Radio Swing.
s2dk.1.book Page 152 Wednesday, April 8, 2009 12:23 PM

Communication
157
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Other possible commandsDial number– Press the button PTT
⇒
page 153, fig. 157
.
– Give the command
DIAL NUMBER
after the signal tone.
After giving this command, the system requests the entry of a telephone number. The telephone number can be entered as an interconnected spoken row of digits (complete number), in the form of order of digits (separation through a brief voice pause) or through individually spoken digi
ts. After each order of digits (separation
through brief voice pause) the
detected digits are repeated.
The digits
zero to nine
are permitted. The system
detects no continuous digit
combinations such as twenty-three, but only individually spoken digits (two, three). You can enter the selected number in rand
om digital blocks or as a whole number
at once. We recommend to enter the select
ed number in digital blocks to each
three digits. If you enter more than 20 digi
ts, the system announces: “
The number is too long
”.
For an international call you can enter the
symbol instead of the two zeros at the
beginning of the selected number
Plus (+)
.
Example when entering a telephone number You can interrupt the dialogue at any time
by pressing the PTT
button or with the
voice command
CANCEL
.
Repeat last call–Press the button PTT
⇒
page 153, fig. 157
.
– Give the command
REDIAL
after the signal tone.
After giving this command, th
e last number selected via voice input is selected
again. Example of redial
Voice command
Activity
CALLS (SELECT)
The telephone number is selected.
REPEAT
The entered name or the digits are repeated. Then the system requests with voice response “
please
proceed
” the entry of further digits or commands.
BACK
The entered name or the last entered order of digits is erased. Previously entered groups of digits are repeated. Then the system requests with voice response “
and proceed?
” the entry of further digits
or commands.
DELETE
All entered digits are erased.
CANCEL
The dialogue is ended.A1
Voice command
Announcement
DIAL NUMBER
“ The number please
”
e.g.
SIX ZERO THREE
“Six zero three
”
“And proceed?
”
e.g.
ONE TWO THREE FOUR
“One, two, three, four
”
“And proceed?
”
z. B.
FIVE SIX
“Five, six
”
CALLS (SELECT)
“The number is being dialed
”
If no entry is put in, the following anno
uncement is made after about 5 seconds.“Possible commands are: dial, repeat, back, or delete
”
Voice command
Announcement
REDIAL
“The number is being dialed
”
A1
s2dk.1.book Page 157 Wednesday, April 8, 2009 12:23 PM

Communication
159
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Example for selecting the name In the case that the list
is empty, the message “
The name list is empty, main
menu
” sounds.
If the system does not recognize the name
called, it asks you to repeat using the
command “
Pardon?
”. If the system does not recognize the name to be called after
repeating, the message sounds “
The name does not exist. You receive the
current name list with LISTEN TO ALL THE NAMES, main menu
”.
You can interrupt the dialogue at any time
by pressing the PTT button or with the
voice command
CANCEL
.
Listening-in to the voice phonebook– Press the PTT button. – Give the command
LISTEN TO ALL THE NAMES
after the signal tone.
After giving this command, all voice record
ings are replayed from the list of the
control unit. By pressing the PTT butto
n when announcing th
e desired name, the
corresponding telephone number is being dialed; the system answers: “
The
number is being dialed
”.
Example for selecting the name In the case that the list is
empty, the system announces “
The name list is empty
”.
You can interrupt the dialogue at any time
by pressing the PTT button or with the
voice command
CANCEL
.
After replaying the complete list, the system announces “
End of name list
”.
Erase entries out of the phone voice phonebook– Press the PTT button. – Give the command
ERASE NAME
after the signal tone.
After giving this command, there is the possibility to erase a stored entry in the phone voice phonebook. Example for erasing an entry out of the phone voice phonebook You can interrupt the dialogue at any time
by pressing the PTT
button or with the
voice command
CANCEL
.
If the user answers with
NO
, the system answers with “
Cancel
” and the dialogue is
ended.Erase the complete phone voice phonebook– Press the PTT button. – Give the command
DELETE PHONEBOOK
after the signal tone.
After giving this command, there is the
possibility to erase the complete phone
voice phonebook.
Voice command
Announcement
CALL NAME
“ Call name
”
Name XYZ
“Do you want to call XYZ?
”
CALLS (SELECT)
“The name is being dialed
”
Voice command
Announcement
LISTEN TO ALL THE NAMES
“Interrupt using the voice button
”
Voice command
Announcement
DELETE NAME
“The name please
”
Name XYZ
“Do you want to erase XYZ?
”
YES
“The name is deleted
”
s2dk.1.book Page 159 Wednesday, April 8, 2009 12:23 PM

Communication
160
Example for erasing the complete phone voice phonebook You can interrupt the dialogue at any time
by pressing the PTT button or with the
voice command
CANCEL
.
If the user answers with
NO
, the system answers with “
Cancel
” and the dialogue is
ended.Inputs AUX-IN* and MDI*The inputs AUX-IN and MDI are located below the armrest of the front seats. The inputs AUX-IN and MDI connect the external audio sources (e. g. iPod or mp3 player) and record music from these device
s via your radio* or your navigation
system* installed in the factory. The description of the operation can be
found in the relevant Owner's Manual of
your radio* or your navigation*.
Note
•
The loudspeakers in the vehicle are matched to a power output of the radio and
navigation system of 4x 20°W.•
For the equipment sound system*, the loudspeakers are matched to a power
output of the amplifier of 4x40°W + 6x20 W.
CD changer*The CD changer for the radio and navigation system is located in the right side compartment of the luggage compartment. Loading a CD – Touch the button and guide the
CD (compact disc) into the CD-
case . The CD is automatically loaded onto the next free position in the CD-changer. The LED in the corresponding button stops flashing.
Loading all CDs – Hold the button pressed and guide all CDs one after the other into
the CD-case . The LEDs in the buttons are no longer flashing.
Loading a CD to one definite position – Touch button . The LEDs in the buttons light up at the memory
spaces, which are already assigned and flash in the case of free memory spaces.
– Touch the desired button and guide the CD into the CD-case .
Voice command
Announcement
DELETE ALL NAMES
“ Do you want to delete all the names?
”
YES
“Are you sure?
”
YES
“All the names are deleted
”
Fig. 159 The CD changer
AC
AB
AD
AC
AB
AD
AC
AD
AD
AB
s2dk.1.book Page 160 Wednesday, April 8, 2009 12:23 PM

Communication
161
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Ejecting a CD – Touch the button , in order to eject a CD. For assigned memory
spaces, now the LEDs light up in the buttons .
– Touch the corresponding button . The CD is ejected. Ejecting all CDs – Hold the button pressed for more than 2 seconds, in order to eject
the CDs. All CDs in the CD-cha
nger are ejected consecutively.
Note
•
Always guide the CD into the CD-cas
e with the printed side pointing
upwards.•
Never push the CD with force into the
CD-case as the insertion is performed
automatically.•
After loading a CD into the CD-changer
, you must wait until the LED of the
corresponding button lights up. Then th
e CD-case is free to load the next
CD.•
If you have selected a position, on which a CD is already located, this CD will be
ejected. Take out the ejected CD and load the desired CD.
AA
AD
AD
AA
AB
AD
AB
s2dk.1.book Page 161 Wednesday, April 8, 2009 12:23 PM